Harbor Freight Tools Thermometer 92350 User Manual

POCKET INFRARED  
THERMOMETER WITH LASER  
92350  
ASSEMBLY AND OPERATING INSTRUCTIONS  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of  
this manual or any artwork contained herein may be reproduced in any shape or  
form without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
8.  
9.  
Maintain tools with care. Keep the Pocket Thermometer clean for better and safer  
performance. The handle must be kept clean, dry, and free from oil and grease at all  
times.  
Disconnect power. Turn off tool when not in use. Remove battery when not in use for  
a week.  
10. Stay alert. Watch what you are doing, use common sense. Do not operate any tool  
when you are tired.  
11. Check for damaged parts. Before using any tool, any part that appears damaged  
should be carefully checked to determine that it will operate properly and perform its  
intended function. Check for any broken parts or mounting fixtures; and any other  
condition that may affect proper operation. Any part that is damaged should be  
properly repaired or replaced by a qualified technician. Do not use the tool if any  
button does not turn On and Off properly.  
12. Guard against electric shock. Prevent body contact with grounded surfaces such as  
pipes, radiators, ranges, and refrigerator enclosures..  
13. Do not operate tool if under the influence of alcohol or drugs. Read warning  
labels if taking prescription medicine to determine if your judgment or reflexes are  
impaired while taking drugs. If there is any doubt, do not operate the tool.  
14. Maintenance. For your safety, service and maintenance should be performed  
regularly by a qualified technician.  
15. Pacemaker safety warning. People with pacemakers should consult with their  
physician(s) before using this product; operation of equipment in close proximity to a  
heart pacemaker could cause interference or failure of the pacemaker.  
16. Laser beams can cause permanent damage to eyes. Never point the laser beam  
at another human or animal.  
17. CAUTION - The use of controls or adjustments or performance of procedures  
other than those specified herein may result in hazardous radiation exposure.  
18. CAUTION - The use of optical instruments with this product will increase eye  
hazard.  
Note: Performance of this tool may vary depending on tool battery power.  
Warning:The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be under-  
stood by the operator that common sense and caution are factors which cannot be  
built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking, check to make sure the parts on page 5 are included. If any parts are  
missing or broken, please call Harbor Freight Tools at the number on the cover of this  
manual as soon as possible.  
SKU 92350  
For technical questions, please call 1-800-444-3353  
Page 3  
 
Operation  
Battery Replacement  
Note: The LCD will indicate the batteries are weak with a flashing display.  
1.  
Press gently on the plastic tab on the back of the unit to remove the battery compart-  
ment lid.  
2.  
Replace the batteries making sure the polarity symbols positive (+) and negative (-) on  
the batteries correspond to the polarity symbols in the battery compartment. Snap the  
lid back onto the unit. See FIGURE 1.  
FIGURE 1  
Note: While the batteries are out, you will need to set  
the “C” or “F” key to establish an LCD readout in either  
Fahrenheit or Celsius. Slide the “C” or “F” key under  
the batteries, to the appropriate side.  
Taking Measurements  
If you haven’t set the unit to read results in either Fahrenheit  
or Celsius, follow the directions in the note above before  
operation.  
Warning! Laser radiation is dangerous and can cause permanent eye damage. Do not  
stare into the beam or point it at others.  
Refer to the Assembly Drawing on page 5.  
1.  
Point the Pocket Thermometer at the object you wish to measure and press and hold  
the Thermometer Button on the side. The meter will turn on and display a reading. The  
reading will remain on 8 seconds after you let go of the Laser Button. The chart below  
shows the relation between the distance and the size of the area measured.  
2.  
If working in a dark area, press the backlight button to illuminate the reading briefly.  
The backlight will switch off automatically.  
Distance (D) to Spot Size (S)  
24@4  
Inches  
12@2  
6@1  
Pocket  
Thermometer  
Millimeters  
150@25  
300@50  
D:S = 6:1  
600@100  
Special Considerations: Make sure the surface of the object is not covered with frost, dust  
or other materials. For accurate results, clean all surfaces before measuring. If the surface  
you are measuring is highly reflective, (while it is cool) either paint it with a heat-resistant flat  
black paint or put a non-reflective tape on the spot you are measuring.  
Maintenance  
1.  
2.  
3.  
Keep the unit clean. Wipe it down with a lint free cloth.  
Make sure the laser is clear of any dirt or debris.  
Remove the batteries if you are not using the unit for extended periods of time.  
SKU 92350  
For technical questions, please call 1-800-444-3353  
Page 4  
 
Assembly Drawing  
Laser Opening  
Thermometer  
Button  
Backlight  
Button  
LCD  
Strap  
Note: No replacement parts available for this unit.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL  
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY  
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYERTHAT HE OR SHE IS QUALIFIED TO  
MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS QUALIFIEDTO REPLACE ANY PARTS  
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES  
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSEDTECHNICIANS AND NOT BYTHE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
SKU 92350  
For technical questions, please call 1-800-444-3353  
Page 5  
 

Graco Indoor Furnishings 310863M User Manual
GrandTec MP3 Player Grand MP3 Music Player User Manual
Greenheck Fan Fan MSCF BI User Manual
Haier Dishwasher DW12 PFE2 E User Manual
Haier Refrigerator ESR042PBB User Manual
Harbor Freight Tools Staple Gun 92196 User Manual
Harman Stereo Amplifier 518S User Manual
Heatiator Indoor Fireplace NNXT3933IL User Manual
Honeywell Water Dispenser F 76 S F User Manual
HP Hewlett Packard Tablet XU103UT User Manual