iHome MP3 Docking Station iH6 User Manual

Model iH6  
The Home System  
For Your iPod®  
Music  
Photos  
Extras  
Settings  
NOTE: THIS UNIT WILL NOT CONTROL OR CHARGE 3G iPod  
 
quick start  
1:power  
2:antenna  
3:inserts  
Select the dock insert for your  
iPod® model from the table  
below and place insert in dock.  
Never dock an iPod without  
an insert in place.  
Attach AC adaptor cable to  
jack on back of the iH6 and  
plug the other end into a  
wall socket.  
Snap AM antenna into provided  
stand, then plug antenna cable  
into socket on back of iH6.  
Move antenna 12away.  
iPod nano  
Insert 8  
iPod with video (60 GB)  
Insert 10  
iPod with video (30 GB)  
Insert 9  
iPod photo thick (40, 60 GB)  
Insert 7  
iPod photo thin (20, 30 GB)  
Insert 6  
iPod nano  
thick (40, 60 GB) iPod photo  
thick (60 GB) iPod with video  
thin (30 GB) iPod with video  
thin (20, 30 GB) iPod photo  
NOTE: If you do not have an insert for your iPod, please visit an Apple store,  
6:radio  
4:time  
5:iPod/shuffle  
• Press & hold the Time Zone  
button on back until it flashes  
• Turn the Set Wheel to select  
your time zone  
• Press the Time Zone  
button again.  
• Move the DST switch on back  
of unit to +1 or -1 (adds or  
subtracts an hour)  
Insert iPod® into dock with proper  
insert (iPod must not be in a skin  
or case) OR insert shuffle into shuffle  
dock.Both iPod and shuffle will  
charge while docked.Press iPod  
Button on iH6 to play iPod. Turn  
on shuffle,press play on shuffle and  
iPod button on iH6 to play shuffle.  
Press the Radio button and  
press again to select AM/FM  
band.Turn the Set Wheel to  
tune in a station. Press and hold  
a preset button (1, 2,3 or 4) to  
save the station as a preset.  
 
1
Controls and Indicators  
Dock ᕩ  
µ Sleep Button  
Shuffle Dock  
Preset Buttons ᕨ  
Radio/AM/FM1/FM2Button ᕧ  
¸ Set Wheel  
Volume Wheel ᕦ  
iPod Button ᕥ  
¹
Ƹ
EQ Button  
Alarm Reset/Power Off Button  
Alarm On/Off Button ᕤ  
Alarm 1 Button ᕣ  
Alarm 2 Button ᕢ  
Snooze/Dimmer Button ᕡ  
Clock Adjust Button Ƽ  
Line Out Jack ƻ  
AC Adaptor Jack ƺ  
ƽ Time Zone Button  
ƾ DST switch  
Line-in Jack  
FM Antenna  
AM Loop Antenna socket ƹ  
iH6 Display  
Sleep Display  
Time Display  
PM Indicator  
Alarm 1, Alarm 2 Indicators  
Volume Indicator  
Battery Low Indicator  
AM/FM1/FM2 Indicator  
Alarm Time AM/PM Indicator  
Daylight Saving Time  
Indicator  
iPod Indicator  
Radio Frequency / Alarm Time Display  
2
 
Using the iH6  
Connect iH6 to Power Source  
a) Plug the AC adaptor cable into the ƺ AC Adaptor Jack and the other end into a standard 120v wall socket. Adaptor must be  
plugged in to operate. The iH6 does not operate on batteries.  
Setting the Clock  
a) Press and hold the ƽ Time Zone Button until the display flashes.  
b) Turn the Set Wheel to select your time zone.  
c) Press the Time Zone Button again. The clock will display the current time in your time zone.  
d) To adjust the time for Daylight Saving Time, slide the ƾ DST switch to +1 to advance the time 1 hour.  
Slide to -1 to turn the clock back 1 hour.  
To Set Clock Manually  
a) Press and hold the Ƽ Clock Adjust Button. The clock display will flash.  
b) Turn the ¸ Set Wheel until the current time is displayed (a PM indicator appears when time is set to PM; there is no AM indicator).  
c) Press the Clock Adjust Button to accept the time. The year display will flash.  
d) Turn the Set Wheel to adjust the year and press the Clock Adjust Button. The date display will flash.  
e) Turn the Set Wheel to adjust the date and press the Clock Adjust Button. Two beeps will indicate clock setting is complete. Use  
DST switch to adjust for Daylight Saving Time.  
Using the Alarms  
Setting the Alarms  
a) Press and hold the Alarm 1 Button until the alarm time flashes to wake to iPod (buzzer alarm sounds if no iPod is detected)  
or the Alarm 2 Button to wake to the current radio station at a separate alarm time. You cannot wake to iPod shuffle.  
b) Turn the Set Wheel to set the alarm time (a PM indicator appears when time is set to PM; there is no AM indicator).  
c) Press the Alarm 1 Button again (or the Alarm2 Button if you are setting second alarm). Alarm is now armed, indicated by the  
numbered alarm clock icon (alarm 1 iPod or alarm 2 radio).  
Arming and Disarming Alarm (Turn Alarm Function ON and OFF)  
a) Press the Alarm On/Off Button to arm or disarm alarm functions. When armed, the related alarm icon appears in display.  
Resetting the Alarm to Come on the Next Day  
a) When the alarm is sounding, press the Ƹ Alarm Reset/Power Off Button to stop alarm and reset it to come on the following day.  
Snooze  
a) Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes later. Snooze  
can be pressed several times during the 1 hour alarm cycle.  
Sure Alarm  
The iH6 has a sure alarm feature so the buzzer alarm will still sound in the event of power failure, if backup batteries are installed.  
iPod and shuffle  
Playing and charging your iPod or shuffle  
a) Place proper insert for your iPod (see insert table under Quick Start) in Dock, then gently dock iPod. To use your shuffle,  
gently dock it in the Shuffle Dock. When docked, iPod and shuffle will charge until fully charged. Unit will not overcharge iPod  
or shuffle. Note: The iH6 will not control or charge 3G iPod models.  
b) Press the iPod Button to play iPod, and again to pause. For shuffle play, press iPod button and use controls on your shuffle.  
Do not play iPod and shuffle at the same time.  
c) Turn Volume Wheel to adjust iH6 volume up or down  
d) Press the EQ Button to select Treble, Bass or Balance. Turn the Set Wheel to adjust settings. EQ settings for iPod and radio  
mode are independent.  
e) Press Ƹ Alarm Reset/Power Off Button to turn iH6 and iPod off. To turn shuffle off, use shuffle controls.  
Note: If you dock an iPod with a drained battery, it may take up to 6 minutes of charging before the iPod will respond.  
3
 
Using the iH6  
Radio  
Setting up Antennas  
a) Snap AM loop antenna into provided stand, then plug AM antenna cable into ƹ AM Loop Antenna socket on back of unit.  
Move antenna 12” away from unit for best reception.  
b) Extend  
FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas.  
Tuning and Playing the Radio  
a) Press the Radio Button to select radio play mode. Press as needed to select AM, FM1 or FM2 radio band.  
b) Turn the Set Wheel to tune radio to a desired station.  
c) To memorize the current station as a preset, press and hold Preset Button 1,2,3 or 4. Repeat steps a,b,and c to preset up  
to 12 stations (4 AM, 8 FM). To listen to a preset station at any time, simply press the desired preset button.  
d) Turn the Volume Wheel to adjust iH6 volume up or down.  
e) Press the EQ Button to select Treble, Bass or Balance. Turn the Set Wheel to adjust settings. EQ settings for iPod and radio  
mode are independent.  
f) Press Ƹ Alarm Reset/Power Off Button to turn iH6 and iPod off.  
Using the Line-in and Line-out Jacks  
a) An audio patch cord comes with the iH6. Use it to play nondocking iPods or other audio devices through the iH6 Line-in Jack  
(one end in the device’s line out or headphones jack, the other in the iH6 line in jack). Make sure there is no iPod docked in the  
iH6 when using the line-in jack (however, you can charge shuffle while using line-in). Press the iPod Button.  
b) Use the ƻ Line Out Jack to connect the iH6 to the line-in jack of other audio devices such as a tape recorder or amplifier.  
The Volume Wheel of the iH6 does not control line-out volume (adjust on attached device instead). The Line Out Jack is not  
recommended for headphones.  
Using Sleep Mode  
Sleep mode lets you sleep to your iPod or the radio, gradually lowering the volume until the unit shuts off at the selected time.  
a) Press the µ Sleep Button to select an amount of time before the iH6 will turn off: 120, 90, 60, 30 or 15 minutes.  
b) Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).  
Using Dimmer  
a) Press the Snooze/Dimmer Button during normal operation to adjust brightness of LCD display.  
Replacing iH6 Backup Batteries  
Install/Replace Backup Battery  
The iH6 uses a backup battery system to provide continuous alarm operation and clock settings  
in the event of a power failure. If the Battery Low Icon located on the left of the display is flashing,  
it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise  
all settings may be lost during battery replacement.  
Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries  
as indicated. We recommend the use of alkaline batteries for longer life.  
Batteries information:  
Do not mix old and new batteries.  
Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries.  
4
 
Using The Remote Control Unit  
The Remote Control controls basic functions on the iH6 and certain iPod® functions when the iPod® is docked in the iH6.  
For best results, use the remote control within 12 feet of the unit.  
Skip to previous or next track when  
Power On/Off Alarm  
Reset Button  
Turns iH6 ON or OFF  
or reset alarm when  
alarm is sounding  
Button..............  
Button  
iPod is playing, or HOLD to scan  
current playing track. In radio mode,  
press to tune stations. HOLD to scan  
radio stations.  
_
Volume Button.....Lowers volume level  
Volume + Button.....Raises volume level  
EQ Button..............Set Treble, Bass and Balance  
iPod Play/Pause Button  
Selects iPod and  
plays track. In play  
mode , press to pause  
Mute Button  
Mutes volume  
settings for best sound  
Presets Select Button  
Cycles through AM  
Radio Button..........Selects Radio function, AM and  
FM1 and FM2 radio bands  
or FM radio presets  
Snooze mode when  
alarm sounds,  
otherwise dims  
display  
Snooze/Dimmer Button  
Install/Replace the Remote Control Batteries  
Battery  
The remote control batteries are already installed at the factory. When the remote control  
door  
stops operating or its range seems reduced, replace the batteries with new ones.  
1. The battery door is located on the back end of the unit.  
2. Press to release the battery door latch.  
3. Insert one “CR2032” 3-volt lithium batteries. Make sure the polarity (the + and – side  
of the battery) is correct.  
4. Replace the battery holder back in the remote control.  
NOTE: PLEASE DISCARD BATTERIES PROPERLY  
5
 
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety.  
However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating  
instructions carefully before installation and use, and keep these instructions handy for future reference. Take special  
note of all warnings listed in these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.  
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings.  
Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of  
air through the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating  
instructions or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or  
pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the  
unit to where it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for  
cleaning instructions.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any  
openings or vents located on the product.  
8. Attachments Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or  
cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will  
prevent damage to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result  
in a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A.  
B.  
C.  
D.  
E.  
the power supply cable or plug has been damaged.  
objects have fallen into or liquid has been spilled into the enclosure.  
the unit has been exposed to rain.  
the unit has been dropped or the enclosure damaged.  
the unit exhibits a marked change in performance or does not operate normally.  
12. Antenna – Do not connect an external antenna to the unit (other than that provided).  
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the  
power cable should be unplugged from the unit to prevent damage or corrosion.  
14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service  
personnel.  
6
 
Troubleshooting  
Possible Problem  
Solution  
Symptom  
iH6 does not turn on  
AC adaptor isn't plugged into a working wall socket Plug the AC adaptor into a working wall socket and plug the  
or not plugged into the power supply jack on back connector into the supply jack on the unit  
of the unit  
iH6 doesn’t respond  
iH6 requires a reset  
If unit is plugged in and doesn't respond, try resetting the unit by following  
these steps:  
a) remove iPod from dock  
b) unplug unit from power source  
c) remove back up batteries  
d) wait 1 hour, then resume use  
Remove your iPod from the dock and check for obstruction on the  
connectors in the dock and on your iPod. Then reseat it in the dock.  
iPod is not docked properly  
Battery Low icon always Batteries are weak  
flashing  
Replace with new batteries  
Batteries were not installed properly  
Check to make sure the polarity ( + and – ends) matches the diagram  
in the battery compartment  
iPod does not respond iPod is not docked properly  
to the unit/iPod is  
Remove your iPod from the dock and check for obstruction on the  
connectors in the dock and on your iPod. Then reseat it in the dock.  
Upgrade software on your iPod. For details visit  
playing but no sound  
Your iPod software is too old  
comes out  
iPod is locked up/plays but no sound  
comes out  
Check the volume setting. Make sure your iPod is working properly before  
docking into the unit. Please refer to your iPod manual for details. See  
above for software upgrade information.  
You may need to reset your iPod. To do so:  
1. Toggle the Hold switch to hold position, then off.  
2. Press and hold the Menu and center Select buttons at the same time until  
Apple logo appears. You may need to repeat this step.  
Using 1st or 2nd generation iPod, iPod Shuffle or iH6 cannot control those iPods or other devices.  
other devices.  
Battery weak  
Remote Control didn’t  
work  
Replace current battery with new battery  
Move within 30 feet of the unit.  
Remote Control is out of range of the iH6  
remote sensor  
iH6/iPod performance is The iH6 is reacting to external interference  
erratic  
Move unit away from potential sources of external interference such as  
computers, modems, wireless devices (routers) or fluorescent light.  
No sound from iH6  
Volume is set too low on iH6  
iPod is not installed properly  
Make sure volume is turned up  
iPod didn’t charge up  
Remove your iPod from the dock and check for obstruction on the  
connectors in the dock and on your iPod. Then reseat it in the dock.  
iPod is locked up/ frozen  
iPod battery has problem  
Please make sure your iPod is working properly before docking into the  
unit. Please refer to your iPod manual for details.  
No AM band radio  
AM loop antenna is not connected to the unit  
Plug the AM loop antenna connector to the jack on the back of the unit  
sound but others OK  
AM band radio is very  
noisy  
AM loop antenna isn’t located properly  
Move the AM loop antenna away from the main unit/iPod and rotate it  
for best reception  
7
 
Troubleshooting  
Possible Problem  
Solution  
Symptom  
Sound is distorted  
Volume level is set too high  
Sound source is distorted  
Decrease the volume  
If the iPod original sound source (MP3) is old or of poor quality, distortion  
and noise are easily noticed with high-power speakers. Try a different  
audio source such as a music CD.  
If you are using an external sound source like older generation of iPod  
or iPod Shuffle, try reducing the output volume on the device itself. Also  
try turning bass boost OFF.  
Unit/adaptor gets warm This is normal  
after extended play at  
Turn unit off for awhile or lower volume  
high volume  
Can't hear  
Line out jack is not meant for headphones.  
Speakers need a power source  
The signal from the line out jack needs amplification. Use powered  
speakers/monitors or other amplified audio device.  
headphones/speakers  
attached to line out jack  
8
 
Solucionando problemas  
Síntoma  
Causa  
Solución  
El adaptador de corriente AC no está conectado a  
Conecte el adaptador de corriente a un tomacorriente que funcione  
La unidad no  
enciende  
un tomacorriente que funcione o no está conectado y a la parte posterior de la unidad  
en la parte posterior de la unidad  
La unidad no  
responde  
La unidad debe ser reprogramada  
Si la unidad está conectada y no responde, pruebe reprogramarla  
siguiendo estos pasos:  
a) Quite el iPod de la base  
b) Desconecte la unidad del tomacorriente  
c) Quite las baterías auxiliares  
d) Espere 1 hora y vuelva a probar  
No ha colocado el encastre del iPod, o está  
utilizando el encastre incorrecto.  
El iPod no encastra correctamente  
Verifique que el encastre sea el apropiado para su iPod  
El iPod no encastra  
correctamente  
Quite el iPod del encastre y retire la posible obstrucción del  
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.  
El ícono de batería Las baterías están gastadas  
Reemplace las baterías  
baja está  
Verifique que la polaridad de las baterías (- y +) se encuentren  
Las baterías no están instaladas  
destellando  
de acuerdo al diagrama del compartimiento de baterías.  
correctamente  
El iPod no se  
comunica con la  
unidad  
El iPod no está instalado correctamente  
Quite el iPod del encastre y verifique posibles obstrucciones del  
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.  
Su software es obsoleto  
Renueve su software. Para mayor información, diríjase a  
El iPod no responde  
Verifique que su iPod funcione correctamente antes de conectarlo  
a la unidad. Refiérase al manual de su iPod para más detalles.  
Usted tiene un iPod de primera o segunda  
generación, un Shuffle u otro tipo de aparato  
El iH6 no puede controlar estos otros aparatos  
No sale sonido  
de su iH6  
El volumen del iH6 se encuentra muy bajo  
El iPod no está instalado correctamente  
El iPod está trabado/no responde  
Asegúrese de subir el volumen  
El iPod no carga  
Quite el iPod del encastre y retire la posible obstrucción del  
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.  
Por favor asegúrese de que su iPod funcione correctamente antes  
de colocarlo en el encastre. Refiérase al manual de su iPod para  
mayor información.  
La batería del iPod podría tener algún  
inconveniente  
La banda de AM no  
La antena no está ubicada correctamente  
Aleje la antena de la unidad y gírela para mejorar la recepción  
suena pero las demás sí  
El sonido sale  
distorsionado  
El volumen se encuentra muy alto  
El sonido sale distorsionado de la unidad  
Baje el volumen  
Si el sonido original de su iPod era de pobre calidad, las  
distorsiones y ruidos se harán más notables con los  
parlantes de alta potencia. Pruebe utilizar otra fuente de  
audio como un CD.  
Si está utilizando un iPod de primeras generaciones o un Shuffle,  
intente bajar el volumen de su aparato. También intente apagar  
el amplificador de bajos  
El control remoto  
no funciona  
Las baterías están gastadas  
Reemplace las baterías por nuevas  
No está apuntando el control remoto hacia el  
iH6  
Apunte el control remoto hacia el iH6 y manténgase a una distancia  
máxima de 10 pies de la unidad.  
9
 
Solucionando problemas  
Síntoma  
Causa  
Solución  
La unidad recalienta Esto es normal  
luego de largos  
Apague la unidad o baje el volumen  
períodos de uso a  
alto volumen  
No puede  
La línea de salida no está diseñada para  
La señal de salida require amplificación. Utilice parlantes u otra  
clase de aparto amplificado.  
escuuchar los  
auriculares/parlant  
es que están  
conectados a la  
ficha de salida “line  
out”  
auriculares. Los parlantes necesitan una fuente  
de alimentación  
El funcionamiento  
del iH6/iPod es  
errático.  
El iH6 está reaccionando a interferencias  
externas.  
Aleje la unidad de Fuentes potenciales de interferencia externa  
como computadoras, modems, ruteadores inalámbricos, luz  
fluorescente, etc.  
10  
 
Limited 90-Day Warranty Information  
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from  
defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.  
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should  
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies  
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,  
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service  
Center listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase  
is $30.00.  
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries  
are the most common cause of problems encountered.  
If service is still required:  
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.  
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.  
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of purchase).  
4. Send the unit prepaid and insured, to the Factory Service Center listed below.  
Consumer Repair Department  
SDI Technologies Inc.  
1330 Goodyear Dr.  
El Paso, TX 79936-6420  
Disclaimer of Warranty  
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which  
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized  
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes  
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.  
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original  
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members  
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive  
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may  
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually  
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies product.  
For operating instructions: 1-877-ihome01(1-877-446-6301) Toll Free  
For any other questions: 1-800-288-2792 Toll Free  
iH6USBIB-080106-4  
Printed in China  
 

Hamilton Beach Oven 840073100 User Manual
Honeywell Air Cleaner 61500 User Manual
Hotpoint Cooktop E6005 User Manual
HP Hewlett Packard Digital Camera SNPRB 0603 User Manual
HP Hewlett Packard Microwave Oven HP53151A User Manual
HP Hewlett Packard Personal Computer A7857 90023 User Manual
HP Hewlett Packard Printer Z6100ps User Manual
Hunter Fan Universal Remote 44758 User Manual
Hypercom Network Card Mobile Network User Manual
Iiyama Computer Monitor E2201W User Manual