¨
Patent Pending
Model No. IMBE40890
Serial No.
USERÕS MANUAL
Write the serial number in the
space above for reference.
Serial Number
Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that there
are missing or damaged parts,
we will guarantee you complete
satisfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
11. The weight bench is designed to support a
maximum of 560 pounds, including the user,
a barbell and weights. Do not place more
than 310 pounds, including the barbell, on
the weight rests. Do not place more than 150
pounds on the weight carriage. Do not place
more than 150 pounds on the leg lever for
normal use.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental or institutional setting.
12. Make sure that the cable remains on the pul-
leys at all times. If the cable binds as you are
exercising, stop immediately and make sure
that the cable is on the pulleys.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.
13. Check the cables periodically to make sure
that they are tight. See assembly step 12 on
page 10 for cable tightening instructions.
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
14. Always set both weight rests and both safety
spotters at the same height.
6. Keep children under 12 and pets away from
the weight bench at all times.
15. Always exercise with a partner. When you
are performing bench press exercises or toe
raise exercises, your partner should stand
behind you to catch the barbell if you cannot
complete a repetition.
7. Keep hands and feet away from moving
parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
16. Always disconnect the lat bar from the
weight bench when performing an exercise
that does not use the lat bar.
9. Always make sure there is an equal amount
of weight (not included) on each side of your
barbell (not included).
17. Always secure weights with the included
weight clips when they are mounted on a
barbell, the leg lever, or the weight carriage.
10. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
3
Before You Begin
Thank you for selecting the versatile IMAGE¨ 3.4
Weight Bench. The IMAGE¨ 3.4 is designed to help
you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic mus-
cle size and strength, or a healthier cardiovascular
system, the 3.4 Weight Bench will help you achieve
the specific results you want.
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is IMBE40890. The
serial number can be found on a decal attached to the
IMAGE¨ 3.4 Weight Bench (see the front cover of this
manual).
For your benefit, read this manual carefully before
using the IMAGE¨ 3.4 Weight Bench. If you have
additional questions, please call our Customer Service
Department toll-free at 1-800-999-3756, Monday
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Assembled
Dimensions:
Height: 72Ó
High Pulley
Station
Base: 56Ó x 84Ó
Lat Bar
Right Side
Left Side
Weight Rest
Safety Spotter
Weight
Carriage
Curl Pad
Backrest
Leg Lever
Adjustment
Tube
Low Pulley
Station
Seat
Weight
Tube
Note: The terms Òright sideÓ and Òleft sideÓ are determined relative to a person sitting on the bench;
they do not correspond to right and left on the drawings in this manual.
4
R0999A
Part Identification ChartÑModel No. IMBE40890
M10 x 19mm Bolt (57)Ð1
M6 Washer (30)Ð4
M8 Washer (23)Ð2
M10 Washer (6)Ð15
M10 x 48mm Bolt (55)Ð2
M8 Nylon Locknut (13)Ð2
M10 Nylon Locknut (11)Ð29
M10 x 62mm Carriage Bolt (59)Ð2
M8 x 64mm Bolt (43)Ð1
M10 x 65mm Bolt (67)Ð5
M10 x 68mm Bolt (33)Ð5
M8 x 68mm Bolt (60)Ð1
M10 x 72mm Bolt (68)Ð8
M10 x 75mm Bolt (8)Ð1
Protector Strip Screw (49)Ð14
M6 x 16mm Screw (3)Ð6
M6 x 38mm Screw (4)Ð4
M10 x102mm Bolt (71)Ð1
M10 x108mm Bolt (34)Ð3
M10 x 168mm Bolt (22)Ð1
5
Assembly
Before beginning assembly, carefully read the
following information and instructions:
¥ For help identifying the small parts, use the PART
IDENTIFICATION CHART on page 5.
¥ As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself!
Everything in this manual is designed to ensure
that our products can be assembled successfully
by anyone. However, it is important to recognize
that this is a sophisticated product with many
small parts and, consequently, assembly will
take time. Most people find that by setting aside
plenty of time, and by deciding to make the task
enjoyable, assembly will go smoothly.
The following tools (not included) are required
for assembly:
¥ Two (2) adjustable wrenches
¥ One (1) rubber mallet
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ Assembly requires two people.
¥ Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
¥ Lubricant, such as grease or petroleum jelly
plus soapy water.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Before beginning assembly, make sure that you
understand the information in the box above.
Note: Some of the parts described in the assem-
bly steps may be pre-assembled.
1
Press a 2Ó Square Inner Cap (17) into the indicated
end of the Right Stabilizer (26). Press a 2Ó Square
Outer Cap (58) onto the other end of the Stabilizer.
2
Press a 48mm Round Inner Cap (12) into each end of
the welded tube on the Right Stabilizer (26).
Press a 1.5Ó Square Inner Cap (72) into the storage
tube on the Right Upright (2).
Slide the Right Upright (2) onto the Right Stabilizer
(26) as shown. Attach the Upright to the Stabilizer
with an M10 x 65mm Bolt (67), two M10 Washers (6)
and an M10 Nylon Locknut (11). Do not tighten the
Nylon Locknut yet.
72
58
26
67
Set the upright assembly aside and make sure it
cannot fall over.
12
6
6
11
12
17
6
2. Press a 2Ó Square Outer Cap (58) onto each end of
the Left Stabilizer (25).
24
2
Press a 51mm x 76mm Inner Cap (24) into the top of
the Left Upright (1).
1
Insert two M10 x 62mm Carriage Bolts (59) into the
holes in the Left Stabilizer (25) from below.
Slide the Left Upright (1) onto the Left Stabilizer (25)
as shown, so the bracket on the Left Upright fits over
the M10 x 62mm Carriage Bolts (59) in the Left
Stabilizer.
Attach the Left Upright (1) to the Left Stabilizer (25)
with an M10 x 65mm Bolt (67), two M10 Washers (6),
and an M10 Nylon Locknut (11). Thread an M10
Nylon Locknut onto each of the M10 x 62mm
Carriage Bolts (59) in the Stabilizer. Do not tighten
the Nylon Locknuts yet.
11
11
58
67
6
6
25
58
59
3. Align the holes in a 4-hole Support Plate (16) with the
holes in the Right Upright (2). Insert four M10 x
72mm Bolts (68) into the Support Plate and the Right
Upright. Make sure that the Bolts are inserted from
the direction shown.
3
2
Align the holes in another 4-hole Support Plate (16)
with the holes in the Left Upright (1). Insert four M10
x 72mm Bolts (68) into the Support Plate and the Left
Upright. Make sure that the Bolts are inserted from
the direction shown.
While a second person holds the Right Upright (2),
slide the bracket on the Crossbar (20) over the four
M10 x 72mm Bolts (68) in the Right Upright. Make
sure that the Crossbar is turned so the warning
decal is on top. Attach the Crossbar with four M10
Nylon Locknuts (11). Do not tighten the Nylon
Locknuts yet.
1
68
16
68
Decal
11
11
11
Attach the Crossbar (20) to the Left Upright (1) as
described above.
20
68
11
16
68
7
4. Snap a Carriage Bushing (56) into the Weight Stop
(53). Slide both parts onto the Rear Upright (9), mak-
ing sure that the Carriage Bushing (56) is on top.
Attach the parts to the indicated hole in the Rear
Upright with an M8 x 68mm Bolt (60) and an M8
Nylon Locknut (13).
4
High Low
Side Side
60
6
9
hole
13
11
67
9
Next, slide the Rear Upright (9) onto the Right
56
53
6
Stabilizer (26). Make sure that the Rear Upright is
turned so the upper end slants in the direction
shown. Attach the Rear Upright with an M10 x 65mm
Bolt (67), two M10 Washers (6), and an M10 Nylon
Locknut (11). Do not tighten the Nylon Locknut yet.
26
5. Press Carriage Bushings (56) into the top and bottom
of the Weight Carriage (47).
5
45
11
Press a 48mm Round Inner Cap (12) into each end of
the weight tube on the Weight Carriage (47).
56
12
Identify the Upper Cable (45); this is the longest of
the two Cables. Note that the Cable has a ball/loop
on one end and a loop on the other end. Attach the
end with the loop to the indicated bracket on the
Weight Carriage (47) with an M10 x 19mm Bolt (57)
and an M10 Nylon Locknut (11). Make sure the Bolt
is inserted from the direction shown.
57
47
12
Slide the Weight Carriage (47) onto the Rear Upright
(9).
56
9
6. Press a 2Ó Square Inner Cap (17) into the open end
of the Top Frame (7).
6
17
Place the Top Frame (7) onto the Right Upright (2)
and the Rear Upright (9).
7
6
Attach the Top Frame (7) to the Right Upright (2) with
an M10 x 65mm Bolt (67), two M10 Washers (6) and
an M10 Nylon Locknut (11). Attach the Top Frame to
the Rear Upright (9) in the same manner.
67
6
67
6
11
11
9
2
8
7. The Upper Cable (45) was attached to the Weight
Carriage in step 5. Wrap the Upper Cable around a
Pulley (35) in the direction shown.
7
8
9
61
34
7
Attach the Pulley (35) and a Cable Trap (61) to the
indicated hole in the Top Frame (7) with an M10 x
108mm Bolt (34), a 15.8mm Spacer (31), an M10
Washer (6) and an M10 Nylon Locknut (11). Make
sure the Cable Trap is oriented as shown, so it
will hold the Cable in place.
31
35
6
11
45
8. Note: If the Pulley Plates (62) are pre-assembled,
remove both Pulleys (35) from the Pulley Plates.
Wrap the Upper Cable (45) around a Pulley (35) in
the direction shown. Attach the Pulley and a Cable
Trap (61) to the upper holes in the two Pulley Plates
(62). Note: Make sure that both Pulley Plates are
oriented as shown, so the ends with several holes
are pointed towards the floor. Attach the Pulley with
an M10 x 48mm Bolt (55) and an M10 Nylon Locknut
(11). Make sure the Cable Trap is oriented as
shown.
45
55
35
61
11
62
Holes
9. Wrap the Upper Cable (45) around a Pulley (35) in
the direction shown. Attach the Pulley and a Cable
Trap (61) to the indicated hole in the Top Frame (7)
with an M10 x 108mm Bolt (34), a 15.8mm Spacer
(31), an M10 Washer (6) and an M10 Nylon Locknut
(11). Make sure the Cable Trap is oriented as
shown.
61
34
31
7
6
35
45
11
10. Route the Upper Cable (45) over a Pulley (35) in the
direction shown. Attach the Pulley to the indicated
hole in the Top Frame (7) with an M10 x 108mm Bolt
(34), a 15.8mm Spacer (31), an M10 Washer (6) and
an M10 Nylon Locknut (11). Make sure the Cable is
between the Pulley and the welded pin (not visi-
ble) on the Top Frame.
10
7
34
35
31
6
45
Welded
Pin
11
9
11. Locate the Lower Cable (39) and note that it has a
ball/loop on one end and a loop only on the other.
See drawing 11a. Route the end of the Lower Cable
with the loop through the cable guide on the outside
of the Right Upright (2).
11
35
2
71
See drawing 11. Route the Lower Cable (39) around
a Pulley (35) in the direction shown. Attach the Pulley
and one end of the 2-hole Oval Support Plate (74) to
the welded tube on the Right Upright (2) with an M10
x 102mm Bolt (71) and an M10 Nylon Locknut (11).
Do not tighten the Nylon Locknut yet. Make sure
that the Support Plate is angled as shown and that it
is attached on the inside of the Upright (2).
Important: The Cable must be positioned between
the Pulley and the welded pin as shown in draw-
ing 11a.
39
Welded Tube
74
11
11a
2
39
35
Welded Pin
Hole for End of Cable
Cable Guide
12. Wrap the Lower Cable (39) around a Pulley (35) in
the direction shown. Attach the Pulley and a Cable
Trap (61) to the lower set of holes in the two Pulley
Plates (62) with an M10 x 48mm Bolt (55) and an
M10 Nylon Locknut (11). Make sure that the Cable
Trap is between the Pulley Brackets and that it is
oriented as shown.
12
55
62
Adjustment
Holes
11
61
35
Slide the loop on the Lower Cable (39) onto an M10 x
68mm Bolt (33). Insert the Bolt into the indicated hole
(see drawing 11a) in the Right Stabilizer (26) and
through the 2-hole Oval Support Plate (74). Secure
the Cable and Plate with an M10 Nylon Locknut (11).
1
IMPORTANT: The type of cable used on the
weight bench may stretch over time. If this
occurs, you can tighten the cables by moving the
lower Pulley (35) attached to the Pulley Plate (62).
To do this, remove the M10 x 48mm Bolt (55) and
the M10 Nylon Locknut (11). Move the Bolt to one
of the higher adjustment holes in the Pulley
Plates. As you re-attach the Pulley and the Cable
Trap (61), make sure the Cable Trap is oriented as
shown.
39
33
26
Go back and tighten all of the M10 Nylon
Locknuts (11) used in steps 1 through 12.
74
11
10
13. Insert two M10 x 68mm Bolts (33) into the 2-hole
Support Plate (70), the Front Leg (19), and the brack-
et on the Bench Frame (5) as shown. Tighten an M10
Nylon Locknut (11) onto each Bolt.
13
11
5
11
33
19
70
14. Align the bracket on the Bench Frame (5) with the
holes in the center of the Crossbar (20). Attach the
Bench Frame (5) to the Crossbar with two M10 x
68mm Bolts (33) and two M10 Nylon Locknuts (11).
14
33
5
11
20
15. Attach the Leg Lever Lock (41) to the indicated hole
in the Front Leg (19) with an M8 x 64mm Bolt (43),
two M8 Washers (23), and an M8 Nylon Locknut (13).
Do not overtighten the Nylon Locknut; the Leg
Lever Lock must pivot easily.
15
13
19
Attach the Bumper (48) to the indicated hole in the
Front Leg (19) with a Bumper Screw (64).
23
41
23
43
48
18
64
16. Press a 2Ó Square Inner Cap (17) into each end of
the Leg Lever (18). Press a 48mm Round Inner Cap
(12) into the end of the weight tube on the Leg Lever.
16
11
Lubricate
17
Lubricate an M10 x 75mm Bolt (8). Attach the Leg
Lever (18) to the bracket on the Front Leg (19) with
the Bolt and an M10 Nylon Locknut (11). Do not
overtighten the Nylon Locknut; it must be easy to
pivot the Leg Lever.
8
19
17
12
17
11
17. Press a 3/4Ó Round Inner Cap (54) into each end of
the three Pad Tubes (38).
17
10
19
Press a Foam Pad (10) onto one end of a Pad Tube
(38). Insert the Pad Tube into one set of holes in the
bracket on the Front Leg (19). Press a Foam Pad
onto the other end of the Pad Tube.
10
54
18
54
Mount the other two Pad Tubes (38) in the indicated
holes in the Leg Lever (18) as described above.
38
54
10
38
54
10
18. Press a 30mm Square Inner Cap (32) into each end
of the Adjustment Tube (29).
18
32
29
28
Press a 1Ó Square Inner Cap (28) into each end of
the two Backrest Tubes (27). Attach the Backrest
Tubes to the Backrest (15) with four M6 x 38mm
Screws (4) and four M6 Washers (30). Note: Make
sure the indicated holes in the Backrest Tubes are
oriented as shown (on the wide end of the
Backrest).
15
32
Holes
On This
End
27
30
28
4
30
30
4
19. Lubricate the M10 x 168mm Bolt (22). Attach the
Backrest (15) to the welded tube on the Bench Frame
(5) with the Bolt, two M10 Washers (6) and an M10
Nylon Locknut (11). Note: Do not overtighten the
Nylon Locknut; it must be easy to pivot the
Backrest.
19
15
22
6
5
6
Welded
Tube
11
20. Attach the Seat (14) to the brackets on the Bench
Frame (5) with four M6 x 16mm Screws (3). Make
sure that the wide end of the Seat is turned away
from the Backrest (15).
20
15
14
Wide
End of
Seat
5
3
12
21. Press 25.4mm Round Inner Caps (37) into the Weight
Rests (21, 66) and the Safety Spotters (63, 69).
21
21
Insert the Weight Rests (21, 66) into the Uprights (1,
2). Make sure that the Weight Rests are at the
same height and that the locking clips are hooked
around the Uprights.
2
37
1
63
66
Next, insert the Safety Spotters (63, 69) into the Uprights
(1, 2). Make sure that the Safety Spotters are at the
same height and that the locking clips are hooked
around the Uprights. The Safety Spotters must be
a few holes lower than the Weight Rests (21, 66).
69
22. Attach the Curl Pad (44) to the Curl Post (42) with
two M6 x 16mm Screws (3).
22
44
To use the Curl Pad (44), insert the Curl Post (42)
into the Front Leg (19) and line up one of the adjust-
ment holes in the Curl Post with the hole in the Front
Leg. Insert the Adjustment Knob (36) through the Curl
Post and tighten it into the welded nut on the Front
Leg.
42
3
36
23. Make sure all parts are properly tightened before
you use the weight bench. The use of all remain-
ing parts will be explained in Adjusting the Weight
Bench starting below.
19
Adjusting the Weight Bench
This section explains how to adjust the weight bench. See the exercise guidelines in the accompanying exercise
guide for important information on how to get the most benefit from your exercise program. Also, refer to the
exercise guide to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
2
1
The Backrest (15) can be set at a level position, a
declined position, or any of several inclined positions.
15
To change the incline of the Backrest, move the
Adjustment Tube (29) to a different set of adjustment
brackets on the Uprights (1, 2).
20
29
To set the Backrest (15) for a declined position, remove
the Adjustment Tube (29) and lower the Backrest onto
the Crossbar (20).
Tab
WARNING: Always make sure the locking tabs on
the Adjustment Tube (29) fit into the holes in the
adjustment brackets on the uprights.
29
Adjustment
Bracket
13
USING THE WEIGHT RESTS AND SAFETY SPOTTERS
Before beginning an exercise, insert the Weight Rests
(21, 66) and the Safety Spotters (63, 69) into the holes
in the Uprights (1, 2) that are best suited for the exer-
cise. The selected holes should be at the lowest point to
which you want your barbell to go during the exercise.
Perform the exercise as shown in the accompanying
exercise manual. Note: Make sure that the locking
clips are hooked around the Uprights.
2
21
Important: The Safety Spotters (63, 69) are designed
to minimize the risk of injury if the barbell is dropped
during standing exercises. The Safety Spotters are
deliberately designed to bend when hit with a barbell
loaded with heavy weights. This minimizes the risk of
the barbell bouncing off the Safety Spotters and
causing injury to the user. If you accidentally bend
the Safety Spotters, please call our Customer Service
Department (see the front cover of this manual) to
order replacement Safety Spotters.
1
Locking Clips
66
69
63
WARNING: Always set both weight rests and both
safety spotters at the same height.
ATTACHING WEIGHTS TO THE LEG LEVER
18
To use the Leg Lever (18), slide the desired amount of
weight (not included) onto the weight tube. Secure the
weights with a Weight Clip (50).
WARNING: Do not place more than 150 pounds on
the Leg Lever. Always secure the weights (not
included) with a Weight Clip (50).
Weight Tube
50
ADJUSTING THE FOAM PADS
The Foam Pads (10) inserted into the bracket on the
Front Leg (19) can be adjusted to two different positions.
To do this, pull one Foam Pad off the Pad Tube (38).
Move the Pad Tube to the other hole in the bracket on
the Front Leg. Push the Foam Pad back onto the Pad
Tube.
Bracket
38
10
19
14
ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE
To use the upper or lower pulley stations, slide the
desired amount of weight (not included) onto the weight
tube of the Weight Carriage (47). Secure the weights with
Weight Clips (50).
Weight
Tube
50
WARNING: Do not place more than 150 pounds on
the Weight Carriage. Always place the same
amount of weight (not included) on each side of
the Weight Carriage. Always secure the weights
with the Weight Clips (50).
50
47
LOCKING THE LEG LEVER
The Leg Lever (18) can be locked by rotating the Leg
Lever Lock (41) until it snaps into place over the Pad
Tube (38). Note: A Foam Pad has been removed for
clarity; it does not have to be removed to lock the
Leg Lever.
18
41
38
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE UPPER OR LOWER PULLEY STATIONS
To use the upper pulley station, attach the Lat Bar (46) or
the Nylon Strap (73) to the Upper Cable (45) with the
Cable Clip (40). The Lat Bar or Nylon Strap can be
attached to the lower pulley station in the same manner.
45
40
Other attachments, such as an ankle strap, can be
attached to the pulley stations as described above.
46
IMPORTANT: See assembly step 12 on page 10 for
information on how to tighten the cables.
73
ATTACHING THE CURL POST TO THE FRONT LEG
OR USING IT AS A SEAT
2
To use the Curl Pad (44), insert the Curl Post (42) into the
Front Leg (19) and line up one of the adjustment holes in
the Curl Post with the hole in the Front Leg. Insert the
Adjustment Knob (36) through the Curl Post and tighten it
into the welded nut on the Front Leg.
Storage
Tube
44
36
42
For certain exercises, the Curl Pad (44) can be used as a
seat. To do this, turn the Curl Pad around, compared to
the picture, and mount it on the storage tube on the Right
Upright (2). The Curl Pad can also be stored here when it
is not in use.
19
15
R0999A
Part ListÐModel No. IMBE40890
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
6
4
1
15
1
1
1
6
29
5
2
1
1
2
6
1
1
1
1
1
2
1
1
1
2
4
1
4
3
2
5
3
6
1
4
3
Left Upright
Right Upright
M6 x 16mm Screw
M6 x 38mm Screw
Bench Frame
M10 Washer
Top Frame
M10 x 75mm Bolt
Rear Upright
Foam Pad
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
#
1
2
1
1
1
1
1
1
1
1
14
2
4
2
1
6
2
3
1
3
2
1
4
2
1
1
2
1
5
8
1
1
1
1
1
1
1
1
Lower Cable
Cable Clip
Leg Lever Lock
Curl Post
M8 x 64mm Bolt
Curl Pad
Upper Cable
Lat Bar
Weight Carriage
Bumper
Protector Strip Screw
Weight Clip
Weight Clip Cover
Handgrip
Weight Stop
3/4Ó Round Inner Cap
M10 x 48mm Bolt
Carriage Bushing
M10 x 19mm Bolt
2Ó Square Outer Cap
M10 x 62mm Carriage Bolt
M8 x 68mm Bolt
Cable Trap
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
M10 Nylon Locknut
48mm Round Inner Cap
M8 Nylon Locknut
Seat
Backrest
4-hole Support Plate
2Ó Square Inner Cap
Leg Lever
Front Leg
Crossbar
Right Weight Rest
M10 x 168mm Bolt
M8 Washer
51mm x 76mm Inner Cap
Left Stabilizer
Right Stabilizer
Backrest Tube
1Ó Square Inner Cap
Adjustment Tube
M6 Washer
15.8mm Spacer
30mm Square Inner Cap
M10 x 68mm Bolt
M10 x 108mm Bolt
Pulley
Pulley Plate
Right Safety Spotter
Bumper Screw
Protector Strip
Left Weight Rest
M10 x 65mm Bolt
M10 x 72mm Bolt
Left Safety Spotter
2-hole Support Plate
M10 x 102mm Bolt
1.5Ó Square Inner Cap
Nylon Strap
Adjustment Knob
25.4mm Round Inner Cap
Pad Tube
2-hole Oval Support Plate
UserÕs Manual
Exercise Guide
#
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
R0999A
Exploded DrawingÐModel No. IMBE40890
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
1. The MODEL NUMBER of the product (IMBE40890)
2. The NAME of the product (IMAGE¨ 3.4 Weight Bench)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
IMAGE is a registered trademark of ICON Health & Fitness, Inc.
Part No. 157727 R0999A
Printed in China © 1999 ICON Health & Fitness, Inc.
|