Hunter Fan Outdoor Ceiling Fan Outdoor Ceiling Fan User Manual

INSTALLATION INSTRUCTIONS FOR OUTDOOR USE  
HUNTER CEILING FANS USING INSTALLER’S CHOICE MOUNTINGS  
READ AND SAVE THESE INSTRUCTIONS  
CAUTION:  
Step 3: Installation  
1. Read entire instructions carefully before beginning installation.  
2. To avoid possible shock, be certain electricity is shut off at  
main panel before wiring.  
3. All wiring must be in accordance with national and local  
electrical codes. If you are unfamiliar with wiring, you  
should use a qualified electrician.  
CAUTION: Your Hunter ceiling fan with accessories can weigh  
up to 35 lbs. The following precautions must be taken for safety  
and to ensure that your fan is securely mounted to the ceiling.  
• Be certain electricity is “off ” at fuse panel when inspecting or  
preparing the installation site.  
• All wiring and installation must meet local and national elec-  
trical codes.  
WARNING:  
1. To reduce the risk of personal injury, do not bend the blade  
brackets when installing the brackets, balancing the blades,  
or cleaning the fan. Do not insert foreign objects in between  
rotating fan blades.  
2. To reduce the risk of fire, electric shock or personal injury,  
mount to outlet box marked suitable for fan support.  
• Do not mount directly to an unsupported ceiling. Mounting  
must support a 35 lb. fan with accessories.  
A. Bring electrical cable into the outlet box and attach with an  
approved connector. Make certain that wiring meets all national  
and local electrical codes. Wire leads should extend at least 6"  
beyond outlet box for ease in making connections. See Figure 2.  
Step 1: Pre-Installation Instructions  
SUPPORTING STRUCTURE  
A. Select installation site. Check to make sure that in normal  
use no object can come in contact with the rotating fan blades.  
The mounting site should also meet the precautions listed in  
Step 3.  
B. Installation hardware is included for a standard ceiling. You  
will need an outlet box listed as “Suitable for outdoor use.”  
C. The fan blades must be mounted at least 7' above the floor.  
For maximum efficiency, there should not be any obstruction  
(walls, posts, etc.) within 24" of the blade tips. See Figure 1 for  
mounting distances.  
CONNECTOR  
6" MIN. LEAD LENGTH  
FIGURE 2  
Step 4: Installation of the Ceiling Plate  
And Neoprene Cover  
24"  
CLEARANCE  
A. Lay the neoprene cover over the ceiling plate. Orient so the  
notch is aligned with the ground screw which protrudes through  
the ceiling plate. See Figure 3. Pierce holes in the neoprene  
through the slots in the ceiling plate at a spacing to match the  
holes in the outlet box. Use the mounting screws to secure the  
ceiling plate and neoprene cover to the outlet box. See Figure 4.  
TO OBSTRUCTIONS  
7' MIN.  
TO FLOOR  
FIGURE 1  
PIERCED HOLES IN  
NEOPRENE COVER  
Step 2: Inspection of Fan  
A. Unpack unit carefully to avoid any damage to the components.  
B. Check for any shipping damage to the motor and the fan  
blades. If more than one fan is being installed, keep the matched  
and balanced fan blades in sets, as they were shipped. Should  
one of the fan blades become damaged during shipment, return  
all blades in the set for replacement.  
NOTCH  
PROTRUD-  
ING SCREW  
C. Check contents to be certain it contains a bag of parts.  
FIGURE 3  
B. If the fan is installed against a ceiling, insert the three rub-  
ber spacers into the three round holes provided in the ceiling  
plate. Locate the spacers between the ceiling plate and the neo-  
prene cover. See Figure 4.  
FORM NO. 41110-01 6/95  
- 1 -  
©1995 HUNTER FAN CO.TM  
 
NOTE: Some Hunter fans require a special adaptor plate  
between the switch housing and the light kit. This plate is pro-  
vided with those fans which need it. It should be installed as  
shown in Figure 5C. If the switch housing on your fan is 3-1/4"  
diameter or less you do not need the adaptor, mount the light kit  
directly to the switch housing.  
B. Position (2) slots in canopy directly under and in line with  
(2) mounting screws in ceiling plate. Lift fan until ceiling plate  
mounting screws are seated in bottom of slots in canopy. Rotate  
fan counterclockwise until both mounting screws drop into slot  
recesses. Tighten screws securely. Install third screw into mount-  
ing hole.  
CAUTION: Failure to securely assemble the canopy screws  
could result in the fan falling.  
NOTE: For the hanging fan configuration, rotate fan until  
groove in ball is positioned over tab in canopy. Make certain  
groove and tab are engaged before running fan. See Figure 7.  
Failure to do this could result in the fan falling.  
LIGHT KIT  
ADAPTOR  
Step 8: Fan Blade Assembly, Installation,  
and Balancing  
LIGHT KIT  
NOTE: Attach each blade with the central line (ridge) facing  
upward and flat side of blade facing downward. Correct installa-  
tion is with the ridge upwards towards the ceiling.  
FIGURE 5C  
Step 7: Finish Fan Assembly  
A. Attach wood blades to blade brackets using three screws  
for each blade. See Figure 8. If your blades have large holes  
you must first insert the rubber grommets into the holes. See  
Figure 8A.  
A. The ceiling plate has (3) mounting screw holes located on  
the side. Lift up the rubber cover and install (2) #10-32 X 1/2"  
Phillips round head screws halfway into two of these holes. See  
Figure 6.  
NOTE: Grommets are usually assembled by hand. If you use a  
tool, make certain you do not damage the grommet or blade  
when inserting the grommets.  
Remove the fan from the ceiling plate hook. Make sure not to  
break any wire connections. The canopy has (2) mating slots and  
(1) mating hole. See Figure 6.  
Next assemble the blade to the blade bracket. Make sure all  
screws are tight to prevent vibration or wobbling.  
RUBBER COVER  
Even when the screws are tight, the blades may seem to be  
loose. This is normal when using grommets and will not be a  
problem.  
CEILING PLATE  
RIDGE  
MOUNTING SCREWS  
BLADE  
MOUNTING HOLE  
CANOPY  
GROMMET  
MOUNTING SLOTS (2)  
FIGURE 8  
FIGURE 8A  
FIGURE 6  
B. Remove the screws and rubber bumpers from the motor  
hub. Insert a mounting screw (provided) in hole in blade bracket.  
Use a screwdriver to hold in place. Align blade holes with  
mounting holes in hub by turning screw and readjusting blade  
bracket until screw mates with threaded hole in hub. Do not  
tighten until both screws have been put in blade bracket. Repeat  
for all blades. See Figure 9.  
LEAD WIRES  
CANOPY  
C. A blade balancing kit has been provided with your fan.  
Should the fan wobble in operation, you may use this kit to cor-  
rect the balance per the instructions supplied with the kit.  
GROOVE IN BALL  
PIPE NIPPLE  
ROTATE BALL UNTIL GROOVE IN BALL  
ENGAGES TAB IN CANOPY  
FIGURE 7  
FORM NO. 41110-01 6/95  
- 3 -  
©1995 HUNTER FAN CO.TM  
 
Step 9: Operation of Fan  
A. Turn electrical service on at main panel.  
B. Switch operates in this sequence: “High,” “Medium,”  
“Low,” “Off.” Pull chain slowly to operate. Also, release the  
chain slowly so as to prevent chain from flying up into blades,  
possibly resulting in damage to blades, or pull chain. The break-  
away connector is designed to separate from the chain at a pre-  
determined force. If this separation occurs, simply reinsert the  
connector. It can be reused again and again. See Figure 9.  
PULL CHAIN  
SWITCH  
BLADE MOUNTING  
SCREWS  
BREAKAWAY  
CONNECTOR  
REVERSING  
SWITCH  
C. Motor is electrically reversible. When first operating fan,  
determine direction of air flow. If you wish to change direction,  
switch fan off and allow to stop. Slide reversing switch to the  
opposite position and switch fan back on. See Figure 9.  
NOTE: MAKE CERTAIN  
ALL SCREWS ARE  
TIGHT.  
PURCHASED ACCESSORY  
CHAIN (IF DESIRED)  
Speed Control  
FIGURE 9  
As an option, a wall mounted speed control switch is available  
from your Hunter dealer.  
TROUBLESHOOTING GUIDE  
PROBLEM  
PROBABLE CAUSE  
SOLUTION  
1. Power turned “off” or fuse blown.  
2. Loose wire connections or wrong  
connections.  
1. Turn power “on” or replace fuse.  
2. Loosen canopy. Check all connections (turn  
power “off” while checking).  
1. Nothing happens;  
fan does not move.*  
3. Motor reversing switch not engaged.  
4. Pull chain switch not “on.”  
5. Rubber shipping blocks not removed.  
3. Push switch firmly to one side or the other.  
4. Pull chain switch.  
5. Remove shipping blocks.  
*NOTE: If blades will not turn by hand, contact your nearest service representative.  
1. Blade brackets loosely screwed to motor.  
2. Blade screwed loosely to blade bracket.  
3. Blade cracked.  
1. Tighten screws until snug.  
2. Tighten screws.  
3. Replace all blades.  
2. Noisy operation.  
4. Non-approved speed control being used.  
4. Change to approved speed control.  
3. Excessive wobbling.  
1. Blade brackets not attached at proper locations.  
2. Unbalanced blades.  
3. Fan too close to vaulted ceiling.  
4. Loose blades or blade brackets.  
5. Fan not secure on hanger assembly.  
1. Carefully review Step 8.  
2. Use blade balancing kit. (See Step 8C.)  
3. Lower or move fan.  
4. Tighten all screws.  
5. Turn power off. Support fan very carefully.  
Loosen canopy and hang correctly.  
When switching from medium to low speed, you may notice some fan wobble. When fan speed stabilizes at low speed, wobble will disappear.  
HUNTER FAN COMPANY  
2500 FRISCO AVENUE  
MEMPHIS, TN 38114  
©1995 HUNTER FAN CO.TM  
®
FORM NO. 41110-01 6/95  
- 4-  
 

Graco Stroller PD241044B User Manual
Graham Field Blood Pressure Monitor JB02017 User Manual
Hamilton Beach Oven 840117700 User Manual
Harbor Freight Tools Fishing Equipment 95493 User Manual
Harbor Freight Tools Laser Level 92801 User Manual
Hotpoint Refrigerator FF40P User Manual
Hotpoint Refrigerator FFB6200AX User Manual
HP Hewlett Packard MP3 Player RX3100 User Manual
HP Hewlett Packard Stroller 11690A User Manual
Husqvarna Snow Blower 1130SBEXP User Manual