Hotpoint Washer Dryer AQD1170D 697 E User Manual

Instructions for  
installation and use  
WASHER-DRYER  
!
This symbol reminds you to read this instruction manual.  
EN  
Contents  
EN  
English,1  
Installation, 2-3-4-5  
Unpacking and levelling  
Connecting the electricity and water supplies  
Technical data  
Care and maintenance, 6  
Cutting off the water and electricity supplies  
Cleaning the machine  
Cleaning the detergent dispenser drawer  
Caring for your appliance drum  
Cleaning the pump  
Checking the water inlet hose  
Precautions and advice, 7  
General safety  
Load balancing system  
Disposal  
AQUALTIS  
Opening the porthole door manually  
AQD1170D 697 E  
AQD1170D 697 I  
Description of the machine, 8-9  
Touch control panel  
How to run a wash cycle or a drying  
cycle, 10  
Wash cycles and options, 11  
Table of wash cycles  
Wash options  
Detergents and laundry, 12  
Detergent  
Preparing the laundry  
Washing recommendations  
Trouble shooting, 13-14  
Assistance, 15  
1
 
Connecting the drain hose  
• the socket is compatible with the washing  
machines plug. If this is not the case, replace  
the socket or the plug.  
EN  
Connect the drain  
hose, without  
bending it, to a  
Your appliance is now supplied with a 13 amp  
fused plug it can be plugged into a 13 amp  
socket for immediate use. Before using the  
appliance please read the instructions below.  
draining duct or a  
wall drain situated  
between 65 and 100  
cm from the floor;  
65 - 100 cm  
WARNING - THIS APPLIANCE MUST BE  
EARTHED.  
THE FOLLOWING OPERATIONS SHOULD  
BE CARRIED OUT BY A QUALIFIED  
ELECTRICIAN.  
The drain hose may  
be connected to  
an under-sink trap.  
Before connecting  
the drain hose from  
the machine ensure  
that any blanks or  
removable ends  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be  
used, and the fuse cover re-fitted. If the fuse  
cover is lost, the plug must not be used until a  
replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
have been taken off  
the spigot.  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must  
be of the correct colour as indicated by  
the coloured marking or the colour that is  
embossed in words on the base of the plug.  
Replacements can be obtained directly from  
your nearest Service Depot.  
If it is placed over  
the edge of a basin  
or sink be sure  
the free end of the  
hose should not be  
underwater.  
Removing the plug:  
If your appliance has a non-rewireable  
moulded plug and you should wish to re-route  
the mains cable through partitions, units etc.,  
please ensure that either:  
! We advise against the use of hose extensions;  
in case of absolute need, the extension must  
have the same diameter as the original hose  
and must not exceed 150 cm in length.  
Ensure that if the drain hose is pushed into a  
standpipe, that the end does not go down more  
than 15cms (6 inches). If the hose is pushed  
down too far, this may cause the machine to self  
-syphon ie. continuously empty as it is filling.  
the plug is replaced by a fused 13 ampere  
rewireable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13  
amp cable outlet, controlled by a switch, (in  
compliance with BS 5733) which is accessible  
without moving the appliance.  
Disposing of the plug:  
Ensure that before disposing of the plug itself,  
you make the pins unusable so that it cannot  
be accidentally inserted into a socket.  
Electric connection  
Before plugging the appliance into the mains  
socket, make sure that:  
• the socket is earthed and in compliance  
with the applicable law;  
Instructions for connecting cable to an  
alternative plug:  
• the socket is able to sustain the appliances  
maximum power load indicated on the  
Technical Data Plate fixed on the machine.  
• the supply voltage is included within the  
values indicated on the Technical Data  
Plate fixed on the machine.  
Important: the wires in the mains lead are  
coloured in accordance with the following code:  
Green & Yellow  
Blue  
Brown  
Earth  
Neutral  
Live  
3
 
As the colours of the wires in the lead may  
not correspond with the coloured markings  
identifying the terminals in your plug, proceed  
as follows:  
! The power supply cable must only be  
EN  
replaced by an authorised serviceman.  
Warning! The company denies all liability if and  
when these norms are not respected.  
Connect Green & Yellow wire to terminal  
marked E or or coloured Green or Green &  
Yellow.  
Connect Brown wire to terminal marked L or  
coloured Red.  
Connect Blue wire to terminal marked N or  
coloured Black.  
If a 13 amp plug (BS 1363) is used it must be  
fitted with a  
13 amp fuse, either in the plug or adaptor or  
at the distribution board.  
If you are in any doubt regarding the electrical  
supply to your machine, consult a qualified  
electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
NEUTRAL (N)  
LIVE (L)  
EARTH (E)  
BROWN  
GREEN & YELLOW  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
Disposing of the appliance:  
When disposing of the appliance please  
remove the plug by cutting the mains cable  
as close as possible to the plug body and  
dispose of it as described on the previous  
page.  
! The washing machine should not be installed  
in an outdoor environment, not even where  
the area is sheltered, because it may be very  
dangerous to leave it exposed to damp, rain  
and thunderstorms.  
! When the washing machine is installed, the  
mains socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent  
or dangerously compressed.  
4
 
EN  
Technical data  
AQD1170D 697 E  
Model  
AQD1170D 697 I  
width 59.5 cm  
Dimensions height 85 cm  
depth 64.5 cm  
from 1 to 11 kg for the wash  
programme  
from 1 to 7 kg for the drying  
programme  
Capacity  
please refer to the technical  
data plate fixed to the ma-  
chine  
Electrical  
connections  
maximum pressure  
1 MPa (10 bar)  
minimum pressure  
0.05 MPa (0.5 bar)  
drum capacity 71 litres  
Water con-  
nections  
up to 1600 rotations per  
minute  
Spin speed  
Wash: programme ; tem-  
perature 60°C; using a load  
of 11 kg.  
Energy ra-  
ted  
programmes  
according to  
regulation  
EN 50229  
Drying: the smaller load  
must be dried by selecting  
the “EXTRA” dryness level.  
The load must consist of 3  
sheets and 7 pillowcases;  
the remainder of the load  
must be dried by selecting  
the “EXTRA” dryness level.  
This appliance conforms to  
the following EC Directives:  
- 2004/108/EC (Electromagne-  
tic Compatibility)  
- 2006/95/EC (Low Voltage)  
- 2002/96/EC  
5
 
Care and maintenance  
To access the pre-chamber:  
Cutting off the water and  
electricity supplies  
EN  
Turn off the water tap after every wash cycle.  
This will limit wear on the hydraulic system in  
the machine and help to prevent leaks.  
• Unplug the appliance when cleaning it and  
during all maintenance work.  
Cleaning the machine  
1. take off the cover panel on the front of the  
machine by first pressing it in the centre and  
then pushing downwards on both sides until  
you can remove it (see figures);  
The outer parts and rubber components of the  
appliance can be cleaned using a soft cloth  
soaked in lukewarm soapy water. Do not use  
solvents or abrasives.  
2. position a container  
so that it will collect the  
water which flows out  
(approximately 1.5 l)  
(see figure);  
3. unscrew the lid by  
rotating it in an anti-  
clockwise direction (see  
figure);  
Cleaning the detergent dispenser  
drawer  
To remove the drawer,  
1
press lever (1) and pull  
the drawer outwards (2)  
1
(see figure).  
Wash it under running  
2
water; this procedure  
4. clean the inside thoroughly;  
5. screw the lid back on;  
6. reposition the panel, making sure the hooks  
are securely in place before you push it onto  
the appliance.  
should be repeated  
frequently.  
2
Caring for your appliance drum  
Checking the water inlet hose  
• Always leave the door ajar to prevent  
unpleasant odours from forming.  
Check the inlet hose at least once a year. If  
there are any cracks, it should be replaced  
immediately: during the wash cycles, water  
pressure is very strong and a cracked hose  
could easily split open.  
Cleaning the pump  
The washing machine is fitted with a self-  
cleaning pump which does not require any  
maintenance. Sometimes, small items (such  
as coins or buttons) may fall into the protective  
pre-chamber at the base of the pump.  
! Make sure the wash cycle has finished and  
unplug the appliance.  
6
 
Precautions and tips  
! The machine was designed and constructed in  
Load balancing system  
EN  
accordance with international safety regulations. The  
following information is provided for safety reasons and  
must therefore be read carefully.  
General safety  
Before every spin cycle, to avoid excessive vibrations  
before every spin and to distribute the load in a uniform  
manner, the drum rotates continuously at a speed which  
is slightly greater than the washing rotation speed. If,  
after several attempts, the load is not balanced correctly,  
the machine spins at a reduced spin speed. If the load is  
excessively unbalanced, the Washer-dryer performs the  
distribution process instead of spinning. To encourage  
improved load distribution and balance, we recommend  
small and large garments are mixed in the load.  
This appliance can be used by children  
aged from 8 years and above and  
persons with reduced physical, sensory or  
mental capabilities or lack of experience  
and knowledge if they have been given  
supervision or instruction concerning use of  
the appliance in a safe way and understand  
the hazards involved. Children shall not  
play with the appliance. Cleaning and user  
maintenance shall not be made by children  
without supervision.  
Disposal  
• Disposing of the packaging materials: observe local  
regulations so that the packaging may be re-used.  
• The European Directive 2002/96/EC relating to Waste Electrical  
and Electronic Equipment (WEEE) states that household  
appliances should not be disposed of using the normal solid  
urban waste cycle. Exhausted appliances should be collected  
separately in order to optimise the cost of re-using and recycling  
the materials inside the machine, while preventing potential  
damage to the atmosphere and to public health. The crossed-  
out dustbin is marked on all products to remind the owner of  
their obligations regarding separated waste collection.  
For more information relating to the correct disposal of  
household appliances, owners should contact their local  
authorities or appliance dealer.  
– Do not dry unwashed items in the tumble dryer.  
– Items that have been soiled with substances such  
as cooking oil, acetone, alcohol, petrol, kerosene,  
spot removers, turpentine, waxes and wax removers  
should be washed in hot water with an extra amount of  
detergent before being dried in the tumble dryer.  
– Items such as foam rubber (latex foam), shower caps,  
waterproof textiles, rubber backed articles and clothes  
or pillows fitted with foam rubber pads should not be  
dried in the tumble dryer.  
– Fabric softeners, or similar products, should be used  
as specified by the fabric softener instructions.  
– The final part of a tumble dryer cycle occurs without  
heat (cool down cycle) to ensure that the items are left  
at a temperature that ensures that the items will not be  
damaged.  
Opening the porthole door manually  
In the event that it is not possible to open the porthole door  
due to a powercut, and if you wish to remove the laundry,  
proceed as follows:  
1. remove the plug from the  
electrical socket.  
2. make sure the water level  
inside the machine is lower  
than the door opening; if  
it is not, remove excess  
water using the drain hose,  
collecting it in a bucket as  
indicated in the figure.  
3. remove the cover panel  
on the lower front part of the  
washer dryer (see overleaf).  
WARNING: Never stop a tumble dryer before the end of  
the drying cycle unless all items are quickly removed and  
spread out so that the heat is dissipated.  
• This appliance was designed for domestic use only.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
• Do not pull on the power supply cable when unplugging the  
appliance from the electricity socket. Hold the plug and pull.  
• Do not touch the drained water as it may reach  
extremely high temperatures.  
• Never force the porthole door. This could damage the  
safety lock mechanism designed to prevent accidental  
opening.  
• If the appliance breaks down, do not under any  
circumstances access the internal mechanisms in an  
attempt to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• If it must be moved, proceed with the help of two or  
three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washer dryer, make sure  
the drum is empty.  
• During the drying phase, the door tends to get quite hot.  
• Do not use the appliance to dry clothes that have been  
washed with flammable solvents (e.g. trichlorethylene).  
• Do not use the appliance to dry foam rubber or  
similar elastomers.  
4. pull outwards using the tab as indicated in the figure,  
until the plastic tie-rod is freed from its stop position; pull  
downwards until you hear a “click”, which indicates that the  
door is now unlocked.  
5. open the door; if this is still not possible repeat the  
procedure.  
6. reposition the panel, making sure the hooks are securely  
in place before you push it onto the appliance.  
• Make sure that the water tap is turned on during  
the drying cycles.  
7
 
Description of the machine  
CONTROL  
PANEL  
EN  
PORTHOLE DOOR  
PORTHOLE DOOR  
HANDLE  
KICK STRIP  
PORTHOLE DOOR  
washing additives compartment: for fabric softener  
or liquid additives. We recommend that the maximum  
level indicated by the grille is not exceeded, and that  
concentrated fabric softeners are diluted.  
Always use the handle to  
open the porthole door (see  
figure).  
TOUCH CONTROL PANEL  
To adjust the settings, gently  
press the icon inside the  
sensitive (touch control) area  
as illustrated in the figure.  
DETERGENT DISPENSER DRAWER  
The detergent dispenser  
drawer is located inside the  
machine and can be accessed  
by opening the door.  
For more information on  
detergent measures, please  
refer to the chapter entitled  
“Detergents and laundry”.  
Standby mode  
This washing machine, in compliance with new energy  
saving regulations, is fitted with an automatic standby  
system which is enabled after about 30 minutes if no  
activity is detected. Press the ON-OFF  
wait for the machine to start up again.  
Consumption in off-mode: 0,5 W  
Consumption in Left-on: 0,5 W  
button briefly and  
! Do not pour detergent into  
the compartment 1.  
A
Detergent should only be  
poured into the compartment 2.  
1
2
2. main wash compartment:  
If liquid detergent is used,  
it is recommended that the  
removable plastic partition A  
(supplied) be used for proper  
dosage.If powder detergent is  
B
used, place the partition into slot B.  
8
 
START/PAUSE button  
Touch control panel  
with indicator light  
SPIN  
WASH  
EN  
button  
CYCLE  
PHASE  
icons  
WASH CYCLE  
M1  
ECO  
indicator light  
M2  
TEMPERATURE  
SELECTOR knob  
button  
DISPLAY  
CHILD LOCK  
button with indicator light  
OPTION  
buttons  
Button with ON/OFF  
indicator light  
DELAYED START  
button  
DRYING  
button  
LOCK indicator light  
WASH CYCLE PHASE icons: these illuminate to indicate  
the progress of the wash cycle (Wash – Rinse  
Spin/ Drain – Drying ). The text lights up when  
the cycle is complete.  
Button with  
ON/OFF indicator light: press this briefly  
to switch the machine on or off. The green indicator light  
indicates that the machine is switched on. To switch off  
the Washer-dryer during the wash cycle, press and hold  
the button for approximately 3 seconds; if the button is  
pressed briefly or accidentally the machine will not switch  
off. If the machine is switched off during a wash cycle, this  
wash cycle will be cancelled.  
START/PAUSE button with indicator light: when the  
green indicator light flashes slowly, press the button to  
start a wash cycle. Once the cycle has begun the indicator  
light will remain lit in a fixed manner. To pause the wash  
cycle, press the button again; the indicator light will flash  
in an orange colour. If the “LOCK” indicator light is  
switched off, the door may be opened. To start the wash  
cycle from the point at which it was interrupted, press the  
button again.  
WASH CYCLE SELECTOR knob: may be turned in  
either direction. To select the most suitable wash cycle,  
please refer to the “Table of wash cycles”.  
The knob will not move during the wash cycle.  
M1-M2 buttons: press and hold one of the buttons to  
store a cycle with your own set preferences in the memory  
of the machine. To recall a previously-stored cycle, press  
the corresponding button.  
LOCK indicator light: indicates that the porthole door is  
locked. To open the door, pause the wash cycle (see “How  
to run a wash cycle or a drying cycle”).  
CHILD LOCK  
button with indicator light: to activate  
DRYING button  
: press to decrease or exclude drying;  
or deactivate the CHILD LOCK, press and hold the button  
for approximately 2 seconds. when the indicator light  
is illuminated, the control panel is locked. This means it  
is possible to prevent wash cycles from being modified  
accidentally, especially where there are children in the  
home.  
the selected drying level or time will appear on the display  
(see “How to run a wash cycle or a drying cycle”).  
TEMPERATURE  
button: press to modify or exclude  
the temperature setting; the value selected will appear  
on the display above (see “How to run a wash cycle or a  
drying cycle”).  
ECO indicator light: the  
icon lights up when, after  
SPIN CYCLE  
button: press to modify or exclude the  
altering the washing parameters, an energy saving of  
at least 10% is made. Furthermore, before the machine  
enters “Standby” mode, the icon will light up for a few  
seconds; when the machine is switched off the estimated  
energy saving will be around the 80% mark.  
spin cycle; the value selected will appear on the display  
above (see “How to run a wash cycle or a drying cycle”).  
DELAYED START  
button: press to set a delayed start  
for the selected wash cycle; the set delay time will appear  
on the display above (see “How to run a wash cycle or a  
drying cycle”).  
OPTION buttons: press to select the available options.  
The indicator light corresponding to the selected option will  
remain lit (see “How to run a wash cycle or a drying cycle”).  
9
 
How to run a wash cycle or a  
drying cycle  
WARNING: before you use the Washer-dryer for the first time,  
run a wash cycle with detergent and no laundry, using the 90°  
cottons cycle without pre-wash.  
Drying only  
EN  
Use the cycle selector knob to select a drying cycle (  
in accordance with the type of fabric. The desired drying level or  
-
-
)
time may also be set using the DRYING button  
.
1. SWITCH THE MACHINE ON. Press the button. All  
the indicator lights will illuminate for 1 second and the text  
AQUALTIS will appear on the display; the indicator light  
corresponding to the button will then remain lit in a constant  
manner and the START/PAUSE indicator light will flash.  
Setting a delayed start.  
To set a delayed start for the selected cycle, press the  
corresponding button repeatedly until the required delay period has  
been reached. During the setting procedure, the delay period and  
the text “Starts in:” will be displayed, along with the flashing  
2. SELECT THE PROGRAMME. Turn the PROGRAMME  
KNOB left or right, until the required programme has been  
selected; the name of the programme will appear on the  
display. A temperature and spin speed is set for each  
programme; these may be adjusted. The cycle duration will  
also appear on the display.  
symbol. After the delayed start has been set, the  
symbol  
will remain fixed on the display, which will also indicate the  
duration of the selected cycle with the text “Ends in:” and the  
cycle duration. Press the DELAYED START button just once to  
display the delay time set previously. After the countdown has  
begun, the display will show the text “Starts in:” and the delay  
period. Once the set delay time has elapsed, the machine will  
begin its cycle and the display will show “Ends in:” and the time  
remaining until the end of the cycle. To remove the delayed start  
option, press the button until the display shows the text OFF;  
3. LOAD THE LAUNDRY. Open the porthole door. Load the  
laundry, making sure you do not exceed the maximum load value  
indicated in the table of wash cycles on the following page.  
4. MEASURE OUT THE DETERGENT. Pull out the detergent  
dispenser drawer and pour the detergent into the relevant  
compartments as described in “Description of the machine”.  
the  
symbol will disappear.  
Modify the cycle settings.  
5. CLOSE THE PORTHOLE DOOR.  
• Press the button to activate the option; the name  
of the option will then appear on the display and the  
corresponding indicator light will illuminate.  
6. CUSTOMISE THE WASH CYCLE. Use the relevant  
buttons on the control panel:  
• Press the button again to deactivate the option; the  
name of the option will then appear on the display  
followed by the text OFF, and the corresponding  
indicator light will switch off.  
! If the selected option is not compatible with the selected  
wash cycle, this incompatibility will be signalled by the  
flashing of the indicator light and a sound alert  
(3 beeps); the option will not be activated.  
! If the selected option is not compatible with another  
option that has been selected previously, the indicator light  
corresponding to the first option selected will flash and  
only the second option will be activated; the indicator light  
corresponding to the button will remain lit in a constant manner.  
! The options may affect the recommended load value and/  
or the duration of the cycle.  
Modify the temperature and/or spin speed.  
The machine automatically displays the maximum temperature  
and spin speed values set for the selected cycle, or the most  
recently-used settings if they are compatible with the selected  
cycle. The temperature can be decreased by pressing the  
button, until the cold wash “OFF” setting is reached. The  
spin speed may be progressively reduced by pressing the  
button, until it is completely excluded “OFF”. If these buttons  
are pressed again, the maximum values are restored.  
Setting the drying cycle.  
The first time the button  
is pressed, the machine will  
automatically select the maximum drying cycle which is  
compatible with the selected wash cycle. Subsequent presses  
will decrease the drying level and then the drying time, until  
the cycle is excluded completely (“OFF”). If these buttons are  
pressed again, the maximum values are restored.  
7. START THE PROGRAMME. Press the START/PAUSE  
button. The corresponding indicator light remains lit in a fixed  
manner and the porthole door locks (the LOCK indicator  
light illuminates). The icons corresponding to the wash cycle  
phases will light up during the cycle to indicate which phase  
is currently in progress. To change a wash cycle once it has  
already started, pause the Washer-dryer by pressing the  
START/PAUSE button; then select the desired cycle and  
press the START/PAUSE button again. To open the door  
during a wash cycle, press the START/PAUSE button; if the  
LOCK indicator light is switched off you may open the  
door. Press the START/PAUSE button again to restart the  
wash cycle from the point at which it was interrupted.  
Drying may be set as follows:  
A - Based on a set time period: between 20 and 180 minutes.  
B- Based on the desired laundry dryness level:  
Iron: suitable for clothes which will need ironing afterwards.  
the remaining dampness softens creases, making them  
easier to remove.  
Hanger: ideal for clothes which do not need to be dried fully.  
Cupboard: suitable for laundry which can be put back in a  
cupboard without being ironed.  
Extra: suitable for garments which need to be dried  
completely, such as sponges and bathrobes.  
If your laundry load to be washed and dried is much greater  
than the maximum stated load, perform the wash cycle,  
and when the cycle is complete, divide the garments into  
groups and put some of them back in the drum. At this  
point, follow the instructions provided for a “Drying only”  
cycle. Repeat this procedure for the remainder of the load.  
A cooling-down period is always added to the end of each  
drying cycle.  
8. THE END OF THE WASH CYCLE. This is indicated by  
the illuminated text END. The porthole door may be opened  
immediately. If the START/PAUSE indicator light is flashing,  
press the button to end the cycle. Open the door, unload  
the laundry and switch off the machine.  
! If you wish to cancel a cycle which has already begun, press  
and hold the  
switches off.  
button until the cycle stops and the machine  
10  
 
Wash cycles and options  
Table of wash cycles  
EN  
Detergent and  
additives  
Max.  
speed Drying  
(rpm)  
Max.  
load  
(kg)  
Max. temp.  
Cycle  
duration  
Icon Description of the wash cycle  
Fabric  
(°C)  
Wash  
softener  
Cotton Coloureds (2): lightly soiled whites and delicate colours.  
40°  
60°  
40°  
60°  
40°  
30°  
-
1600  
800  
800  
1600  
1600  
800  
-
-
-
-
11  
5
Synthetics Resistant  
Synthetics Resistant (4)  
5
Whites  
6
Coloureds (3)  
6
Darks  
6
Steam Refresh  
2
Wool Platinum Care: for wool, cashmere, etc.  
40°  
30°  
-
800  
0
-
2,5  
1
Ultradelicates  
Rinse  
1600  
11  
Spin and Pump out  
Wash&Dry  
-
30°  
-
1600  
-
-
-
-
11  
1
1600  
Drying Cottons  
Drying Wool  
-
-
7
-
-
-
2,5  
Drying Synthetics  
-
-
-
-
5
Cotton Whites: extremely soiled whites and resistant colours.  
Cotton Whites (1): heavily soiled whites and resistant colours.  
90°  
60°  
1600  
1600  
11  
11  
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as  
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.  
(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.  
For all Test Institutes:  
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle  
with a temperature of 60°C.  
2) Long wash cycle for cottons: set wash cycle  
3) Short wash cycle for cottons: set wash cycle  
4) Long wash cycle for synthetics: set wash cycle  
with a temperature of 40°C.  
with a temperature of 40°C.  
with a temperature of 40°C.  
Wash options  
Time Saver  
Steam Hygiene  
If you select this option, the wash cycle duration will be  
reduced by up to 50%, depending on the selected cycle,  
thereby guaranteeing simultaneous water and energy  
saving. Use this cycle for lightly soiled garments.  
This option enhances washing performance by generating  
steam during the wash cycle that eliminates any bacteria  
from fibres while treating them at the same time. Place the  
laundry in the drum, choose a compatible programme and  
select option “ “.  
! It cannot be used in conjunction with  
,
,
,
,
,
,
,
,
,
,
.
! The steam generated during washing machine operation  
may cause the porthole door to become hazy.  
Eco  
! It cannot be used in conjunction with  
,
,
,
,
,
The Eco Option saves energy by not heating the water  
used to wash your laundry – an advantage both to the  
environment and to your energy bill. Instead, intensified  
wash action and water optimisation ensure great wash  
results in the same average time of a standard cycle.  
,
,
,
,
,
,
.
Easy Iron  
By selecting this option, the wash and spin cycles will be  
modified in order to reduce the formation of creases.  
For the best washing results we recommend the usage of a  
liquid detergent.  
At the end of the cycle the washing machine drum will  
rotate slowly; the “Easy Iron” and START/PAUSE indicator  
lights will flash. To end the cycle press the START/PAUSE  
button or the “Easy Iron” button.  
! It cannot be used in conjunction with  
,
,
,
,
,
,
,
,
,
,
.
! It cannot be used in conjunction with  
,
,
,
,
,
,
,
,
.
Note: If you also want to run the drying cycle, this option is  
enabled only if combined with level “Iron”.  
11  
 
Detergents and laundry  
Steam Refresh: this programme refreshes garments by  
removing bad odours and relaxing the fibres (2 kg, roughly  
3 items). Insert dry items only (that are not dirty) and select  
Detergent  
EN  
The type and quantity of detergent required depend on  
the type of fabric you are washing (cotton, wool, silk, etc.),  
as well as its colour, the washing temperature, the level of  
soiling and the hardness of the water in the area.  
Measuring out the detergent carefully will avoid wastage  
and help to protect the environment: although they are  
biodegradable, detergents still contain ingredients which  
alter the balance of nature.  
programme “  
cycle is completed, so we recommend hanging them to  
dry. The “ “ programme makes ironing easier.  
“. The garments will be damp once the  
Moreover, with the “Steam Perfume” laundry balls, your  
favourite perfume can be added to your laundry. Place a  
few drops of perfume on the sponge contained inside the  
laundry ball, close it and insert it into the drum together  
with the laundry. Then launch the specific programme “  
“. At the end of the cycle, garments will be relaxed and  
fragrant.  
! Not recommended for wool or silk garments.  
! Do not add too much perfume to the sponge in order to  
avoid it dripping.  
We recommend the following:  
• use powder detergents for white cotton garments and  
pre-washing.  
• use liquid detergents for delicate cotton garments and  
for all low-temperature wash cycles.  
• use gentle liquid detergents for wool and silk garments.  
The detergent should be poured into the relevant  
compartment - or the dispenser placed directly inside the  
drum - before the wash cycle begins. In the latter case, it will  
not be possible to select the Cottons with pre-wash cycle.  
! Do not use hand washing detergents because these  
create too much foam.  
! Do not add softeners or detergents.  
Wool: the wool wash cycle on this Hotpoint machine has  
been tested and approved by The Woolmark Company  
for washing wool garments labelled as hand washable  
provided that the garments are washed according to the  
instructions on the garment label and those issued by the  
manufacturer of this washing machine. Hotpoint is the  
first washing machine brand to be approved by The  
Woolmark Company for Apparel Care- Platinum for its  
washing performance and consumption of energy and  
water. (M1135)  
Preparing the laundry  
• Shake out the garments before loading them into the machine.  
• Divide the laundry according fabric type (symbol on the  
washing instruction label) and colour, making sure you  
separate the coloured garments from the white ones;  
• Empty all pockets and check the buttons;  
• Do not exceed the values listed in the Table of wash cycles”,  
which refer to the weight of the laundry when dry.  
Ultradelicates: use programme  
garments having strasses or sequins.  
to wash very delicate  
How much does your laundry weigh?  
1 sheet  
400-500 g  
150-200 g  
400-500 g  
900-1200 g  
150-250 g  
400-500 g  
150-200 g  
We recommend turning the garments inside out before  
washing and placing small items into the special bag  
for washing delicates. Use liquid detergent on delicate  
garments for best results.  
To wash Silk garments and Curtains select cycle  
then option ; the machine will end the cycle while the  
laundry is soaking and the indicator light will flash. To  
drain the water so that the laundry may be removed, press  
the START/PAUSE button or the button.  
1 pillowcase  
1 tablecloth  
1 bathrobe  
1 towel  
1 pair of jeans  
1 shirt  
and  
Washing recommendations  
When selecting an exclusively time-based drying function,  
a drying cycle is performed at the end of the wash cycle  
that is particularly delicate, thanks to light handling and  
appropriate temperature control of the water jet.  
The recommended durations are:  
1 kg of synthetic garments --> 160 min  
1 kg of synthetic and cotton garments --> 180 min  
1 kg of cotton garments --> 180 min  
Whites: use this cycle  
programme is designed to maintain the brightness of  
white clothes over time.  
If the drying function is selected, a drying cycle automatically  
activates at the end of the wash cycle that resembles open-air  
drying, with the added advantages of preserving garments  
from yellowing due to sunlight exposure and preventing loss  
of whiteness caused by the possible presence of dust in the  
air. Drying cycles can only be selected on a level basis.  
to wash white clothes. The  
The degree of dryness depends on the load and fabric  
composition.  
Coloureds: use this cycle  
clothes. The programme is designed to maintain bright  
colours over time.  
to wash bright coloured  
Wash&Dry  
was designed to wash and dry lightly soiled  
garments quickly. This cycle may be used to wash and dry  
a laundry load of up to 1 kg in just 45 minutes.  
To achieve optimum results, use liquid detergent and pre-  
treat cuffs, collars and stains.  
Stubborn stains: it is wise to treat stubborn stains with  
solid soap before washing, and to use the Cottons with  
pre-wash cycle.  
Darks: use cycle  
to wash dark-coloured garments.  
This programme is designed to maintain dark colours over  
time. We recommend using a liquid detergent for the best  
results when washing dark-coloured garments.  
When you select the drying function, at the end of the  
washing cycle the machine will automatically perform a  
delicate drying cycle that preserves the colours of the  
garments. The display will show the level “Hanger”.  
Max. load: 3 kg.  
12  
 
Trouble shooting  
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),  
make sure that the problem cannot be solved easily using the following list.  
EN  
Problem:  
Possible causes / Solutions:  
The machine does not switch on.  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
The machine does not dry.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• The ‘DELAY TIMER’ has been selected.  
• The ‘CHILD LOCK’ is activated (see ‘The machine just ‘beeps’ when a  
programme or option is selected’ below).  
• Check the 2 sections above.  
• The ‘DRY’ button has been pressed to exclude drying.  
The clothes are too hot when the  
drying cycle is finished.  
• A cooling-down period is always added to the end of each drying cycle. If the  
clothes appear too hot to handle leave the door open to allow to cool further  
before removing from the machine.  
The machine does not fill with  
• The water inlet hose is kinked.  
water or Indicator light for the first • The water inlet hose is not connected to the water supply.  
wash cycle flashing rapidly.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or spin • The Pump filter is blocked.  
- (error lights flashing).  
• The drain hose is kinked (see “Installation”).  
New Installation - The blanking cap or spigot has not been removed if  
connected under a sink.  
• The drain hose or sink trap is blocked.  
The machine does not spin.  
• The Spin Speed is set to “OFF” position.  
The machine does not drain or spin • The ‘EASY IRON’ option is enabled at the end of the program the machine  
- ‘EASY IRON’ light flashes.  
drum will rotate slowly. To complete the wash cycle press the ‘START/PAUSE’  
or the ‘EASY IRON’ buttons (see Wash Cycles & Options).  
• Programme times will vary due to water pressure, the incoming water  
temperature and if the wash load goes out of balance. This will increase the  
programme times accordingly (see ‘ The machine wont spin properly’ below).  
The programme takes too long.  
• Programme times will vary due to water pressure, the incoming water  
temperature and if the wash load goes out of balance. This will increase the  
programme time accordingly (see ‘The machine wont spin properly’ below)  
- (Most Common Cause!)  
The Display sticks at one ‘time to  
end’ for more than 1 Minute or the  
Display changes the estimated ‘Time  
to End’ during the programme.  
• The display time is for guidance only - it is not a precise time to finish and  
may vary.  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
13  
 
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
EN  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than  
dispenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The Phase in Progress indicator  
lights flash rapidly at the same  
time as the ON/OFF indicator light.  
• Switch off the machine and unplug it, wait for approximately 1 minute and then  
switch back on again. If the problem persists contact Technical Assistance  
Centre.  
The machine smells.  
• The machine requires a service wash. Run a 90 degree wash cycle with  
detergent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
• If there is no power to the machine you need to perform the manual unlocking  
procedure (see Precautions & Tips).  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when  
the machine is washing.  
The word ‘DEMO’ appears  
intermittently in the display  
window and the drum slowly turns.  
To exit, switch machine off, then press and hold ‘START/PAUSE’ and ‘ON/OFF’  
buttons simultaneously for 3 seconds. Note the machine will need the language  
resetting.  
The machine just ‘beeps’ when a  
programme or option is selected  
(Child Lock Symbol is lit).  
• Deactivate the Child Lock feature by pressing and holding in the ‘CHILD  
LOCK’ button for 2 seconds.  
Clothes are coming out too wet on  
‘Steam Refresh’ cycle.  
• Only dry items are to be used for this program. The program refreshes  
garments by removing bad odours and relaxing the fibres, also making items  
easier to iron if required.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.  
14  
 
Assistance  
Guarantee  
12 Months Parts and Labour Guarantee  
EN  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown  
repairs for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of  
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost  
to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will  
be a charge for our engineers time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair  
bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where  
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace  
your machine or, if you prefer, give you your money back.  
15  
 
195098434.01  
09/2012  
-
Xerox Fabriano  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its working  
life than us - the manufacturer.  
EN  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee  
you must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoints continued commitment to helping the environment, Hotpoint reserves the right to use  
quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove  
the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged into a mains socket, and the door  
16  
 

Graco Baby Accessories PD261471A User Manual
Grizzly Biscuit Joiner G4815 User Manual
Haier Flat Panel Television L1509A A User Manual
Harbor Freight Tools Battery Charger 92775 User Manual
Hasbro Games Dr Busby User Manual
Hasbro Motorized Toy Car 34891 34890 User Manual
HP Hewlett Packard Printer 1000 User Manual
Hunter Fan Landscape Lighting 45100 User Manual
Husqvarna Lawn Mower 532 44 05 66 User Manual
IBM Switch L2 3 User Manual