Hotpoint Dishwasher SDUD 1200 User Manual

Instruction booklet  
DISHWASHER  
Contents  
EN  
Installation, 2-5  
Positioning and levelling  
Technical data  
English, 1  
Electrical connection  
Connecting the water supply  
Ecodesign Regulation  
Description of the appliance, 6  
Overall view  
Control panel  
Loading the racks, 7  
Lower rack  
Cutlery basket  
Upper rack  
Start-up and use, 8-9  
Starting the dishwasher  
Loading the detergent  
Washing options  
SDUD 1200  
Wash cycles, 10  
Wash cycle table  
Rinse aid and refined salt, 11  
Loading the rinse aid  
Loading the refined salt  
Care and maintenance, 12  
Shutting off the water and electricity supplies  
Cleaning the dishwasher  
Preventing unpleasant odours  
Cleaning the sprayer arms  
Cleaning the water inlet filter  
Cleaning the filters  
Leaving the machine unused for extended periods  
Precautions and advice, 13  
General safety  
Disposal  
Saving energy and respecting the environment  
Troubleshooting, 14  
After Sales Service, 15  
After Sales Service  
Essential Contact Information  
Parts and Accessories  
Appliance Registration  
Hotpoint Guarantee, 16  
 
The dishwasher meets the requirements set out by the  
regulations in force concerning safety and electrical  
equipment.  
Changing the Plug  
EN  
Cut off and dispose of the supplied plug if it does not fit  
your socket.  
Any technical checks should be conducted exclusively  
by a trained and authorised technician: Repairs carried  
out by unaithorised persons will invalidate the guarantee,  
as well as posing a potential hazard to the user.  
To avoid a shock hazard DO NOT insert the  
discarded plug into a socket anywhere else.  
The manufacturer declines all responsibility for damage  
to persons or property resulting from failure to observe the  
above precautions, from tampering with even a single  
component or from the use of non-original spare parts.  
Wires in the mains lead are coloured accordance with  
the following code:  
Green/Yellow -  
Earth  
Neutral  
Live  
Blue  
-
-
Electrical Connection  
Before inserting the plug into the electrical socket, make  
sure that:  
Brown  
If you change the plug, the colour of the wires in the mains  
lead may not correspond with the terminal markings in the  
plug, which if not coloured, could be:  
the socket is earthed and complies with current  
regulations;  
EARTH  
NEUTRAL ‘N’  
LIVE ‘L’  
‘E’ or  
the socket can withstand the maximum load of the  
appliance, which is indicated on the data plate located  
on the inside of the door (see Description of the  
appliance);  
Changing the Mains Lead  
A lead can be ordered from Hotpoint Service  
UK: 08709 066 066 or  
the power supply voltage falls within the values  
indicated on the data plate on the inside of the door;  
the socket is compatible with the plug of the appliance.  
If this is not the case, ask an authorised technician to  
replace the plug (see After Sales Service); do not use  
extension cables or multiple sockets.  
Republic of Ireland: 1850 302 220  
- If you have damaged the existing lead or require a longer  
one a charge will be made. It is strongly advised that this  
work is carried out by a qualified electrician.  
- If the domestic wiring includes a residual current-operated  
circuit breaker, ensure that it conforms to the latest  
regulations.  
Once the appliance has been installed, the power  
supply cable and the electrical socket should be easily  
accessible.  
The dishwasher must not be connected to the electricity  
supply while installation is being carried out.  
The cable should not be bent or compressed.  
If the power supply cable is damaged, it must be  
replaced by the manufacturer or its Technical Assistance  
Service in order to prevent all potential hazards. (See After  
Sales Service)  
- This appliance should only be connected to a 230/240V  
AC source, via a properly installed earthed socket.  
- Use the dishwasher solely in a domestic environment.  
- DO NOT stand or place heavy objects on the door when  
it is open, this could damage the door or cause the  
appliance to tip forward.  
This appliance must be earthed.  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not observed.  
Fuses:your appliance comes fitted with a plug and a 13A  
fuse. If you need to replace the fuse, only those rated at  
13A and ASTA approved to BS1362 should be used. If you  
lose the fuse cover, a replacement may be obtained from  
your local authorised Service Centre or Electrical company.  
Correct replacement is identified by colour coding or the  
marking on base of plug.  
DO NOT use the plug unless the fuse cover is fitted.  
3
 
Connecting the water supplies  
Sink Waste System  
Connect the outlet hose (without bending it) to a drain duct  
with a minimum diameter of 32 mm.  
EN  
Connection to the water and electricity supplies should  
only be performed by a qualified technician.  
The dishwasher should not stand on top of the water  
hoses or the electricity supply cable.  
Connecting the water inlet hose  
The water inlet and outlet hoses and the electricity supply  
cable may be positioned towards the right or the left in  
order to achieve the best possible installation.  
To a suitable cold water connection point: before  
attaching the hose, run the water until it is perfectly  
clear so that any impurities that may be present in the  
water do not clog the appliance; after performing this  
operation, screw the inlet hose tightly onto a tap with a  
¾ gas threaded connection.  
The outlet hose must be at a height ranging from 40 to 80  
cm (from 15’’ to 31’’) from the floor / surface where the  
dishwasher rests (A).  
before connecting the drain hose, remove any internal  
restrictions; this will prevent a build up of debris which  
could cause a blockage  
To a suitable hot water connection point: your  
dishwasher may be provided with hot water from the  
mains supply (if you have a central heating system with  
radiators) provided that it does not exceed a temperature  
of 60°C.  
remove any restrictions from the waste spigot and ensure  
that the sealing bung is removed (B).  
It MUST NOT be connected to a surface water drain.  
Screw the hose to the tap as described for connection  
to a cold water supply.  
• Untie the end of the GREY drainage hose from the rear of  
the appliance.  
If the inlet hose is not long enough, contact a specialist  
store or an authorised technician (see Assistance).  
The water pressure must be within the values indicated  
in the Technical data table (see Installation).  
If fitting an under sink  
waste disposal unit, cut out  
the membrane, bung or  
blanking plug.  
The hose should not be bent or compressed.  
The appliance must be connected to the water supply  
network using new hoses.  
Do not use old hoses.  
Ensure that the new hose supplied is connected and the  
old hose is disposed of safely.  
Ensure the drain hose is securely attached, to  
prevent it coming away while the machine is in use and  
causing a flood.  
DO NOT overtighten the hose connector, hand tight is  
sufficient.  
Fit hose to waste securely using a “Jubilee” type  
clip.  
Ensure the fill hose is not kinked.  
Tap connections*: A range of adaptors are available  
to suit your tap.  
DO NOT connect the dishwasher to a single outlet  
instantaneous water heater or an electric heater.  
* Only available in selected models.  
4
 
Anti-flooding protection*  
EN  
To ensure floods do not occur, the dishwasher:  
- is provided with a special system which blocks the water  
supply in the event of anomalies or leaks from inside the  
appliance.  
Some models are also equipped with the supplementary  
safety device New Acqua Stop*, which guarantees anti-  
flooding protection even in the event of a supply hose  
rupture.  
WARNING: HAZARDOUS VOLTAGE!  
Under no circumstance should the water inlet hose be cut  
as it contains live electrical parts.  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not observed.  
ECODESIGN REGULATION  
ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with  
a normal soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce  
consumption even further, only run the dishwasher when it is full.  
Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W  
Consumption data table for the main cycles  
Standard conditions*  
User conditions**  
Energy consumption  
(kWh/cycle)  
1,30  
Water consumption  
(l/cycle)  
14  
14  
Duration  
(min/cycle)  
150  
Energy consumption  
(kWh/cycle)  
1,15  
Water consumption  
(l/cycle)  
14  
13  
Duration  
(min/cycle)  
140  
INTENSIVE  
NORMAL  
1,05  
115  
0,95  
110  
* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.  
** Data is obtained by recording values when the appliance is operational and loaded with user crockery.  
5
 
Description of the appliance  
Overall view  
EN  
1.  
Upper rack  
2.  
3.  
4.  
5.  
Upper sprayer arm  
Tip-up compartments  
Rack height adjuster  
Lower rack  
6.  
7.  
Lower sprayer arm  
Cutlery basket  
8.  
Washing filter  
9.  
Salt dispenser  
10.  
11.  
12.  
Detergent and rinse aid dispensers  
Data plate  
Control panel***  
Select wash  
cycle button  
Control panel  
Start/Pause button  
and indicator light  
ON/OFF/RESET  
button  
Display  
Half load  
button  
Delay Start  
button  
Display  
Multi-functional  
Tablets button  
Washing  
indicator light  
Drying  
indicator light  
Low Rinse aid  
indicator light  
Time remaining  
light-up display  
Wash cycle number  
light-up indicator  
Delay Start  
indicator light  
Multi-functional tablets  
indicator light  
Low Salt  
indicator light  
Half load  
indicator light  
***Only in completely built-in models.  
* Only available in selected models.  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
6
 
Loading the racks  
Before loading the racks, remove all food residues from  
the crockery and empty liquids from glasses and cups.  
Arrange the crockery so that it is held in place firmly and  
does not tip over.  
Tilt A  
Tilt B  
Tilt C  
EN  
After loading the appliance, check that the sprayer arms can  
rotate freely.  
- Lift the tip-up compartment, slide it gently and position it in the  
desired tilt angle.  
Lower rack  
The lower rack can hold pans, lids, plates, salad bowls, cutlery,  
etc. as seen in the Loading examples.  
Plates and large covers should be placed at the sides of the  
rack, ensuring that they do not block the rotation of the upper  
sprayer arm.  
Adjusting the height of the upper rack  
In order to make it easier to arrange the crockery, the upper rack  
may be moved to a higher or lower level.  
Some dishwasher models are fitted with  
tip-up sections*, which can be used in  
a vertical position when arranging plates  
or in a horizontal position when  
arranging pans and salad bowls.  
The height of the upper rack should ideally be adjusted  
WHEN THE RACK IS EMPTY.  
Never lift or lower the rack on one side only.  
Open the left and right guide rail stops  
and pull out the rack; position it higher or  
lower as required, slide it along the guide  
rails until the front wheels are in place  
and close the stops (see figure).  
Cutlery basket  
The type of cutlery basket may vary according to the dishwasher  
model: The cutlery basket should be positioned at the front of  
the lower rack, by sliding it between the fixed inserts, or on the  
upper rack when the half load option has been selected (in models  
featuring this option).  
If the rack is fitted with Dual Space  
handles*(see figure), pull out the upper  
rack until it reaches its stop point, grip  
the handles at the sides of the rack and  
move it upwards or downwards, then  
slowly let it fall back into place.  
- It has a collapsible sliding  
system which means the  
cutlery can be arranged in  
the best possible way.  
Loading examples for the upper rack  
Knives and other utensils with sharp edges must be placed  
in the cutlery basket with the points facing downwards, or they  
must be positioned horizontally in the tip-up compartments on  
the upper rack.  
Cutlery basket positioning examples  
Loading examples for the lower rack  
Upper rack  
Items which should not be washed in the  
dishwasher  
Load this rack with delicate and lightweight crockery: glasses,  
tea and coffee cups, saucers, small salad bowls, saucepans  
and small saucepans which are not too soiled, using the Loading  
examples as a guide.  
Wooden items, objects with wooden or horn handles or glued-  
on parts.  
Items made from aluminium, copper, brass, pewter or tin.  
Items made from plastic material which is not heat-resistant.  
Antique or hand-painted porcelain.  
Antique silver. Silver which is not antique may, however, be  
washed in the dishwasher using a delicate wash cycle,  
provided that it does not come into contact with other metals.  
• Mugs and cups, long sharp knives and serving utensils: place  
these on the tip-up compartments**.  
Tip-up compartments with adjustable tilt*  
- The tilt feature can be used to increase the space in the upper  
rack, to position wine glasses with different stem lengths safely  
and to improve drying performance.  
We recommend the use of crockery which is dishwasher  
safe.  
* Only available in selected models. ** The number and position  
may vary.  
7
 
Start-up and use  
Starting the dishwasher  
Measuring out the detergent  
EN  
A good wash result also depends on the correct amount  
of detergent being used; exceeding the stated amount  
does not result in a more effective wash and increases  
environmental pollution.  
1. Turn the water tap on.  
2. Press the ON/OFF button: all the indicator lights on the  
control panel will light up for a few seconds.  
3. Open the door and pour in a suitable amount of detergent  
(see below).  
4. Load the racks (see Loading the racks) and shut the  
door.  
5. Select the wash cycle in accordance with the type of  
crockery and its soil level (see Table of wash cycles) by  
pressing the P button.  
6. Select the wash options* (see adjacent information).  
7. Start the cycle by pressing the Start/Pause button (fixed  
light). A long beep signals the start of the wash cycle; the  
wash cycle indicator light is illuminated and the time  
remaining until the end of the cycle is displayed.  
8. Two short beeps and one long one indicate the end of  
the wash cycle; the Start/Pause button switches off and the  
word END appears on the display. Switch off the appliance  
by pressing the ON/OFF button, shut off the water valve  
and unplug the appliance from the electricity socket.  
9. Wait for a few minutes before removing the crockery, in  
order to avoid burns. Unload the racks, beginning with the  
lower level.  
Only use detergent which has been specifically  
designed for dishwashers.  
DO NOT USE washing up liquid.  
Using excessive detergent may result in foam  
residue remaining in the machine after the cycle  
has ended.  
The use of tablets is only recommended for  
models which offer the MULTI-FUNCTIONAL  
TABLETS option.  
To achieve the best results from each washing  
and drying cycle, powder detergent, rinse aid liquid  
and salt should be used.  
Compartment A: Washing detergent  
Compartment B: Pre-wash detergent  
1. Open cover C by pressing  
button D.  
2. Pour in the detergent after  
consulting the Table of wash  
cycles:  
• For powder detergent use  
compartments A and B.  
- The machine will switch off automatically during  
certain periods of inactivity, in order to minimise  
electricity consumption.  
Modifying a wash cycle in progress  
• For detergent in tablet form:  
when the cycle requires 1 tablet,  
place it in compartment A and  
close the cover; when it requires 2, place the second tablet  
at the bottom of the appliance.  
If a mistake was made during the wash cycle selection  
process it is possible to change the cycle, provided that it  
has only just begun: once the wash cycle has started,  
switch off the machine by pressing and holding the ON/  
OFF/Reset button. Switch it back on using the same button  
and select the desired wash cycle and options.  
3. Remove detergent residues from the edges of the  
compartment and close the cover until it clicks.  
Adding extra crockery  
Press the Start/Pause button (the corresponding indicator  
light will flash). Open the door, taking care to avoid the  
escaping steam, and place the crockery inside the  
appliance. Press the Start/Pause button (fixed light): the  
cycle starts from the point at which it was interrupted.  
If the Start/Pause button is pressed so as to pause the  
machine, the wash cycle or the Delay Start* function  
(if selected) is interrupted.  
At this stage it is not possible to change the wash cycle.  
Accidental interruptions  
If the door is opened during the wash cycle, or if there is a  
power cut, the cycle stops. It starts again from the point at  
which it was interrupted once the door has been shut or  
once the electricity supply is restored.  
*Only available in selected models.  
8
 
Wash options  
Half load  
EN  
If there are not many dishes to be washed, a half load  
cycle may be used in order to save water, electricity and  
detergent. Select the wash cycle and press the HALF LOAD  
button: the indicator light will illuminate.  
The OPTIONS may only be set, modified or reset after  
the wash cycle has been selected and before the Start/  
Pause button has been pressed.  
Only the options which are compatible with the type of  
wash cycle set may be selected. If an option is not compat-  
ible with the selected was cycle (see Table of wash cycles),  
the corresponding LED flashes rapidly 3 times.  
Remember to halve the amount of detergent.  
It is better to use powder detergent in this case.  
This option is incompatible with the following wash  
cycle: Rapide wash.  
If an option is selected which is incompatible with another  
option or wash cycle selected previously, the incompat-  
ible option light will flash 3 times and switches off, while  
the most recently selected setting remains lit.  
Multi-functional tablets (Tabs)  
This option optimises washing and drying results.  
When using multi-functional tablets, press the MULTI-  
FUNCTIONAL TABLETS button. The corresponding indicator light  
will illuminate. The “Multi-functional tablets” option results in the  
lengthening of the wash cycle.  
To deselect an option which has been set by mis-  
take, press the corresponding button again.  
Delay Start  
The start of the wash cycle may be delayed for a period of  
time between 1 and 24 hours.  
The MULTI-FUNCTIONAL TABLETS option remains  
set for subsequent wash cycles if it is not deselected.  
1. After selecting the desired wash cycle and any other  
options, press the DELAY START button: the corresponding  
indicator light will illuminate. Use the same button to select  
the time at which you wish the wash cycle to begin (after a  
period of 1 to 24 hours).  
2. Confirm your selection using the Start/Pause button; the  
countdown will begin. The selected delay period indicator  
light is displayed and the Start/Pause button stops flashing  
(the light becomes fixed instead).  
The use of tablets is only recommended for models  
which offer the MULTI-FUNCTIONAL TABLETS option.  
This option is not recommended for use with wash  
cycles which do not specify the use of multi-functional  
tablets (see Table of options).  
This option is incompatible with the following wash cycle:  
Soak.  
3. When the set time has elapsed, a long beep sounds, the  
DELAY START indicator light switches off and the wash  
cycle begins.  
A
Delay  
Start  
B
Half  
Load  
C
Table of options  
To deselect the DELAY START option, press the DELAY  
START button repeatedly until the text OFF appears.  
Tabs  
1. Eco  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
No  
The Delay Start function cannot be set once the wash  
has been started.  
2. Normal  
3. Daily A 60’  
4. Prewash  
5. Intensive  
6. Speed 25’  
7. Delicate  
Yes  
Yes  
Yes  
Yes  
9
 
Wash cycles  
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the  
dishwasher, reduce the amount of detergent used accordingly.  
EN  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
Detergent  
(A) = compartment A  
(B) = compartment B  
Wash  
cycles  
which  
include  
drying  
Wash cycle  
duration  
(tolerance ±10%)  
Hrs. Min.  
Wash cycle selection  
instructions  
Wash cycle  
Options  
Powder  
Liquid  
Tablets  
Environmentally-friendly wash  
cycle with low energy  
consumption levels, suitable for  
pans and dishes.  
1. Eco*  
2. Normal  
3. Daily A 60’  
25 g (A)  
25 ml (A)  
1 (A)  
Yes  
A-B-C  
A-B-C  
A-B-C  
2:50’  
Normally soiled pans and  
dishes. Standard daily wash  
cycle.  
21 g (A)  
4 g (B)  
21 ml (A)  
4 ml (B)  
1 (A)  
1 (A)  
Yes  
No  
1:50’  
1:00’  
Limited quantity of daily soiling.  
(4 place settings + 1 saucepan  
+1 frying pan).  
25 g (A)  
No  
25 ml (A)  
No  
Pre-wash for dishes while  
awaiting completion of the load  
with the dishes from the next  
meal.  
4. Prewash  
5. Intensive  
No  
No  
A-B  
0:08’  
2:25’  
Heavily soiled dishes and pans  
(not to be used for delicate  
items).  
25 g (A)  
25 ml (A)  
1 (A)  
Yes  
A-B-C  
Economic and fast wash to be  
used for lightly soiled dishes.  
(Run cycle immediately after  
use) (2 plates + 2 glasses + 4  
pieces of cutlery + 1 saucepan  
+ 1 small frying pan).  
6. Speed 25’  
7. Delicate  
21 g (A)  
25 g (A)  
21 ml (A)  
25 g (A)  
1 (A)  
1 (A)  
No  
A-C  
0:25’  
1:35’  
Economic and fast wash for  
delicate items which are  
sensitive to high temperatures.  
(Run cycle immediately after  
use) (glasses upper rack +  
delicate plates, lower rack).  
Yes  
A-B-C  
Notes:  
To make it easier to measure out the detergent, it is worth remembering that:  
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid  
Optimum performance levels when using the "Daily and Speed’" cycles can be achieved by observing the maximum amounts of  
crockery specified.  
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less energy  
and is les harmful to the environment.  
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the  
following address: ASSISTENZA_EN_LVS@indesitcompany.com  
10  
 
Rinse aid and refined salt  
repeatedly until the desired hardness level has been reached  
(1-2-3-4-5* see Water hardness table), up to a maximum of five  
levels.  
- To exit the function, wait a few seconds or press one of the  
option buttons*, or switch off the machine using the ON/OFF  
button.  
Only use products which have been specifically  
designed for dishwashers.  
Do not use table salt or industrial salt, or washing  
up liquid.  
EN  
Follow the instructions given on the packaging.  
Even if using multi-functional tablets, the salt dispenser should  
still be filled.  
If using a multi-functional product it is not necessary to add  
rinse aid; however, we recommend that you add salt, especially  
if you live in an area where the water is hard or very hard.  
Follow the instructions given on the packaging.  
Average salt container  
Water Hardness Table  
capacity duration**  
If you do not add salt or rinse aid, the LOW  
SALT* and LOW RINSE AID* indicator lights remain  
lit.  
Level  
°dH  
0 - 6  
°fH  
mmol/l  
0 - 1  
months  
7 months  
5 months  
3 months  
2 months  
1
0 - 10  
11 - 20  
12 - 17 21 - 30  
17 - 34 31 - 60  
2
3
4
6 - 11  
1,1 - 2  
2,1 - 3  
3,1 - 6  
Measuring out the rinse aid  
Rinse aid makes it easier for the crockery to dry, as water runs  
off surfaces more readily and therefore does not leave streaks or  
marks.  
The rinse aid dispenser should be filled:  
• When the LOW RINSE AID*indicator light on the control  
panel is illuminated;  
5*  
34 - 50 61 - 90  
6,1 - 9  
2/3 weeks  
For values between 0°f and 10°f, we do not recommend the  
use of salt. * this setting may cause a slight increase in the  
duration of the cycles. ** for 1 wash cycle per day.  
(°dH = hardness measured in German degrees - °f = hardness  
measured in French degrees - mmol/l = millimoles per litre)  
1. Open the dispenser by turning  
the lid (G) in an anticlockwise  
direction.  
2. Pour in the rinse aid, making sure  
it does not overflow from the  
dispenser. If this happens, clean  
the spill immediately with a dry  
cloth.  
3. Screw the lid back on.  
H
Measuring out the refined salt  
In order to achieve the best possible results using a wash cycle,  
make sure that the dispenser is never empty. Refined salt removes  
limescale from the water, thus avoiding the formation of deposits  
on crockery.  
F
The salt dispenser is located in the lower part of the dishwasher  
(see Description) and should be filled:  
G
• When the green float*cannot be seen by simply looking at the  
cap of the salt dispenser.  
NEVER pour the rinse aid directly  
into the appliance tub.  
• When the LOW SALT* indicator light on the control panel is  
illuminated;  
Adjusting the amount of rinse aid  
1. Remove the lower rack and unscrew the  
container cap (anticlockwise).  
2. The first time you do this: fill the water  
If you are not completely satisfied with the drying results, you  
may adjust the quantity of rinse aid used. Use a screwdriver to  
turn the dosage adjuster (F) to one of the 6 pre-set positions (the  
default position is set to 4):  
tank right up to its edge.  
3. Position the funnel* (see figure) and fill  
the salt container right up to its edge (this  
• If there are streaks on the crockery, set the adjustment device  
to a lower number (1-3).  
should hold approximately 1 kg); it is not unusual for a little water  
to leak out.  
• If drops of water remain on the crockery or if there are limescale  
marks present after the cycle has finished, set the adjuster to a  
higher number (4-6).  
4. Remove the funnel* and wipe any salt residue away from the  
opening; rinse the cap under running water and then screw it on,  
the head facing downwards so as to let the water flow out of the  
four cracks which are arranged in a star shape on the lower part  
of the cap. (the container cap with the green float*)  
It is advisable to perform this procedure every time you add  
salt to the container.  
Setting the water hardness  
Every dishwasher is equipped with a water softener which, by  
using refined salt designed especially for this type of appliance,  
supplies water without limescale which is then used to wash the  
crockery.  
Make sure the cap is screwed on tightly, so that no detergent  
can get into the container during the wash cycle (this could  
damage the water softener beyond repair).  
This dishwasher offers a setting which helps to reduce pollution  
and optimises washing performance in accordance with the water  
hardness level in your area. This information can be obtained  
from the organisation which supplies your household with water.  
- Switch on the appliance by pressing the ON/OFF button.  
- Press the P button and hold for approximately 5 seconds; two  
short beeps will sound, the text H2O will appear on the display  
and the set hardness number will flash (the water softening  
system is set by default to number 3). Press the P button  
When necessary, measure out the salt before a wash cycle  
so that any saline solution which has leaked out of the salt  
dispenser is removed.  
* Only available in selected models.  
11  
 
Care and maintenance  
Shutting off the water and electricity  
supplies  
Clean the water inlet filter at the tap outlet regularly.  
- Turn off the water tap.  
- Unscrew the end of the water inlet hose, remove the filter  
and clean it carefully under running water.  
- Replace the filter and screw the water hose back into  
position.  
EN  
Turn off the water tap after every wash cycle to avoid  
leaks.  
Always unplug the appliance when cleaning it and when  
performing maintenance work.  
Cleaning the filters  
Cleaning the dishwasher  
The filter assembly consists of three filters which remove  
food residues from the washing water and then recirculate  
the water. They should be cleaned if you wish to achieve  
the best results in every wash.  
The external surfaces of the machine and the control  
panel may be cleaned using a non-abrasive cloth which  
has been dampened with water. Do not use solvents or  
abrasive products.  
Clean the filters regularly.  
Any marks on the inside of the appliance may be  
removed using a cloth dampened with water and a little  
vinegar.  
The dishwasher should not be used without filters, or if  
the filter is loose.  
• After several washes, check the filter assembly and if  
necessary clean it thoroughly under running water, using  
a non-metallic brush and following the instructions below:  
1. Turn the cylindrical filter C in an anti-clockwise direction  
and pull it out (fig. 1).  
2. Remove the cup filter B by exerting a slight pressure on  
the side flaps (fig. 2).  
3. Slide out the stainless steel plate filter A (fig. 3).  
4. Inspect the trap and remove any food residue. NEVER  
REMOVE the wash cycle pump (black detail) (fig. 4).  
Preventing unpleasant odours  
Always keep the door of the appliance ajar in order to  
avoid moisture from forming and being trapped inside  
the machine.  
Clean the seals around the door and detergent  
dispensers regularly using a damp sponge. This will  
avoid food becoming trapped in the seals, which is the  
main cause behind the formation of unpleasant odours.  
Cleaning the sprayer arms  
Food residue may become encrusted onto the sprayer arms  
and block the holes used to spray the water. It is therefore  
recommended that the arms are checked from time to time  
and cleaned with a small non-metallic brush.  
B
C
The two sprayer arms may both be removed.  
C
To remove the upper sprayer  
arm, rotate the locking ring in  
an anti-clockwise direction.  
The upper sprayer arm should  
be replaced with the holes  
facing upwards.  
1
2
A
The lower sprayer arm can be  
removed by pulling it upwards.  
4
3
After cleaning the filters, replace the filter assembly and fix  
it in position correctly; this is essential for maintaining the  
efficient operation of the dishwasher.  
Leaving the machine unused for extended  
periods  
Disconnect the appliance from the electricity supply  
and shut off the water tap.  
Cleaning the water inlet filter*  
If the water hoses are new or have not been used for an  
extended period of time, let the water run to make sure it is  
clear and free of impurities before performing the necessary  
connections. If this precaution is not taken, the water inlet  
could become blocked and damage the dishwasher.  
Leave the door of the appliance ajar.  
• When you return, run a wash cycle when the dishwasher  
is empty.  
* Only available in selected models.  
12  
 
Precautions and advice  
The appliance was designed and manufactured in  
compliance with current international safety standards. The  
following information has been provided for safety reasons and  
should therefore be read carefully.  
Saving energy and respecting the  
EN  
environment  
Saving water and energy  
Only start a wash cycle when the dishwasher is full. While  
waiting for the dishwasher to be filled, prevent unpleasant  
odours with the Soak cycle (see Wash Cycles).  
General safety  
This appliance is not intended for use by persons (including  
children) with reduced physical, sensory or mental  
capabilities, or lack of experience and knowledge, unless  
they have been given supervision or instruction concerning  
use of the appliance by a person responsible for their safety.  
Children should be supervised to ensure that they do not  
play with the appliance.  
The appliance was designed for domestic use inside the  
home and is not intended for commercial or industrial use.  
The appliance must be used by adults only, to wash domestic  
crockery according to the instructions in this manual.  
The appliance must not be installed outdoors, even in covered  
areas. It is extremely dangerous to leave the machine  
exposed to rain and storms.  
Select a wash cycle that is suited to the type of crockery and  
to the soil level of the crockery using the Wash cycle table:  
- for dishes with a normal soil level, use the Eco wash cycle,  
which guarantees low energy and water consumption levels.  
- if the load is smaller than usual activate the Half load*option  
(see Start-up and use).  
If your electricity supply contract gives details of electricity  
saving time bands, run wash cycles during the periods when  
a lower tariff is applied. The Delayed start*button (see Start-  
up and use) helps you organise the wash cycles accordingly.  
Do not touch the appliance when barefoot.  
When unplugging the appliance always pull the plug from the  
mains socket, do not pull on the cable.  
Phosphate-free and chlorine-free detergents  
containing enzymes  
The water supply tap must be shut off and the plug should  
be removed from the electrical socket before cleaning the  
appliance or carrying out any maintenance work.  
If the appliance breaks down, do not under any  
circumstances touch the internal parts in an attempt to carry  
out the repair work yourself.  
Never touch the heating element.  
Do not lean or sit on the open door of the appliance: this may  
cause the appliance to overturn.  
The door should not be left open as it may create a dangerous  
obstacle.  
The packaging material should not be used as a toy: it can  
become a choking or suffocation hazard.  
We strongly recommend that you use detergents that do not  
contain phosphates or chlorine, as these products are harmful  
to the environment.  
Enzymes provide a particularly effective action at  
temperatures around 50°C, and as a result detergents  
containing enzymes can be used in conjunction with low-  
temperature wash cycles in order to achieve the same results  
as a normal 65°C wash cycle.  
To avoid wasting detergent, use the product in appropriate  
quantities based on the manufacturer’s recommendations,  
the hardness of the water and the soil level and quantity of  
the crockery. Even if they are biodegradable, detergents  
contain substances that may alter the balance of nature.  
If your family includes children:  
• DO NOT allow children to play with the appliance or tamper with  
its controls.  
• Keep detergents and rinse aids away from children.  
• Keep children away from the open door of a dishwasher, there  
could still be some detergent left inside.  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to helping the  
environment, Hotpoint reserves the right to use quality recycled  
components to keep down customer costs and minimise material  
wastage.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical and  
Electronic Equipment (WEEE), requires that old household  
electrical appliances must not be disposed of in the normal  
unsorted municipal waste stream. Old appliances must be  
collected separately in order to optimise the recovery and  
recycling of the materials they contain and reduce the impact on  
human health and the environment. The crossed out "wheeled  
bin" symbol on the product reminds you of your obligation, that  
when you dispose of the appliance it must be separately collected.  
Please dispose of packaging and old appliances carefully.  
To minimise risk of injury to children, remove the door, plug and  
cut mains cable off flush with the appliance. Dispose of these  
parts separately to ensure that the appliance can no longer be  
plugged into a mains socket and the door cannot be locked shut.  
Consumers should contact their local authority or retailer for  
information concerning the correct disposal of their old appliance.  
* Only available in selected models.  
13  
 
Troubleshooting  
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance (see Assistance).  
EN  
Problem:  
Possible causes / Solutions:  
The dishwasher does not start or  
cannot be controlled  
• Switch off the appliance by pressing the ON/OFF button, switch it back on after  
approximately one minute and reset the program.  
• The appliance has not been plugged in properly.  
• The dishwasher door has not been shut properly.  
The door won’t close  
• The lock was released. Strongly push the door until a “clacking” noise is heard.  
No water drains out from the  
dishwasher.  
• The dishwasher cycle has not yet finished.  
• The water inlet hose is bent (see Installation).  
• The drain duct is blocked.  
• The filter is clogged up with food residues.  
The dishwasher makes excessive  
noise.  
• The dishes are rattling against each other or against the sprayer arms.  
• An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up and  
use).  
The dishes and glasses are  
covered in a white film or  
limescale deposits.  
• The level of the refined salt is low or the dosage setting is not suited to the hardness  
of the water (see Rinse aid and salt).  
• The lid on the salt dispenser is not closed properly.  
• The rinse aid has been used up or the dosage is too low.  
The dishes and glasses are  
• The rinse aid dosage is too high.  
streaked or have a bluish tinge.  
The crockery has not been dried  
properly.  
• A wash cycle without a drying program has been selected.  
• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).  
• The rinse aid dispenser setting is not suitable.  
• The crockery is made from non-stick material or plastic.  
The dishes are not clean.  
• The racks are overloaded (see Loading the racks).  
• The crockery has not been arranged well.  
• The sprayer arms cannot move freely.  
• The wash cycle is too gentle (see Wash cycles).  
• An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up and  
use).  
• The lid on the rinse aid compartment has not been shut correctly.  
• The filter is dirty or blocked (see Care and maintenance).  
• The refined salt level is low (see Rinse aid and salt).  
The dishwasher does not take any • There is no water in the mains supply.  
water in - Tap shut-off alarm  
• The water inlet hose is bent (see Installation).  
• Turn on the tap and the appliance will start after a few minutes.  
• The appliance lock has been activated because no action was taken when the  
(the display shows A 6).  
beeps* sounded.  
Switch off the appliance using the ON/OFF button, turn on the tap and switch the  
appliance back on after 20 seconds by pressing the same button. Re-program the  
appliance and restart the wash cycle.  
Water inlet hose alarm / Water inlet • Switch off the appliance by pressing the ON/OFF button. Shut off the water tap to  
filter blocked  
(the display shows A 7).  
eliminate the risk of flooding and remove the plug from the electrical socket.  
Make sure the water inlet filter has not become blocked by impurities (see “Care  
and maintenance” chapter).  
14  
 
After Sales Service  
After Sales Service  
Appliance Registration  
EN  
No one is better placed to care for your Hotpoint  
appliance during the course of its working life  
than us - the manufacturer.  
We want to give you additional benefits of Hotpoint  
ownership. To activate your free 5 year parts guarantee  
you must register your appliance with us.  
UK: 08448 24 24 24  
Essential Contact Information  
Republic of Ireland: 01 230 0800  
Hotpoint Service  
We are the largest service team in the country offering  
you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive  
fast, reliable, local service.  
Indesit Company UK Ltd. Morley Way, Peterborough,  
PE2 9JB  
Indesit Company Unit 49 Airways Industrial  
Estate,Dublin 17  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Recycling and Disposal Information  
Please note: Our advisors will require the  
following information:  
As part of Hotpoint's continued commitment to helping  
the environment, Hotpoint reserves the right to use  
quality recycled components to keep down customer  
costs and minimise material wastage.  
Model number:  
Please dispose of packaging and old appliances  
carefully.  
Serial number:  
To minimise risk of injury to children, remove the door,  
plug and cut mains cable off flush with the appliance.  
Dispose of these parts separately to ensure that the  
appliance can no longer be plugged into a mains socket  
and the door cannot be locked shut.  
Parts and Accessories  
We supply a full range of genuine replacement parts  
as well as accessory products that protect and  
hygienically clean your appliance to keep it looking  
good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
15  
 
Guarantee  
195106209.01  
09/2012 pb - Xerox Fabriano  
Guarantee  
EN  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because  
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to  
you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,  
batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will be a  
charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (Republic of Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense of  
repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226  
(Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to  
arrange for an engineer to call.  
16  
 

Grizzly Grinder G0596 User Manual
Haier Water Heater ES10V M1 User Manual
Harbor Freight Tools Motorcycle 91764 User Manual
Heath Zenith Work Light PF 4291 BK User Manual
Hotpoint Cooktop CEO 647 Z User Manual
HP Hewlett Packard PDAs Smartphones 364351 202 User Manual
HP Hewlett Packard Portable Media Storage WDBW2A0020HBK NESN User Manual
HP Hewlett Packard Power Supply H7421A User Manual
HP Hewlett Packard Switch 3 User Manual
HP Hewlett Packard Wireless Office Headset 332630 005 User Manual