Hotpoint Dishwasher FDUD4212 User Manual

Instruction booklet  
DISHWASHER  
Contents  
EN  
Installation, 2-5  
Positioning and levelling  
Technical data  
English, 1  
Electrical connection  
Connecting the water supply  
Description of the appliance, 6  
Overall view  
Control panel  
Loading the racks, 7  
Lower rack  
Cutlery basket  
Upper rack  
Start-up and use, 8-9  
Starting the dishwasher  
Loading the detergent  
Washing options  
DUD 4212  
Wash cycles, 10  
Wash cycle table  
Rinse aid and refined salt, 11  
Loading the rinse aid  
Loading the refined salt  
Care and maintenance, 12  
Shutting off the water and electricity supplies  
Cleaning the dishwasher  
Preventing unpleasant odours  
Cleaning the sprayer arms  
Cleaning the water inlet filter  
Cleaning the filters  
Leaving the machine unused for extended periods  
Precautions and advice, 13  
General safety  
Disposal  
Saving energy and respecting the environment  
Troubleshooting, 14  
After Sales Service, 15  
After Sales Service  
Essential Contact Information  
Parts and Accessories  
Appliance Registration  
Hotpoint Guarantee, 16  
 
The dishwasher meets the requirements set out by  
the regulations in force concerning safety and electrical  
equipment.  
Changing the Plug  
EN  
Cut off and dispose of the supplied plug if it does not  
fit your socket.  
Any technical checks should be conducted  
exclusively by a trained and authorised technician:  
Repairs carried out by unaithorised persons will  
invalidate the guarantee, as well as posing a potential  
hazard to the user.  
To avoid a shock hazard DO NOT insert the  
discarded plug into a socket anywhere else.  
Wires in the mains lead are coloured accordance  
with the following code:  
The manufacturer declines all responsibility for  
damage to persons or property resulting from failure to  
observe the above precautions, from tampering with  
even a single component or from the use of non-original  
spare parts.  
Green/Yellow -  
Earth  
Neutral  
Live  
Blue  
-
-
Brown  
If you change the plug, the colour of the wires in the  
mains lead may not correspond with the terminal  
markings in the plug, which if not coloured, could be:  
Electrical Connection  
Before inserting the plug into the electrical socket, make  
sure that:  
EARTH  
NEUTRAL ‘N’  
LIVE ‘L’  
‘E’ or  
the socket is earthed and complies with current  
regulations;  
the socket can withstand the maximum load of the  
appliance, which is indicated on the data plate  
located on the inside of the door (see Description of  
the appliance);  
Changing the Mains Lead  
A lead can be ordered from Hotpoint Service  
UK: 08709 066 066 or  
the power supply voltage falls within the values  
Republic of Ireland: 1850 302 220  
indicated on the data plate on the inside of the door;  
- If you have damaged the existing lead or require a  
longer one a charge will be made. It is strongly advised  
that this work is carried out by a qualified electrician.  
- If the domestic wiring includes a residual current-  
operated circuit breaker, ensure that it conforms to the  
latest regulations.  
the socket is compatible with the plug of the  
appliance. If this is not the case, ask an authorised  
technician to replace the plug (see After Sales  
Service); do not use extension cables or multiple  
sockets.  
The dishwasher must not be connected to the  
electricity supply while installation is being carried out.  
- This appliance should only be connected to a 230/  
240V AC source, via a properly installed earthed socket.  
- Use the dishwasher solely in a domestic environment.  
- DO NOT stand or place heavy objects on the door  
when it is open, this could damage the door or cause the  
appliance to tip forward.  
Once the appliance has been installed, the power  
supply cable and the electrical socket should be easily  
accessible.  
The cable should not be bent or compressed.  
If the power supply cable is damaged, it must be  
replaced by the manufacturer or its Technical  
Assistance Service in order to prevent all potential  
hazards. (See After Sales Service)  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not  
observed.  
This appliance must be earthed  
6uses:your appliance comes fitted with a plug and a 13A  
fuse. If you need to replace the fuse, only those rated at  
13A and ASTA approved to BS1362 should be used. If  
you lose the fuse cover, a replacement may be obtained  
from your local authorised Service Centre or Electrical  
company. Correct replacement is identified by colour  
coding or the marking on base of plug.  
DO NOT use the plug unless the fuse cover is fitted.  
3
 
Connecting the water supplies  
Sink Waste System  
Connect the outlet hose (without bending it) to a drain  
EN  
Connection to the water and electricity supplies  
should only be performed by a qualified technician.  
duct with a minimum diameter of 32 mm.  
The dishwasher should not stand on top of the water  
hoses or the electricity supply cable.  
Connecting the water inlet hose  
The water inlet and outlet hoses and the electricity  
supply cable may be positioned towards the right or the  
left in order to achieve the best possible installation.  
To a suitable cold water connection point: before  
attaching the hose, run the water until it is perfectly  
clear so that any impurities that may be present in the  
water do not clog the appliance; after performing this  
operation, screw the inlet hose tightly onto a tap with  
a ¾ gas threaded connection.  
The outlet hose must be at a height ranging from 40 to  
80 cm (from 15’’ to 31’’) from the floor / surface where  
the dishwasher rests (A).  
• before connecting the drain hose, remove any  
internal restrictions; this will prevent a build up of  
debris which could cause a blockage  
To a suitable hot water connection point: your  
dishwasher may be provided with hot water from the  
mains supply (if you have a central heating system  
with radiators) provided that it does not exceed a  
temperature of 60°C.  
• remove any restrictions from the waste spigot and  
ensure that the sealing bung is removed (B).  
Screw the hose to the tap as described for  
connection to a cold water supply.  
It MUST NOT be connected to a surface water drain.  
If the inlet hose is not long enough, contact a  
• Untie the end of the GREY drainage hose from the rear  
of the appliance.  
specialist store or an authorised technician (see After  
Sales Service).  
• If fitting an under sink  
waste disposal unit, cut  
out the membrane, bung  
or blanking plug.  
The water pressure must be within the values  
indicated in the Technical data table (see Installation).  
The hose should not be bent or compressed.  
The appliance must be connected to the water  
supply network using new hoses.  
Do not use old hoses.  
Ensure the drain hose is securely attached, to  
prevent it coming away while the machine is in use and  
causing a flood.  
Ensure that the new hose supplied is connected and the  
old hose is disposed of safely.  
DO NOT overtighten the hose connector, hand tight  
is sufficient.  
6it hose to waste securely using a “Jubilee” type  
clip.  
Ensure the fill hose is not kinked.  
Tap connections*: A range of adaptors are available  
to suit your tap.  
DO NOT connect the dishwasher to a single outlet  
instantaneous water heater or an electric heater.  
* Only available in selected models.  
4
 
Anti-flooding protection*  
EN  
To ensure floods do not occur, the dishwasher:  
- is provided with a special system which blocks the  
water supply in the event of anomalies or leaks from  
inside the appliance.  
Some models are also equipped with the supplementary  
safety device New Acqua Stop*, which guarantees anti-  
flooding protection even in the event of a supply hose  
rupture.  
WARNING: HAZARDOUS VOLTAGE!  
Under no circumstance should the water inlet hose be  
cut as it contains live electrical parts.  
The Company shall not be held responsible for any  
incidents that occur if these regulations are not  
observed.  
* Only available in selected models.  
5
 
Description of the appliance  
Overall view  
EN  
1.  
Upper rack  
2.  
Upper sprayer arm  
Tip-up compartments  
Rack height adjuster  
Lower rack  
3.  
4.  
5.  
6.  
Lower sprayer arm  
Cutlery basket  
7.  
8.  
Washing filter  
9.  
Salt dispenser  
10.  
11.  
12.  
13.  
Detergent and rinse aid dispensers  
Data plate  
Control panel***  
Locking ring  
Control panel  
Short Time option  
indicator light  
Good Night option indicator light  
Extra Dry indicator light  
Multi-functional tablets  
indicator light  
Low salt  
indicator light  
Wash cycle name  
indicator light  
Half load upper and lower  
rack indicator lights  
Select wash  
cycle button  
ON/Oꢀꢀ  
indicator light  
Time remaining  
light-up display  
Start/Pause  
button and  
indicator light  
ON/Oꢀꢀ/Reset  
button  
Delayed start  
indicator light  
Multi-functional tablets  
button  
Low rinse aid  
indicator light  
Delayed start  
button  
Option button  
Short Time  
Half load button  
Good Night  
option button  
Extra Dry button  
***Only in completely built-in models.  
*Only available in selected models.  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
6
 
Loading the racks  
Before loading the racks, remove all food residue from  
crockery and empty liquids from glasses and cups.  
After loading the appliance, make sure that the sprayer  
arms can rotate freely.  
Upper rack  
Load this rack with delicate and lightweight crockery: glasses,  
EN  
cups, saucers and shallow salad bowls.  
Lower rack and cutlery basket  
Thelowerrackcanholdpans, lids, plates, saladbowls, cutlery, etc.  
Large plates and lids should ideally be placed at the sides of the rack.  
Adjustable position tip-up compartments  
The tip-up compartments  
can be positioned at  
different heights, to optimise  
the arrangement of crockery  
throughout the rack. Wine  
glasses can be placed  
Several dishwasher models are fitted with tip-up sections*,  
which can be used in a vertical position when arranging plates  
or in a horizontal position when arranging saucepans, salad  
bowls and frying pans.  
safely in the tip-up  
compartments, by inserting  
the stem of each glass into  
the corresponding slots.  
Some dishwasher models are fitted  
with a sliding tray*which can be  
used to hold serving utensils or small  
cups. 'or optimum washing  
performance, avoid positioning bulky  
crockery directly below the tray.  
Adjusting the height of the upper rack  
In order to make it easier to arrange the crockery, the upper  
rack may be moved to a higher or lower level.  
The type of cutlery basket may vary (modular or non-modular)  
according to the dishwasher model. The non-modular basket must  
only be positioned at the front of the lower rack.  
The height of the upper rack should ideally be adjusted  
WHEN THE RACK IS EMPTY.  
NEVER raise or lower the rack on one side only.  
Open the left and right guide rail stops and  
pull out the rack; position it higher or lower  
as required, slide it along the guide rails  
until the front wheels are in place and close  
the stops (see figure).  
Both are fitted  
with grilles over  
the top, for  
If the rack is fitted with Dual Space  
handles*(see figure), pull out the upper  
rack until it reaches its stop point, grip the  
handles at the sides of the rack and move  
it upwards or downwards, then slowly let it  
fall back into place.  
improved cutlery  
arrangement.  
Knives and other utensils with sharp edges must be  
placed in the cutlery basket with the points facing downwards,  
or they must be positioned horizontally in the tip-up  
compartments on the upper rack.  
Items that should not be washed in the dishwasher  
Wooden items, objects with wooden or horn handles or  
glued-on parts.  
Items made from aluminium, copper, brass, pewter or tin.  
Items made from plastic material which is not heat-resistant.  
Antique or hand-painted porcelain.  
Antique silver. Silver that is not antique may, however, be  
washed in the dishwasher using a delicate wash cycle,  
provided that it does not come into contact with other metals.  
* Only available in selected models. The number and position  
We recommend the use of crockery which is dishwasher  
may vary.  
safe.  
7
 
Start-up and use  
prolonged beep is emitted.  
Switching the appliance on for the first time  
EN  
If the Start/Pause button is pressed so as to pause the  
machine, the wash cycle or the Delayed Start function (if  
selected) is interrupted.  
Selecting the language  
Press the ON/O'' button, you will hear a short beep and the  
display will show the set language.  
At this stage it is not possible to change the wash cycle.  
Use the DELAYED START button to scroll forwards, or the HAL'  
LOAD button to scroll backwards through the list until you reach  
the desired language. Press the P button to confirm the selection;  
you will then automatically enter the list of wash cycles.  
Every time the dishwasher is switched on subsequently, the list  
of wash cycles will be displayed.  
Accidental interruptions  
If the door is opened during the wash cycle, or if there is a  
power cut, the cycle stops. It starts again from the point at  
which it was interrupted once the door has been shut or once  
the electricity supply is restored.  
The language may also be changed at a later date, by pressing  
the P button and the DELAYED START button simultaneously for  
a few seconds.  
Measuring out the detergent  
A good wash result also depends on the correct amount of  
detergent being used; exceeding the stated amount does  
not result in a more effective wash and increases  
environmental pollution.  
Starting the dishwasher  
1. Turn the water tap on.  
2. Press the ON/O'' button: you will hear a short beep and  
the display will light up.  
Only use detergent which has been specifically  
designed for dishwashers.  
3. Open the door and pour in a suitable amount of detergent  
(see below).  
DO NOT USE washing up liquid.  
4. Load the racks (see Loading the racks) and shut the door.  
5. Select the wash cycle in accordance with the type of  
crockery and its soil level (see Table of wash cycles) by  
pressing the P button.  
Using excessive detergent may result in foam residue  
remaining in the machine after the cycle has ended.  
To achieve the best results from each washing and  
drying cycle, powder detergent, rinse aid liquid and salt  
should be used.  
6. Select the wash options (see adjacent information).  
7. Start the cycle by pressing the Start button: a long beep  
signals the start of the wash cycle; the name of the selected  
cycle is displayed, along with the time remaining until the end  
of the cycle.  
Compartment A: Washing detergent  
Compartment B: Pre-wash detergent  
8. Two short beeps and one long one indicate the end of the  
wash cycle and the text “END O' CYCLE” appears on the  
display. Switch off the appliance by pressing the ON/O''  
button, shut off the water valve and unplug the appliance from  
the electricity socket.  
1. Open cover C by pressing button D.  
D
A
B
2. Pour in the detergent after consulting  
the Table of wash cycles:  
• 'or powder detergent use  
compartments A and B.  
9. Wait for a few minutes before removing the crockery, in  
order to avoid burns. Unload the racks, beginning with the  
lower level.  
• 'or detergent in tablet form: when the  
cycle requires 1 tablet, place it in  
compartment A and close the cover;  
C
when it requires 2, place the second tablet at the bottom of the  
appliance.  
AUTO WASH CYCLES*:this model of dishwasher is  
equipped with a special sensor which can be used to assess  
the level of soiling and automatically select the most efficient  
and economic wash cycle accordingly.  
3. Remove detergent residues from the edges of the  
compartment and close the cover until it clicks.  
The duration of the auto wash cycles may vary due to the  
operation of the sensor.  
Wash options*  
The OPTIONS may only be set, modified or reset after the  
wash cycle has been selected and before the Start/  
Pause button has been pressed.  
- The machine will switch off automatically  
during certain periods of inactivity, in order to  
minimise electricity consumption.  
Only the options which are compatible with the type of wash  
cycle set may be selected. If an option is not compatible with the  
selected wash cycle (see Table of wash cycles), the corre-  
sponding LED flashes rapidly 3 times and 2 short beeps will  
sound.  
Modifying a wash cycle in progress  
If a mistake was made during the wash cycle selection  
process it is possible to change the cycle, provided that it has  
only just begun: once the wash cycle has started, switch off  
the machine by pressing and holding the ON/O''/Reset  
button. Switch it back on using the same button and select the  
desired wash cycle and options.  
If an option is selected which is incompatible with another (previ-  
ously selected) option, the indicator light corresponding to the  
option selected first will flash 3 times, 3 beeps will sound and it will  
be deselected, while the most recently selected option will remain  
active.  
Adding extra crockery  
Press the Start/Pause button (the corresponding indicator light  
will flash). Open the door, taking care to avoid the escaping  
steam, and place the crockery inside the appliance. Press the  
Start/Pause button (fixed light): the cycle will restart after a  
To deselect an option which has been set by mistake, press the  
corresponding button again.  
*Only available in selected models.  
8
 
The Short Time and Good Night options are not  
compatible with each other.  
Half load using the upper or lower rack  
If there are not many dishes to be washed, a half load cycle  
may be used in order to save water, electricity and detergent.  
Select the wash cycle and press the HAL' LOAD button  
repeatedly: the triangle corresponding to the selected load will  
illuminate and the wash cycle will take place only using the  
upper or lower rack. If the button is pressed again, the option  
will be deselected.  
EN  
The Short Time and Good Night options are not  
compatible with the HAL, LOAD option.  
Multi-functional tablets  
This option optimises washing and drying results.  
When using multi-functional tablets, press the MULTI-  
'UNCTIONAL TABLETS button; the corresponding indicator  
light will illuminate. If the button is pressed again the option will  
be deselected.  
The Half Load option is not compatible with the Good  
Night and Short Time options.  
Remember to load the upper or lower rack only, and  
to reduce the amount of detergent accordingly.  
The “Multi-functional tablets” option results in the  
lengthening of the wash cycle.  
It is better to use powder detergent in this case.  
The MULTI-7UNCTIONAL TABLETS option remains set  
for subsequent wash cycles if it is not deselected.  
This option is incompatible with the following wash  
cycle: Speed wash.  
The use of tablets is only recommended when the MULTI-  
7UNCTIONAL TABLETS option is available.  
Delayed start  
It is possible to delay the start time of the cycle for a period of  
time between 1 and 24 hours.  
This option is not recommended for use with wash cycles  
which do not specify the use of multi-functional tablets  
(see Table of options).  
1. After selecting the desired wash cycle and any other options,  
press the DELAYED START button. The Delayed Start symbol  
will begin to flash. Use the same button to select the time at which  
you wish the wash cycle to begin (after a period of 1 to 24  
hours).  
Extra drying  
To improve the dryness level of the crockery, press the  
EXTRA DRYING button; the indicator light will illuminate. If it is  
pressed again the option will be deselected.  
2. Confirm the selection using the START/PAUSE button;  
the symbol will stop flashing and the countdown will begin.  
The text “START INꢀ” will be displayed, the selected de-  
lay time will flash and the START/PAUSE button will remain  
lit in a fixed manner.  
The EXTRA DRYING option increases the duration of  
the wash cycle.  
SEL<CARE WASH CYCLE  
This disinfecting wash cycle deep cleans the inside of the  
dishwasher, thereby reducing the formation of bad odours.  
3. When the set time has elapsed, a long beep sounds, the  
DELAYED START indicator light switches off and the wash  
cycle begins.  
To deselect the DELAYED START option, press the DELAYED  
START button repeatedly until the text O7appears.  
WARNING  
The SEL7CARE wash cycle should be performed as part of  
your dishwasher maintenance routine, using special single-  
dose products (follow the instructions on the packaging)  
while the dishwasher is EMPTY.  
The Delayed Start function cannot be set once a wash  
cycle has been started.  
Short Time option  
This option can be used to reduce the duration of the main wash  
cycles while maintaining the same washing and drying perfor-  
mance levels.  
Table of options*  
After selecting the wash cycle, press the Short Time option but-  
ton; the illumination of the corresponding indicator light followed  
by a short beep indicates its selection.  
A
B
Half  
Load  
C
D
E
F
Delayed  
Start  
Extra Short Good  
Tabs  
Dry  
Yes  
Yes  
No  
Time Night  
To deselect the option, press the same button again.  
Auto Super wash  
Normal  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
No  
No  
No  
No  
No  
Yes  
No  
No  
No  
No  
No  
Yes  
No  
No  
Yes  
No  
No  
No  
No  
No  
No  
No  
Good Night option  
Daily A 60’  
Soaking  
This option reduces the amount of noise made by the machine  
and lengthens the wash cycles. It is a useful option because it  
enables users to benefit from the night-time energy rate.  
After selecting the wash cycle, press the Good Night option  
button; the illumination of the corresponding indicator light fol-  
lowed by a short beep indicates its selection.  
No  
Eco 50°C  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
NO  
Yes  
Yes  
Yes  
Yes  
No  
Speed 25’  
Crystals  
Yes  
No  
To deselect the option, press the same button again.  
Auto Duo Wash  
Ultra Intensive  
Special Guest  
Baby Cycle  
Self Care  
Yes  
Yes  
No  
No  
No  
No  
No  
*Only available in selected models.  
9
 
Wash cycles  
The number and type of wash cycles and options may vary depending on the dishwasher model.  
EN  
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce  
the amount of detergent used accordingly.  
Detergent  
(A) = compartment A  
(B) = compartment B  
Wash  
cycles  
which  
include  
drying  
Wash cycle  
duration  
(tolerance  
±10%)  
Wash cycle selection instructions  
Wash cycle  
Options  
Powder  
Liquid  
Tablets  
Hrs. Min.  
Heavily soiled dishes and pans (not to  
be used for delicate items).  
Auto  
Super Wash  
35 g (A) 35 ml (A)  
29 g (A) 29 ml (A)  
1 (A)  
Yes  
Yes  
A-B-C-D-E  
2:25’  
1:50’  
Normally soiled pans and dishes.  
Standard daily wash cycle.  
A-B-C-D-E-  
F
1 (A)  
1 (A)  
No  
Normal  
6 g (B)  
6 ml (B)  
Limited quantity of daily soiling.  
(4 place settings + 1 saucepan +1 frying  
pan).  
Daily A 60’  
25 g (A) 25 ml (A)  
A-B-C  
A B  
1:00’  
0:08’  
3:00’  
No  
No  
Pre-wash for dishes while awaiting  
completion of the load with the dishes  
from the next meal.  
Soaking  
No  
No  
Environmentally-friendly wash cycle with  
low energy consumption levels, suitable  
for pans and dishes.  
29 g (A) 29 ml (A)  
6 g (B) 6 ml (B)  
Eco* 50° C  
Yes  
1 (A)  
AB-C-D-F  
Economic and fast wash to be used for  
lightly soiled dishes. (Run cycle  
immediately after use) (2 plates + 2  
glasses + 4 pieces of cutlery + 1  
saucepan + 1 small frying pan).  
Speed 25’  
25 g (A) 25 ml (A)  
35 g (A) 35 ml (A)  
1 (A)  
No  
A - C  
0:25’  
Economic and fast wash for delicate  
items which are sensitive to high  
temperatures. (Run cycle immediately  
after use) (glasses upper rack +  
delicate plates, lower rack).  
Crystals  
1 (A)  
1 (A)  
ABC-D  
ACD-E  
1:30’  
1:45’  
Yes  
Yes  
Wash spread over the two racks:  
delicate for crystal and glasses on the  
upper rack and heavy duty for the pans  
on the lower rack.  
Auto  
Duo Wash  
35 g (A) 35 ml (A)  
35 g (A) 35 ml (A)  
1 (A)  
1 (bottom  
of the  
Heavily soiled saucepans or pans with  
residual dried-on food.  
Ultra Intensive  
Special Guest  
A B C-D  
AB D  
2:35'  
Yes  
Yes  
5 g (B)  
5 ml (B)  
appliance)  
Rinse and drying cycle for dishes that  
are seldom used and are only dusty.  
No  
No  
No  
No  
0:32’  
Disinfecting wash cycle suitable for  
washing bottles, rings and teats together  
with plates, cups, glasses and cutlery.  
The crockery should only be loaded on  
the upper rack.  
Baby Cycle  
SelfCare  
20 g (A) 20 ml (A)  
Yes  
No  
A
A
1:20'  
0:40'  
Disinfecting cycle for cleaning the inside  
of the dishwasher, to be carried out only  
when the dishwasher is EMPTY using  
specific detergents designed for  
No  
No  
No  
dishwasher maintenance.  
Notes: To make it easier to measure out the detergent, it is worth remembering that:  
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid.  
Optimum performance levels when using the "Daily wash" and "Speed" cycles can be achieved by observing the maximum amounts  
of crockery specified.  
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less  
energy and is les harmful to the environment.  
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the  
following address: [email protected]  
10  
 
Rinse aid and refined salt  
Only use products which have been  
specifically designed for dishwashers.  
Do not use table salt or industrial salt, or  
washing up liquid.  
- Press the DELAYED START button (of 1 to 5) or the HAL7  
EN  
LOAD button (of 5 to 1) repeatedly until the desired  
hardness level has been reached; press the P button to  
confirm. (1-2-3-4-5*see Water hardness table), up to a  
maximum of 5*levels.  
<ollow the instructions given on the packaging.  
- To exit the function, wait approximately few seconds or press  
another option*button, or switch off the machine using the ON/  
O77 button.  
If using a multi-functional product it is not necessary to  
add rinse aid; however, we recommend that you add salt,  
especially if you live in an area where the water is hard or  
very hard. 'ollow the instructions given on the packaging.  
Even if using multi-functional tablets, the salt dispenser should  
still be filled.  
If you do not add salt or rinse aid, the LOW  
SALT* and LOW RINSE AID* indicator lights  
remain lit.  
Average salt container  
Water Hardness Table  
capacity duration**  
Level  
°dH  
°fH  
mmol/l  
0 - 1  
1,1 - 2  
2,1 - 3  
3,1 - 6  
months  
7 months  
5 months  
3 months  
2 months  
1
0 - 6  
0 - 10  
2
3
4
6 - 11 11 - 20  
12 - 17 21 - 30  
17 - 34 31 - 60  
Measuring out the rinse aid  
Rinse aid makes it easier for the crockery to dry, as water  
runs off surfaces more readily and therefore does not leave  
streaks or marks.  
5*  
34 - 50 61 - 90  
6,1 - 9  
2/3 weeks  
For values between 0°f and 10°f, we do not recommend the  
The rinse aid dispenser should be filled:  
• When the LOW RINSE AID*indicator light on the control  
panel is illuminated;  
use of salt.  
* this setting may cause a slight increase in the duration of  
the cycles.  
1. Open the dispenser by turning  
the lid (G) in an anticlockwise  
** for 1 wash cycle per day.  
direction.  
(°dH = hardness measured in German degrees - °f =  
hardness measured in 'rench degrees - mmol/l = millimoles  
per litre)  
2. Pour in the rinse aid, making  
sure it does not overflow from the  
F
dispenser. If this happens, clean  
the spill immediately with a dry  
Measuring out the refined salt  
In order to achieve the best possible results using a wash  
cycle, make sure that the dispenser is never empty. Refined  
salt removes limescale from the water, thus avoiding the  
formation of deposits on crockery.  
G
cloth.  
3. Screw the lid back on.  
NEVER pour the rinse aid directly into the appliance tub.  
Adjusting the amount of rinse aid  
The salt dispenser is located in the lower part of the  
dishwasher (see Description) and should be filled:  
• When the green float*cannot be seen by simply looking at  
the cap of the salt dispenser.  
If you are not completely satisfied with the drying results, you  
may adjust the quantity of rinse aid used. Use a screwdriver  
to turn the dosage adjuster (') to one of the 6 pre-set  
positions (the default position is set to 4):  
• When the LOW SALT*indicator light on the control panel is  
illuminated;  
• If there are streaks on the crockery, set the adjustment  
device to a lower number (1-3).  
1. Remove the lower rack and unscrew the  
• If drops of water remain on the crockery or if there are  
limescale marks present after the cycle has finished, set the  
adjuster to a higher number (4-6).  
container cap (anticlockwise).  
2. The first time you do this: fill the water  
tank right up to its edge.  
3. Position the funnel*(see figure) and fill  
Setting the water hardness  
the salt container right up to its edge (this should hold  
approximately 1 kg); it is not unusual for a little water to leak  
out.  
Every dishwasher is equipped with a water softener which, by  
using refined salt designed especially for this type of  
appliance, supplies water without limescale which is then used  
to wash the crockery.  
4. Remove the funnel* and wipe any salt residue away from the  
opening; rinse the cap under running water and then screw it  
on, the head facing downwards so as to let the water flow out  
of the four cracks which are arranged in a star shape on the  
lower part of the cap. (the container cap with the green float*)  
It is advisable to perform this procedure every time you  
add salt to the container.  
This dishwasher offers a setting which helps to reduce  
pollution and optimises washing performance in accordance  
with the water hardness level in your area. This information can  
be obtained from the organisation which supplies your  
household with water.  
- Switch on the appliance by pressing the ON/O77 button.  
- Press the P button and hold for approximately 10 seconds;  
two short beeps will sound, the text "WATER HARDNESS" will  
appear on the display and the set hardness number will also  
flash slowly on the display (the water softening system is set  
by default to number 3).  
Make sure the cap is screwed on tightly, so that no detergent  
can get into the container during the wash cycle (this could  
damage the water softener beyond repair).  
When necessary, measure out the salt before a wash  
cycle so that any saline solution which has leaked out of the  
salt dispenser is removed.  
* Only available in selected models.  
11  
 
Care and maintenance  
Clean the water inlet filter at the tap outlet regularly.  
Shutting off the water and electricity  
supplies  
EN  
- Turn off the water tap.  
- Unscrew the end of the water inlet hose, remove the  
filter and clean it carefully under running water.  
- Replace the filter and screw the water hose back into  
position.  
Turn off the water tap after every wash cycle to avoid  
leaks.  
Always unplug the appliance when cleaning it and  
when performing maintenance work.  
Cleaning the filters  
Cleaning the dishwasher  
The filter assembly consists of three filters which remove  
food residues from the washing water and then  
recirculate the water. They should be cleaned if you wish  
to achieve the best results in every wash.  
The external surfaces of the machine and the control  
panel may be cleaned using a non-abrasive cloth  
which has been dampened with water. Do not use  
solvents or abrasive products.  
Clean the filters regularly.  
Any marks on the inside of the appliance may be  
removed using a cloth dampened with water and a  
little vinegar.  
The dishwasher should not be used without filters, or  
if the filter is loose.  
• After several washes, check the filter assembly and if  
necessary clean it thoroughly under running water, using  
a non-metallic brush and following the instructions below:  
1. Turn the cylindrical filter C in an anti-clockwise  
direction and pull it out (fig. 1).  
Preventing unpleasant odours  
Always keep the door of the appliance ajar in order  
to avoid moisture from forming and being trapped  
inside the machine.  
Clean the seals around the door and detergent  
dispensers regularly using a damp sponge. This will  
avoid food becoming trapped in the seals, which is  
the main cause behind the formation of unpleasant  
odours.  
2. Remove the cup filter B by exerting a slight pressure on  
the side flaps (fig. 2).  
3. Slide out the stainless steel plate filter A (fig. 3).  
4. Inspect the trap and remove any food residue. NEVER  
REMOVE the wash cycle pump (black detail) (fig. 4).  
Cleaning the sprayer arms  
6ood residue may become encrusted onto the sprayer  
arms and block the holes used to spray the water. It is  
therefore recommended that the arms are checked from  
time to time and cleaned with a small non-metallic  
brush.  
B
C
The two sprayer arms may both be removed.  
1
2
To remove the upper sprayer  
arm, rotate the locking ring in an  
anti-clockwise direction.  
The upper sprayer arm should  
be replaced with the holes  
facing upwards.  
The lower sprayer arm can be  
removed by pressing on the  
side tabs and pulling it upwards.  
3
4
After cleaning the filters, replace the filter assembly and  
fix it in position correctly; this is essential for maintaining  
the efficient operation of the dishwasher.  
Leaving the machine unused for  
extended periods  
Cleaning the water inlet filter*  
Disconnect the appliance from the electricity supply  
If the water hoses are new or have not been used for an  
extended period of time, let the water run to make sure it  
is clear and free of impurities before performing the  
necessary connections. If this precaution is not taken,  
the water inlet could become blocked and damage the  
dishwasher.  
and shut off the water tap.  
Leave the door of the appliance ajar.  
• When you return, run a wash cycle when the  
dishwasher is empty.  
* Only available in selected models.  
12  
 
Precautions and advice  
The appliance was designed and manufactured in  
compliance with current international safety standards. The  
following information has been provided for safety reasons  
and should therefore be read carefully.  
Saving energy and respecting the  
environment  
EN  
Saving water and energy  
Only start a wash cycle when the dishwasher is full. While  
waiting for the dishwasher to be filled, prevent unpleasant  
odours with the Soak cycle (see Wash Cycles).  
Select a wash cycle that is suited to the type of crockery  
and to the soil level of the crockery using the Wash cycle  
table:  
General safety  
This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge,  
unless they have been given supervision or instruction  
concerning use of the appliance by a person responsible  
for their safety.  
- for dishes with a normal soil level, use the Eco wash  
cycle, which guarantees low energy and water  
consumption levels.  
Children should be supervised to ensure that they do not  
play with the appliance.  
- if the load is smaller than usual activate the Half load*  
option (see Start-up and use).  
The appliance was designed for domestic use inside the  
home and is not intended for commercial or industrial use.  
The appliance must be used by adults only, to wash  
domestic crockery according to the instructions in this  
manual.  
If your electricity supply contract gives details of electricity  
saving time bands, run wash cycles during the periods  
when a lower tariff is applied. The Delayed start*button  
(see Start-up and use) helps you organise the wash  
cycles accordingly.  
The appliance must not be installed outdoors, even in  
covered areas. It is extremely dangerous to leave the  
machine exposed to rain and storms.  
Do not touch the appliance when barefoot.  
When unplugging the appliance always pull the plug from  
the mains socket, do not pull on the cable.  
Phosphate-free and chlorine-free detergents  
containing enzymes  
We strongly recommend that you use detergents that do  
not contain phosphates or chlorine, as these products are  
harmful to the environment.  
The water supply tap must be shut off and the plug should  
be removed from the electrical socket before cleaning the  
appliance or carrying out any maintenance work.  
If the appliance breaks down, do not under any  
circumstances touch the internal parts in an attempt to  
carry out the repair work yourself.  
Enzymes provide a particularly effective action at  
temperatures around 50°C, and as a result detergents  
containing enzymes can be used in conjunction with low-  
temperature wash cycles in order to achieve the same  
results as a normal 65°C wash cycle.  
Never touch the heating element.  
Do not lean or sit on the open door of the appliance: this  
may cause the appliance to overturn.  
To avoid wasting detergent, use the product in  
appropriate quantities based on the manufacturer’s  
recommendations, the hardness of the water and the soil  
level and quantity of the crockery. Even if they are  
biodegradable, detergents contain substances that may  
alter the balance of nature.  
The door should not be left open as it may create a  
dangerous obstacle.  
The packaging material should not be used as a toy: it can  
become a choking or suffocation hazard.  
If your family includes children:  
• DO NOT allow children to play with the appliance or tamper  
with its controls.  
Recycling & Disposal Information  
• Keep detergents and rinse aids away from children.  
• Keep children away from the open door of a dishwasher,  
there could still be some detergent left inside.  
As part of Hotpoint's continued commitment to helping the  
environment, Hotpoint reserves the right to use quality  
recycled components to keep down customer costs and  
minimise material wastage.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical and  
Electronic Equipment (WEEE), requires that old household  
electrical appliances must not be disposed of in the normal  
unsorted municipal waste stream. Old appliances must be  
collected separately in order to optimise the recovery and  
recycling of the materials they contain and reduce the impact  
on human health and the environment. The crossed out  
"wheeled bin" symbol on the product reminds you of your  
obligation, that when you dispose of the appliance it must be  
separately collected.  
Please dispose of packaging and old appliances carefully.  
To minimise risk of injury to children, remove the door, plug  
and cut mains cable off flush with the appliance. Dispose of  
these parts separately to ensure that the appliance can no  
longer be plugged into a mains socket and the door cannot be  
locked shut.  
Consumers should contact their local authority or retailer for  
information concerning the correct disposal of their old  
appliance.  
* Only available in selected models.  
13  
 
Troubleshooting  
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance (see Assistance).  
EN  
Problem:  
Possible causes / Solutions:  
The dishwasher does not start or  
cannot be controlled  
Switch off the appliance by pressing the ON/OFF button, switch it back on after  
approximately one minute and reset the program.  
The appliance has not been plugged in properly.  
The dishwasher door has not been shut properly.  
The door wont close  
The lock was released. Strongly push the door until a clackingnoise is heard.  
No water drains out from the  
dishwasher.  
The dishwasher cycle has not yet finished.  
The water inlet hose is bent (see Installation).  
The drain duct is blocked.  
The filter is clogged up with food residues.  
The dishwasher makes excessive  
noise.  
The dishes are rattling against each other or against the sprayer arms.  
An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up  
and use).  
The dishes and glasses are  
covered in a white film or  
limescale deposits.  
The level of the refined salt is low or the dosage setting is not suited to the  
hardness of the water (see Rinse aid and salt).  
The lid on the salt dispenser is not closed properly.  
The rinse aid has been used up or the dosage is too low.  
The dishes and glasses are  
The rinse aid dosage is too high.  
streaked or have a bluish tinge.  
The crockery has not been dried  
properly.  
A wash cycle without a drying program has been selected.  
The rinse aid has been used up or the dosage is too low (see Rinse aid and  
salt).  
The rinse aid dispenser setting is not suitable.  
The crockery is made from non-stick material or plastic.  
The dishes are not clean.  
The racks are overloaded (see Loading the racks).  
The crockery has not been arranged well.  
The sprayer arms cannot move freely.  
The wash cycle is too gentle (see Wash cycles).  
An excessive amount of foam has been produced: the detergent has not been  
measured out correctly or it is not suitable for use in dishwashers (see Start-up  
and use).  
The lid on the rinse aid compartment has not been shut correctly.  
The filter is dirty or blocked (see Care and maintenance).  
The refined salt level is low (see Rinse aid and salt).  
The dishwasher does not take any There is no water in the mains supply.  
water in - Tap shut-off alarm  
(the ON/OFF indicator light flashes and  
the following message appears on the  
display: No water. Open tap. After a  
few seconds, A:6 will appear).  
The water inlet hose is bent (see Installation).  
Turn on the tap and the appliance will start after a few minutes.  
The appliance lock has been activated because no action was taken when the  
beeps sounded.  
Switch off the appliance using the ON/OFF button, turn on the tap and switch  
the appliance back on after 20 seconds by pressing the same button. Re-  
program the appliance and restart the wash cycle.  
Water inlet hose alarm / Water inlet Switch off the appliance by pressing the ON/OFF button. Shut off the water tap  
filter blocked  
(the ON/OFF indicator light flashes and  
the display shows A:7).  
to eliminate the risk of flooding and remove the plug from the electrical socket.  
Make sure the water inlet filter has not become blocked by impurities (see Care  
and maintenancechapter).  
* Only available in selected models.  
14  
 
After Sales Service  
Appliance Registration  
After Sales Service  
EN  
We want to give you additional benefits of Hotpoint  
ownership. To activate your free 5 year parts  
guarantee you must register your appliance with us.  
No one is better placed to care for your Hotpoint  
appliance during the course of its working life  
than us - the manufacturer.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in the country  
offering you access to 400 skilled telephone  
advisors and 1000 fully qualified engineers on call to  
ensure you receive fast, reliable, local service.  
Indesit Company UK Ltd. Morley Way,  
Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial  
Estate,Dublin 17  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Recycling and Disposal Information  
Please note: Our advisors will require the  
following information:  
As part of Hotpoint's continued commitment to  
helping the environment, Hotpoint reserves the right  
to use quality recycled components to keep down  
customer costs and minimise material wastage.  
Model number:  
Please dispose of packaging and old appliances  
carefully.  
To minimise risk of injury to children, remove the  
door, plug and cut mains cable off flush with the  
appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged  
into a mains socket and the door cannot be locked  
shut.  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement  
parts as well as accessory products that protect  
and hygienically clean your appliance to keep it  
looking good and functioning efficiently throughout  
its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
15  
 
Guarantee  
195095212.02  
09/2011 - Xerox 6abriano  
Guarantee  
EN  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because  
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to  
you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,  
batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY Iꢀ THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will be a  
charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (Republic of Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense of  
repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226  
(Republic of Ireland 01 230 0233).  
9ree Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to  
arrange for an engineer to call.  
16  
 

Graco Crib PD147439C User Manual
Graco Stroller PD240819A User Manual
Grizzly Nail Gun H2912 H2913 User Manual
Haier TV Receiver 29FA10 AM User Manual
Harbor Freight Tools Sander 42864 User Manual
Hasbro Games Guess Who User Manual
Hasbro Games X Men User Manual
Hoshizaki Ice Maker B 1150SS User Manual
HP Hewlett Packard Calculator 48gII User Manual
HTC PDAs Smartphones PHAR100 User Manual