Haier Washer XQB50 68 User Manual

Full automatic washing machine  
User's manual  
This manual is for  
XQB50-68  
Special number 0030506438  
Please read this manual  
carefully before using.  
 
Retain it for future reference.  
Names of the parts  
Top lid  
Water level knob  
Detergent box  
Power switch  
Water inlet valve  
Power wire  
Lint filter(Installed by user)  
Cabinet handle  
Control panel seat  
Water  
channel  
Filter cover  
Inner tub  
Drain hose  
Front control board  
Control panel sheet  
Drain hose  
hanging hole  
Pulsator  
Cabinet  
Front fixed foot  
Drain outlet  
protecting cover  
Drain hose bushing  
Back cover  
Rear fixed foot  
Adjustable foot  
Adjustable foot seam  
Meaning and description of the symbols  
Contents marked with that symbol are related  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damageof the machine or injure the  
personal safety of the user.  
Warning sign  
Contents marked with that symbol are actions  
forbidden to perform. Performing of those  
actions may result in damage of the machine  
or injure the personal safety of the user.  
Forbidding sign  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
 
Safety precautions  
Please insert the power cord into  
special receptacle with rated vol-  
tage.Be sure to use single-phase  
three pins receptacle.The earthing  
terminal of the receptacle must be  
earthed reliably.If possible,please  
adopt electric leakage protector.  
When the machine is normally  
using, please put the power plug  
at the location easily to be insert-  
ed and extracted by hand. Be sure  
to pull the plug off when there's  
power failure, or the machine is  
being moved, cleaned orwhen it  
is idle.  
Earth  
If the power cord is bad, to avoid risk it is required to replace it by the  
technicians ofour special shop or the after-sale service department.  
Keep the pin of the power plug clean.  
Do not put the machine at damp  
Do not use water hotter than 50 C .  
place like the bathroom . Never  
wash it with water. Do not place  
wet laundries on the control panel.  
In case the washing machine is in-  
stalled on ground with carpet, do not  
block the ventilation hole with carpet.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
The ventilation holes  
at the bottom  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
 
Safety precautions  
Do not stretch hands into the working  
Do not decompose, repair or alter the  
machine by yourself.  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not put any hot or heavy items (such  
as the kettle with hot water ) on the  
washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.)  
l
tro  
r
e
Pe  
inn  
h
T
Keep the machine away from direct  
sunlight and heat source like the heater.  
The handicapped or children without  
care shall not use the machine.  
To prevent the lint inside the tub from  
blockingthe cascade outlet during  
washing, please keep the lint filter in  
good condition, and install it to proper  
position. If the lint filter is lost or da-  
maged, please contact the local after-  
sales service department of our company.  
To protect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
Please check if the water faucet is open,  
and if the connection of the water inlet  
pipe is proper.  
It is suggested to use foamless washing  
powder.  
Install  
Dismantle  
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual. It is  
very important to your security and correct operating the machine.  
Install the bottom plate  
After you open the package, please lean  
the washing machine gently down on soft  
Back  
items ( like the towel cloth, blanket, etc. ).  
Install the bottom plate to the bottom of  
the machine with the eight screws by  
a cross screwdriver, then lift the machine  
up gently. See to the figure:  
Front  
Bottom plate  
Soft items  
Screw  
Adjust the installation position  
The largest allowed slope of the base of the machine is 2 . The slanting or rough  
ground will result in unstable running or stoppage of the machine. Please adjust  
it with following methods:  
Confirm it's horizontal:  
Hang the lead line to confirm if it is horizontal.  
Adjust the adjustable foot:  
1.To twist the adjustable foot, please first lift up the side of the foot slightly, loosen  
the adjustable nut, and twist the foot.  
2.Fasten the nut after adjustment.  
Adjustable nut  
Fasten  
Loosen  
High  
Adjustable foot  
Low  
Install the lint filter  
After opening the package, please take out the lint  
filter from the document bag, install it to the  
inner tub. See to the figure.  
Install  
 
How to change the direction of the drain hose  
1.Dismantle the back cover of the washing  
machine.  
3.Dismantle the protecting cover of the  
drain outletat the other side (method  
the same as the bushing). Install the  
bushing as per indicated in Figure 4.  
2.Put down the drain hose. Take off the  
drainhose frame. As indicated in Figure  
1, put thedrain hose into the cabinet.  
Then stretch onehand into the cabinet  
to nip the claw of the drain hose bush-  
ing to remove the claw fromoriginal  
position. Take off the drain hose bush-  
ing with the other hand. (As indicated in  
Figure 2 and 3).  
4.Extend the drain hose from the other  
side. Fix thedrain hose onto the base  
frame with the drain hoseframe. (As  
indicated in Figure 5)  
Drain outlet  
protecting cover  
Outer  
drain  
hose  
Drain hose bushing  
Drain hose bushing  
Drain hose frame  
Figure 1  
Figure 2  
Figure 4  
Figure 5  
Cabinet  
5.Install the protecting cover of the drain  
outlet at the other side as per indicated  
in Figure 6.  
Inner Outer  
Press  
Drain hose  
bushing  
Take off  
Drain hose  
bushing claw  
Press  
Figure 3  
Figure 6  
Usage of the drain hose  
Before using , hang up the drain hose on suitable location.  
Do not put down the drain hose on the ground.  
Confirm the end of drain hose is higher than  
the level of tub . If not the siphon will being .  
<1.2m  
 
Install the water inlet hose  
Confirm the water faucet  
Water faucet, not suitable  
Water faucet, suitable  
It is required that the front end shall be longer than 10cm.  
The outlet end surface of the faucet shall be flat and smooth. If not please file it to  
avoid leakage.  
Connection between the water inlet hose jointer and the water faucet  
1.Press the lower end of the lock lever and push down the slider. Take off the  
water inlet hose jointer from the water inlet hose component. See to Figure 1.  
2.Loosen the screw till the water faucet can be accessed. Put the jointer of the  
water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and  
the jointer can not be set on the water faucet, please loosen the four screws  
and take out the bushing in the jointer. The front end of the faucet must be  
smooth, otherwise it may leak water. See to Figure 3.)  
Water inlet hose jointer  
Screw  
Slider  
Lock lever  
Nameplate  
Screwdriver  
Bushing  
Water inlet hose  
Figure 1  
Figure 2  
Figure 3  
3.Fasten the four screws evenly. See to Figure 4.  
4.Take off the nameplate. Twist the fastening nut as per the indication of the  
figure to seal up the outlet end surface of the faucet. See to Figure 5.  
Remarks:  
Before installation, the threading is 4mm above the upper surface of the  
nut. After installation, the threading is 2mm above the upper surface of the nut.  
About 4mm  
See to Figure 6.  
before twisting;  
about below 2mm  
after twisting  
Nut  
Figure 6  
Figure 4  
Figure 5)  
 
Connection between the water inlet hose and the washing machine  
1.Do not take off the water absorption cushion.  
Nut of the water I  
nlet hose  
Please check if the cushion is dropped or  
damaged before each usage. If it happens  
please contact our after-sale department  
immediately.  
2.Put the nut of the water inlet hose on the  
valve jointer.  
3.Fasten the nut. Swing it gently to confirm  
if it's suitable.  
Water absorption cushion  
Jointer of the  
water inlet valve  
Connection between the jointer of the water inlet hose and the water inlet hose  
1.Push down the slider. Insert the water inlet  
Jointer of the  
hose into the jointer.  
2.Hang the lock lever to the jointer. Release  
the slider till a click sound is heard.  
water inlet hose  
Locking lever  
Slider  
Check the connection between the jointer of the water inlet hose and the water faucet  
1.Swing the hose gently to confirm if it is fastened  
stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Each time before use please check if the  
connection between the jointer of the water inlet  
hose and the water faucet, and the installation  
of the water inlet hose are firm, so as to prevent  
dropping from improper installation position.  
Dismantle the water inlet hose  
1.Close the water faucet.  
2.Press the locking lever. Push down the slider.  
Then pull off the water inlet hose. If the machine  
is used more than once every week, the jointer  
of the water inlet hose can be kept on the faucet  
to prevent damaging the fixing screw.  
Locking lever  
Slider  
 
1Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose. Open  
the water faucet.  
2.Confirm that the washing machine is  
earthed reliably. Then insert the  
power plug into the receptacle. The  
earth terminal shall not link to gas  
pipeline and faucet water pipeline.  
3.Hang up the drain hose.  
<1.2m  
Pay attention to followings before washing the laundries  
Check if  
The quantity of  
When the pulsator  
Clear the  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
the laundries is running , the  
shall not be too buttons of the  
large. Stretch laundries may  
and loosen the cause noise. For  
laundries before the sake of  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
 
2 Put in the laundries  
The capacity of washing and spinning of  
the machine refer to the largest weight of  
the standard laundries under dry condition  
that can be washed or spinned in one time.  
One time washing quantity shall be lower  
than the rated capacity.  
The thickness, size, type of the cloth will  
influence the actual washing capacity. It is  
suitable for one time washing to put in  
reasonable amount of laundries and the  
laundries can be turned round in washing.  
Do not select "High"water level for laundries  
small than 1.0kg, so as to avoid splashing  
of water.  
3 Add the detergent  
How to use the washing powder  
Direct dissolved in the machine  
1.Fill water to "Low" water level.  
2.Add the power. Run for 30 seconds to  
dissolve it completely.  
3.Put in the laundries. Select suitable  
water level.  
The instant dissolving of the washing  
powder:  
How to use the whitener  
1. Prepare warm water of 30  
container.  
2. Add the powder while stirring to fully  
dissolve it.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
It is suggested not to use high sudsing  
detergent.  
Different washing powders have different  
dosage. Please refer to the usage manual  
of the washing powder for the details.  
and a  
Fill water to decided level. Dilute  
the whitener with container. Pour  
it slowly into the washing tub.  
Avoid using whitener on laundries  
with color or pattern as they are  
prone to lose color.  
The whitener shall not touch the  
laundries directly.  
Refer to the user's manual for the  
usage and quantity of the whitener.  
For powder whitener, please dissolve  
it before use.  
 
4 Use the operation knobsand buttons  
a Description of the function of the knobs and buttons  
Mode and meaning of the indicators  
Flashing: indicate the running program  
On: indicate the program about to run, or indicate the selected mode  
Flashing rapidly: indicate abnormal condition  
Start  
Process  
Selection  
Pause  
Spin  
Quick-  
wash  
Twice-  
wash  
Rinse  
Wash  
"Process selectionbutton  
One or more out of the five process programs  
are available for your option: quick- wash, twice-  
wash,wash, rinse, spin  
"Start/Pause" button  
After the power is switched on, push it  
to start the machine  
During working, push it to pause  
working.  
During pause, push it to resume  
working.  
 
b .Steps of using the operation buttons and description of the steps  
"Power" botton  
Push the "Power" button to  
switch on or off the power.  
When the power is on, push it  
again to switch off the power.  
Start  
Process  
Pause  
Selection  
Quick-  
wash  
Spin  
Rinse  
Twice-  
wash  
Wash  
Power  
Auto off  
Water Level  
Low  
Medium  
High  
Reset  
On  
Off  
Power  
Low  
Auto off  
Medium  
High  
Reset  
On  
Off  
"Water Level " button  
Select or adjust the water level.  
1 Push the "Power “ button to switch on the power  
ON  
OFF  
Process  
Selection  
2 Push the "Process Selection" button to select  
the suitable process  
After switching on the power, the machine will set to standard program automatically  
including " wash-rinse-spin ". To select other program, push the "Process Selection"  
button to select one or more programs among "Quick- wash" "Twice- wash" "Wash"  
"Rinse" "Spin". Refer to the "Selection method of the procedure programs " for the  
selection.  
Page 12  
 
Attention  
Even there's no water in the tub, the  
spinning will start after a certain period.  
Do not use the "Twice wash" program  
for the woolen laundries.  
Wash the laundries that are prone to  
lose colors separately from other laundries.  
The pulsator will not rotate unless the water is filled to selected water level.  
Selection method of the procedure programs  
Times of pushing  
the "Process  
Selection" button  
Contents (the lighted indicators  
indicate the programs about to run)  
Selected procedure  
program  
Applicable procedure  
Quick- Twice-  
Wash rinse spin  
wash wash  
When the common laundries  
need washing , rinsing and  
spinning  
Wash, rinse, spin  
(standard program)  
Wash (the washing  
liquid remains in  
the tub)  
Quick- Twice-  
Wash rinse spin  
wash wash  
Repeat using the washing  
liquid  
Quick- Twice-  
Wash rinse spin  
wash wash  
Wash, rinse ( the  
rinsing liquid remains  
in the tub)  
Repeat using the washing  
liquid  
Quick- Twice-  
Wash rinse spin  
wash wash  
When the laundries need  
rinsing and spinning after  
manual washing  
Rinse, spin  
When the laundries need  
only spinning after manual  
washing (first drain then spin)  
Quick- Twice-  
Wash rinse spin  
wash wash  
Spin  
(spin after drain)  
Quick- Twice-  
Wash rinse spin  
wash wash  
If the laundries are very dirty,  
or the sleeve and collar are  
dirty, first soak then wash  
Twice-wash, wash,  
rinse, spin  
Quick- Twice-  
Wash rinse spin  
wash wash  
Quick-wash, wash,  
rinse, spin  
When quickly wash the  
light dirty laundries.  
If you push the "Process Selection" button for 7 times, it will resume the original mode, and  
it will circulate like that.  
If you select the "Quick wash" program, you have to set the full procedure of wash, rinse  
and spin. The procedure cannot be selected.  
 
* Total time: including the normal water inlet time, drain time, excluding the power off  
time. The total washing time may be influenced by the water inlet pressure and  
water level.  
* Spin time: the time from intermittent running to finishing  
* When selecting " Twice-wash " program, first soak for about 20 minutes, pre-wash  
for about 8 minutes, then soak for about 5 minutes, then do washing, rinsing and  
spinning. The wash time in the list includes the pre-wash time.  
3.Adjust the "water level “ knob to select suitable water level  
Three water levels available according to the laundries quantity: High; Medium; Low.  
Page 11  
After the water inlet as per the preset water level, in case additional water  
quantity is required, please first set the button to the "Reset", push and hold it  
to perform automatic water inlet. When it reaches the suitable water level, you  
can turn it to the needed water level.  
After the water inlet under set water level, if higher water level is needed, please  
first turn the knob to " Reset ", then turn back to needed water level. The wash-  
ing machine will fill water to the new water level.  
4 Press the "Start/Pause" button  
Start  
Pause  
6 The washing is finished  
5 Close the top lid  
When the washing is finished, the  
three indicators of "Wash" "Rinse"  
"Spin" are all on.The power will be  
switched off automatically about 10  
minutes after the finishing of the  
washing.  
If you open the top lid, the machine  
will stop working before spinning  
 
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
The lint filter must be used during  
washing.  
It must be cleaned in time after each  
using  
Lint filter:  
Clean the detergent box and set it on  
the control panel seat.  
1.Pull it up to dismantle.  
2.Push it down to install.  
3.Clean the filter screen after washing.  
Install  
Dismantle  
Clean  
If the cabinet is dirty, wipe it with wet cloth  
The filter screen of the water inlet valve is  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
Do not wipe it with thinner, petrol,  
alcohol etc.  
likely to be blocked by foreign materials  
and influence the water inlet. Please clean  
it with brush every two months.  
l
er  
Petro  
Thinn  
Alcohol  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely  
after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid  
for some time (about 1 hour), then close the top lid.  
 
Trouble-shooting Answers to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending it  
to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Phenomenan  
The reason  
How to settle  
In spinning, the machine stops  
running. (The "wash" "rinse"  
"spin" indicator flash quickly)  
Close the top lid.  
The top lid is not closed.  
The draining does not work,  
or the speed of draining is  
too slow ( the indicators of  
"rinse" "spin" flash)  
Is the drain hose blocked  
by foreign material?  
Clean the foreign material.  
Open and close the top lid once.  
The safety switch acts. The  
spinning can not work (the  
indicators of "wash" "rinse"  
flash quickly)  
Are the laundries put  
slantingly?  
Is the machine slanting?  
Re-order the laundries.  
Close the top lid.  
Level the machine in right position.  
Open and close the top lid once.  
Open the water faucet. Push  
the "Start/Pause" button.  
Clean the water inlet valve.  
Push the "Start/Pause" button.  
The water faucet is not open.  
The program pauses after  
about 15 minutes of water  
inlet (the indicators of "wash"  
"spin" flash quickly)  
The water inlet valve is  
blocked  
Wait for the normal water  
pressure before use.  
The water pressure is too low  
and the current is too small.  
Is there power failure?  
Is the power plug loose?  
If water level reach the appoint level?  
Use it when the power is on.  
Insert the power plug tightly.  
No wash  
Affusion to appoint level.  
The machine does  
not act.  
Insert the power plug tightly.  
Close the top lid  
Is the power plug loose?  
Is the top lid is not closed.?  
No spin  
Re-order the laundries.  
Close the top lid.  
Are the laundries put  
slantingly?  
There's abnormal sound  
inside the machine.  
Is the machine slanting?  
Are the laundries slanting  
in spinning?  
Level the machine properly.  
Re-order the laundries.  
Is the jointer screw of the  
water inlet hose is loose  
or twisted awry?  
The water faucet leaks.  
Fasten the jointer screw  
properly.  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The program is setting the drain time. Some  
time is needed before it starts spinning.  
Push the "Process selector" button to  
select "Spin", but it doesn't work.  
There may be some water flowing out of  
the drain hose in the first use of the machine.  
It is the water remained in the factory  
inspection of performance.  
It is because that the laundries are slanting  
to one side, and the safety switch acts. After  
water inlet and stirring, the slanting will be  
removed and the spinning will work.  
In the final spinning, it stops and displays  
"Rinse", and starts water inlet.  
 
Paching list  
Name  
Quantity  
User's manual  
One piece  
One piece  
Certificate of warranty  
Components of the  
water inlet hose  
The end connecting to  
the washing machine  
Jointer connecting the  
water inlet hose and  
the water faucet  
One piece  
The end connecting  
to the water inlet hose  
jointer  
Bottom plate  
One piece  
Tapping screws  
Lint filter  
Egiht pieces  
One piece  
One set  
Full automatic  
washing machine  
Specification  
Water level/Water quantity (about)  
High/52L, Medium/43L, Low/30L  
5.0 (weight of standard dry cloth)  
Injection pressure(MPa  
Rated washing / spinning capacity(kg)  
 

Grizzly Dust Collector Model G0562 User Manual
Grizzly Lathe g0746 User Manual
Gyration Mouse TM ULTRA CORDLESS OPTICAL MOUSE User Manual
HANNspree Flat Panel Television K215 10A1 User Manual
Hans Grohe Plumbing Product 32310001 User Manual
Honeywell Cell Phone 70 82 25 18 User Manual
HP Hewlett Packard Speaker 4275A User Manual
HP Hewlett Packard TV Mount 699728 001 User Manual
HP Hewlett Packard Welder 519819 001 User Manual
Hypertec Carrying Case 6101HY User Manual