Haier Washer Dryer HWM70 0588 User Manual

Environmental-friendly Double  
Drive Washing Machine  
User's manual  
This manual is for  
HWM70-0588  
Please read this manual  
carefully before using.  
Retain it for future reference.  
 
Names of the parts  
Packing list  
Water inlet valve  
Water absorption gasket  
One  
One  
User's manual  
Warranty card  
Inside the document bag  
Inside the document bag  
Top lid component  
Inner cover  
Detergent box  
Control panel seat  
Outer tub cover  
Balance ring  
Power cord  
Screw cover  
Hook  
Components of the water inlet  
hose  
Cabinet handle  
Drain hose  
Attach block  
One  
Inside the accessory bag  
Inner tub  
Lint filter  
Pulsator  
Front control board  
Cabinet  
Front door  
Drain  
protective lid  
Bottom plate  
Between the upper cushion of the washing  
machine package and the upper seal of the  
package carton  
One  
Liquid blenching filler  
Adjustable leg  
Back cover  
Drain protective lid  
Base frame  
Fixed leg (3 pieces)  
Inner cover  
component  
One  
Inside the accessory bag  
Meaning and description of the symbols  
Automatic washing machine  
One  
Warning sign  
Contents marked with that symbol are related to the  
safety of the product and the personal safety of the users.  
Please operate in strict conformity to the contents.  
Specification table  
Water level/Water  
quantity (about)  
Forbidden sign  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those action may result in damage of  
the machine or influence the personal safety of the users.  
Water Injection pressure  
0.03MPa  
0.78MPa  
~
Standard washing /  
spinning capacity  
7.0kg/7.0kg  
1
 
Trouble-shooting answer to question  
Safety precautions  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.  
Please confirm again before sending it to repair. Do not repair it by yourself.  
The washing machine must be positioned  
Please plug the power plug on special  
receptacle. Be sure to use three-pins  
power receptacle. Ensure that the earthing  
prong of the power receptacle is earthed  
reliably. Use leakage protector if possible.  
Phenomena  
The reason  
How to settle  
so that the plug is accessible. Be sure to pull the  
plug off and close the water faucet in  
following cases: power failure, delivering  
the machine, setting the machine idle or  
c l e a n i n g t h e m a c h i n e . D o n o t p l u g  
or pull the power plug with wet hand.  
Close the top lid.  
The digitron displays E0.  
The top lid is opened during reserve procedure.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
Put down the drain hose. Open and close the top lid once.  
Clean the foreign material. Open and close The top Lid Once.  
It stops running in midway. The digitron  
displays E2.  
The top lid is not closed.  
Close the top lid.  
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.  
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with  
dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by  
the technicians of our special shop or our customer care agent.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Are the laundries put slantingly?  
Is the machine slanting?  
Reorder the laundries. Close the top lid.  
Th machine will start running after 10  
seconds of being placed horizontally.  
Open the water tap. Push the start/Pause  
button once.  
Clean the water inlet valve then push  
the Start/Pause button once.  
Push the Start/Pause button once.  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
The water filling does not work, or is  
slow. After about 15 minutes later,  
the digital displays E4.  
Please contact the after-sales  
service department.  
The digitron displays E6.  
The digitron displays E7.  
The water level sensor is bad.  
The communication is bad.  
In case the washing machine is installed on ground with  
carpet, do not block the ventilation hole with carpet.  
Do not use water hotter than 50  
.
Please contact the after-sales service  
department.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
The ventilation  
holes at the bottom  
Not wash  
The machine does  
not act  
Carpet  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Not spin  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
There's abnormal sound  
inside the machine  
Is the screw of the jointer of water  
inlet hose loose or awry?  
Fasten the screw of the jointer properly.  
The water tap leaks  
Do not put the machine at damp place like  
the bathroom. Never wash it with water. Do  
not put wet laundries on the control panel.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The wash procedure is paused.  
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.  
The program is setting the drain time. Some time is needed  
before it starts spinning.  
Push the PROGRAM button to select SPIN,  
but it doesn't work.  
The pulsator pauses during water inlet  
in wash and rinse.  
Do not let the machine share one receptacle with other  
electric appliances. If the plugging into the receptacle  
is loose, do not use the plug any more.  
It is to avoid splashing during water inlet.  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained in the factory inspection of performance.  
2
 
Disposal after washing  
Safety precautions  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Do not put hand into the rotating tub. It is dangerous  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
Do not decompose, repair or alter the machine by  
yourself.  
Please first pull off the power plug from the receptacle before cleaning.  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
Lint filter:  
1.Push down the spring piece of the top lint filter  
to make the claws out of the filter cover, and then  
pull out the lint filter to get it down. figure1  
2.Pull the back of the lint filter, and then you can  
get down it off the front cover of the lint filter. figure2  
3.Sweep the rubbish in the lint filter.  
Clean the detergent box and set it on  
the control panel seat.  
1.The method of dismantle: Push it up aslant and gently.  
2.The method of install : install it upwards and aslant  
and push it in .  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
Do not wash laundries with volatile materials  
(such as thinner, petrol etc.).  
4.Put the back of the lint filter into the front cover .  
5.Put the lint filter into filter cover, and make it  
tight .  
trol  
Pe  
Benzene  
6.Make sure the lint filter well installed, or it can  
influence your use.  
The back cover of lint filter  
Up  
Up  
Dismantle  
Dismantle  
Dismantle  
Install  
Install  
Install  
Down  
Keep the machine away from direct sunlight and  
heat source like the heater.  
The handicapped or children without care shall not use  
the machine.  
The front cover of lint filter  
Figure 2  
Down  
Figure 1  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Please clean it with brush every two months.  
Wipe it with neutral detergent.  
Do not wipe it with thinner, petrol, alcohol etc.  
r
e
Petrol  
Alcohol  
Thinn  
Please keep the lint filter in good condition,  
and install it to proper position during  
washing. If the lint filter is lost or  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand, hairpin  
and other foreign materials before washing.  
Install  
Dismantle  
damaged, please contact the customer  
care agent of our company.  
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
To change the direction of drain pipe, please contact the customer care agent of our company.  
4.Hang up the power cord and drain hose.  
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,  
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use  
otherwise the washing effects may be lowered or the washer may be damaged.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
3 Push "SOAK" "WASH/SPEED" "RINSE" "SPIN/SPEED"  
button to select suitable procedure program  
Install the Inner cover component  
Attention  
Before initial use of the machine, assemble the inner cover as described below:  
1.Open the top lid of the washing machine.  
2.Put the inner cover component on the outer tub cover, aiming  
the inner cover shaft to the installation hole of the  
corresponding outer tub cover shaft groove.  
Even there's no water in the tub, a certain period is required before spin starting.  
Separate the laundries that are not colorfast from other laundries in washing.  
The soak procedure can work in cooperation with automatic programs like normal, comforter  
There is intermittent pulsator stirring during soak.  
After the machine starts operation, you can only set the program and procedure during washing,  
and can not make setting in other cases.  
Outer tub cover  
Outer tub cover shaft groove  
Inner cover shaft  
Inner cover  
3.Firstly insert the inner cover shaft of one side into the  
corresponding outer tub cover shaft groove, then push  
the another inner cover shaft into the corresponding  
outer tub cover shaft groove. Please install to designated  
position to guarantee there are no dropping or abnormal  
sound in opening and closing of the inner cover, and the  
operation shall be smooth. Do not dismount the inner cover  
component after washing.  
If the water pressureis too low,in order to washthe cloth cleanly,the machine will change  
from " SAVING WATER"to "storing water "automatically.  
Damping cushion  
4 Push the " WATER LEVEL "button, select  
suitable water level  
Push  
Section I enlarging  
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.  
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"  
button, then push the "WATER LEVEL" button to set the water level.  
Install the bottom plate  
5 Push the "AIR DRY"button to select suitable dry time.  
After you open the package, please lean  
the washing machine gently down on soft  
items ( like the towel cloth, blanket, etc. ).  
Install the bottom plate to the bottom of  
the machine, then lift the machine up  
gently. See to the figure:  
I
Back  
6 Push the "RESERVE" button to select suitable reserve wash  
program  
After switching on the power, the reserve program is set to off mode automatically. If you need to  
set the washing procedure to be finished at reserved time, please push the " RESERVE " button to  
set the reserve wash program. Refer to reserve button in Page 11 for selection.  
Front  
Bottom plate  
Soft items  
Two claws at the bottom cover shall  
be inserted in two bar-shaped holes  
in the stand. Make sure the claws  
are firmly in place.  
Section I enlarging  
Confirm the operation of reserve program  
When the "RESERVE" function is activated, the indicator light of the program you  
have set will be off. The "reserve (hour)" and "time remain" indicator lights will  
be on. During reserve procedure, push the "RESERVE" button to display the reserve mode.  
To change the running program or cancel the reserve setting, you  
Adjust the Installation position  
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground  
will result in unstable running or stoppage of the machine. Please adjust it with following methods:  
need to switch off the power and make new selection.  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
7 Push the "START/PAUSE" button  
6 Finish washing  
Adjust the adjustable leg:  
5 Close the top lid  
1 .To twist the adjustable leg, please first lift up the  
side of the leg slightly, loosen the adjustable nut,  
and twist the leg.  
After finishing wash it'll  
alarm and switch off power  
automatically  
As the top lid opened, the washer will automatically  
given alarm and stop running, exclusively during  
draining.  
the adjustable nut  
Fasten  
Loosen  
2 . After adjustment, fasten the nut.  
the adjustable feet  
High  
Low  
 
How to change the direction of the drain hose  
1.Dismantle the rear cover of the washing machine.  
3.Dismantle the drain outlet protecting cover at the other side,  
(the way is the same as the drain bushing),then install the drain  
bushing, as indicated in Figure 4.  
2.Put down the drain hose Take off the drain hose  
frame as indicated in Figure 1.Take the drain hose into  
the cabinet then nip the drain fixing clamp to make  
it deviated from the clip the other hand is used to put  
down the drain bushing as indicated in Figure 2 3.  
b
Steps of using the operation buttons and description  
Wash/spin  
speed  
Program  
REMAIN  
of the steps  
SOAK  
WASH  
RINSE  
SPIN  
••  
4.Extend the drain hose from the other side. Fix the drain hose  
with drain hose frame onto the cabinet, as indicated in Figure 5.  
Normal  
Air dry  
120  
Standard  
4
Woollen  
Carpet  
3
Quick wash  
Posthaste  
60  
2
drain outlet protecting  
cover  
Saving water  
Jean  
Overflow  
RESERVE  
Drain hose  
SPIN  
PROGRAM  
RESERVE  
Figure 5  
Figure 4  
SPEED  
LOCK  
Drain hose support  
Cabinet  
Inner  
Drain bushing  
Figure 2  
Drain bushing  
7
Figure 1  
5.Install the drain outlet protecting cover to the other side,  
as indicated in Figure 6  
Outer  
4
2
Push  
Drain bushing  
Take  
down  
Drain hose fixing  
clamp  
Figure 6  
Push  
Figure 3  
1.Push "POWER" button to switch on the power  
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose  
with our company serviceman .  
2.Push "PROGRAM"button to select suitable full-auto program  
After the power is switched on, "Normal" is automatically set. To select other full-auto program, please push  
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 11.  
E.g. Set to "Speedily"program for small quantity of laundries with light soil.  
Usage the drain hose  
The drainage shall be smooth with the drain hose.  
1.The height of the drain hose shall be less than  
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be  
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.  
Notes:  
4.If extra drain hose is needed, please make  
10cm, or the drainage will not be smooth, and  
separate purchase. The inner diameter of the  
cost such long time that the machine may stop  
extra hose shall not less than 30mm, and the  
The washing machine has a Woollen program and a Carpet program, intended for high-grade fabrics such  
as cashmere and carpet. First, make sure the laundry can be washed with water or not. If not, do not use the  
washing machine to wash the laundry. If yes, select the washing cycle recommended by the fabric man  
ufacturer. The Woollen program can be used to wash fine clothes such as cashmere sweater, linen blouse,  
woolen pants; the Carpet program can be used to wash carpets or heavy fabrics indicated as hand wash or  
machine wash compatible. For clothes with local stains, such as sticky stains at collar or cuff, lay the clothes  
upon a towel and spread neutral detergent (for washing machine) on the stains. Use a soft brush to pat at the  
clothes gently before putting the clothes into the machine. Do not rub the clothes hard.  
Before washing, please fold up the laundry as needed, then put the laundry into the inner tub, flat and neat.  
These fabrics are not washable:  
at mid way.  
length shall not exceed 1.5m.  
2.Do not step on or press the drain hose.  
>
30mm  
<10cm  
<1.5m  
1. Fabrics that deform when soaked in water;  
2.Fabrics that shrink, discolor or go through other exterior changes when soaked in water;  
3. If the drain hose is too long, cut it at mid point.  
To make smooth drainage, cut the front end of  
the hose slantingly.  
5.If the extra hose is too long, cut it either at A  
or at B.  
3.Fabrics that lose original texture when soaked in water;  
4.Fabrics that discolor when soaked in water;  
5.Fabrics that have pilling or pressed pile when soaked in water;  
6.Fabrics that have damage when soaked in water.  
Upon completion of washing, iron the laundry with a steam iron.  
When shrinkage occurs  
Hold the steam iron above  
Stretch the laundryto its original  
the laundry and do not touch  
size and locate it with pins. Use  
the laundry. Reshape the  
a steam iron to dry the laundry  
completely. Donot touch the  
laundry. (Asillustrated in Fig 2)  
laundry. (As illustrated  
in Fig 1)  
Pin  
Figure 2  
Figure 1  
5
12  
 
Install the water inlet hose  
Confirm the water faucet  
Water faucet,suitable  
"Air dry"button  
.
Push the button to toselect the different air dry time(60 120 180  
Reserve, remain time digitron  
).  
Minutes .To select60minutes can dry theinner or outer tub.  
It displays "--" during detecting.  
Water faucet,not suitable  
To select120 or 180minutes candry clothes.(both lighter ison  
indicate the 180minutes program).The weight of the clothes is  
1.5kg at most.  
It displays remained reserve time (hour).  
It displays total remained time (min). If the total time  
exceeds 99 minutes, it uses "A" on tens digit to  
represent100 minutes, and uses "b" to represent 110  
minutes. E.g. "A3" represents 103 minutes.  
It displays abnormal symbol in abnormal situation.  
(See to Page15)  
Outlet end surface  
>10mm  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
"POWER" button  
Push the "POWER" button to switch on the power.  
Under power-on mode, push it to switch off the power.  
Push the "POWER" button to switch on the power. If  
the "START/PAUSE" button is not pushed, the machine  
will switch off the power automatically after 5 minutes.  
Remain  
Program  
Standard  
••  
Normal  
Quick  
Connection between the water inlet hose jointer and the water faucet  
Woollen  
Carpet  
Saving water  
Air dry  
120  
Posthaste  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
60  
Jean  
Reserve  
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
dry  
Air  
Program  
Reserve  
LOCK  
water inlet hose jointer  
Screw  
Slider  
Sign plate  
Screw knife  
Bushing  
Figure 3  
"PROGRAM"button  
Lock level  
"WATER LEVEL"button  
"RESERVE" button  
Following full-auto program is available  
The washing machine can detect the laundries automatically.  
After detection, it will set the water level to suitable value among  
4, 6, 8,and 10 automatically.  
You can also set water level by yourself. After the machine is  
started, it will not set water level automatically. You shall push the  
start/pause button to make new setting.  
If there's water inside the tub, the machine cannot detect the  
laundries and will display water level 6 .If wet laundries are put  
in, it may display water level 10. You must set suitable water level  
by yourself.  
The digitron displays the time  
remained (in minute) before  
the washing is finished.  
water inlet hose  
Program  
Application  
Figure 2  
Figure 1  
Normal Washing for normal laundries  
Push down the reserve  
Quick  
Quick washing for normal laundries  
Washing for light-soil a few laundries  
Washing for big and thick laundries  
button. The reserve indicator  
light is on the digitron displays  
the reserve time of finishing  
washing (in hour).The time  
remain indicator light is on,  
indicating that the reserve  
function is running.  
3.Fasten the four screws evenly. See to Figure 4.  
Posthaste  
Jean  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
Standard  
Standard saving washing for normal laundries  
If Posthaste program is selected, it will display water level 3 .  
When water level 2 is reached in water filling, it will perform  
washing while filling water. When water level 3 is reached, it will  
change to normal washing.  
Woollen Washing for the woollen laundries,  
under 2.5kg  
remark: Before installation, the threading is 4mmabove the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.  
Push the reserve button can  
display the reserve state.  
Carpet Washing for carpet and wearing bigger  
Laundries, under 3.0kg  
During operation of wash and rinse program, you can push down  
the water level button to add water. When you release the button, or  
it reaches the overflow water level, the machine will stop adding  
water.  
Saving water  
Saving washing for light-soil laundries  
About 4mm before twisting  
About less than 2mm after twisting  
The water level decided may be different from actual value because  
of the different moisture level of the laundries.  
Screw nut  
Figure 5  
Figure 4  
Figure 6  
 
4 Use the operation button  
Description of operation button  
Connection between the water inlet hose and the washer  
a
Indicator mode and meaning  
1.Do not take off the water absorption cushion. Please check if the  
nut of the water  
cushion is dropped or damaged before each usage. If it happens  
inlet hose  
please contact our after-sale department immediately.  
Flashing, indicating the running program  
On, indicating the program about to run or the selection mode  
2 .Put the nut of the water inlet hose on the valve jointer.  
3 .Fasten the nut. Swing it gently to confirm if it's suitable.  
jointer of the  
water inlet valve  
water absorption  
cushion.  
"START/PAUSE" button  
After the poweris switched on, press it to  
start the machine  
During working, push it to pause.  
During pause, push this button to restart  
and go on working  
Wash/spin  
speed  
Wash  
Spin  
Rinse  
Connection between the jointer of the water inlet hose and the water inlet hose  
Soak  
1.Push down the slider. Insert the water inlet hose into the jointer.  
the jointer of the  
water inlet hose  
Overflow  
Locking level  
Slider  
2 Hang the lock lever to the jointer. Release the slider till a click  
sound is heard.  
SPIN  
SPEED  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
"SPIN/SPEED " button  
Press the Spin/Speed button to  
select a spin procedure.  
The button can beused to select  
the desired spin time(1,3,5,7  
minutes )from the Normal program  
or the Jean program.  
The button is unavailablefrom the  
Saving,quickwash,posthaste Standard,  
Carpet, Woollen programs.  
"SOAK "button  
"WASH/SPEED " button  
"RINSE" button  
Press the Soak buttonto select a soak  
procedure.  
Press the Washbutton to select a  
wash procedure.  
The button can beused to select  
the desired wash time(0,6,9,12,15  
minutes) from the Normal and  
Jean program.  
The button is unavailable from the  
Saving,quickwash,posthaste Standard,  
Carpet, Woollen programs.  
For the Normal Jean program,  
press the button for2 seconds to  
start wash speed selection.The  
speed from 1 to4 is available for  
selection. The default value is 2.  
Press the Rinse buttonto select a  
rinse procedure.  
The button can beused to select the  
desired soak time( 10,20 minutes)  
from the Normal andComforter  
programs.  
The button can beused to select  
the desired number ofrinse cycles,  
(0, 1, 2 ,3 times )from theNormal  
program or the Jeanprogram.  
While the "Overflow" digitron is  
lighting,the program of theoverflow  
rinse has been selected.  
The button is unavailablefrom the  
Saving,Speedily, Standard,Woollen,  
Carpet and Delicate programs.  
For the Normal orJean program,  
press the button for2 seconds to  
start spin speed selection. The  
speed from 1 to4 is available for  
selection. The defaultvalue is 2.  
The button is unavailable from the  
Saving,quickwash,posthaste Standard,  
Carpet, Woollen programs.  
Dismantle the water inlet hose  
1. Close the water faucet.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
hose.  
Locking level  
If the machine is used frequently, the jointer of the water inlet hose can be  
on the faucet to prevent damaging the fixing screw.  
Slider  
kept  
 
1 Preparation before washing  
2 Put in the laundries  
Preparation before washing  
1.Connect the water inlet hose.  
The capacity of washing of the machine refer to the largest weight of the  
standard laundries under dry condition that can be washed in one  
time. Laundries quantity in one washing cycle shall be lower than  
the standard capacity. The largest capacity of this machine is 7.0 kg.  
The thickness ,size , type of the cloth will influence the actual washing capacity.  
It is suitable to put in reasonable amount of laundries and the laundries can be turned  
round in washing for one time washing.  
2.Confirm that the washing machine is earthed  
reliably. Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose.  
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid  
splashing of water.  
3 Usage of the detergent  
Control panel seat  
Washing powder inlet  
Liquid detergent inlet  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Detergent box  
Pay attention to followings before washing the laundries  
How to use softener  
How to use washing powder  
See to the manual of softener for the usage and dosage.  
When adding softener into the softener inlet of washing  
powder box, note that it shall not exceed the lower side  
of the cap.  
Do not leave the softener for long period after adding it  
into the box. Otherwise it may be solidified and block the inlet.  
As the softener is easy to solidify, please clean the box  
frequently.(You shall clean it each time you use reserve  
function).  
Clear the pocket.  
Take out the coins ,  
sand, hairpins etc.  
Confirm if there's  
special requirement  
for the laundries.  
The quantity of the  
laundries shall not  
exceed the rated  
value. The big  
laundries like the  
jeans shall be put  
in loosely.  
Fasten the buttons  
and zippers.  
When the pulsator is  
running ,the buttons of  
the laundries may cause  
noise. For the sake of  
discretion ,please put  
the laundries with  
buttons into other  
It is suggested to add washing powder into the box  
directly under fuzzy program and reserve program.  
Dissolve directly inside the washing machine: (not  
applicable for fuzzy and reserve program)  
1.Add some water(select " 1 " water level).  
2.Add washing powder. Run for about 30s to fully dissolve  
laundries.  
Before use softener, you must select to sterilize function  
Powder. Then push the"START/PAUSE" button.  
the  
3.Put in laundries. Select suitable water level. Push the  
Button again.  
"START/PAUSE"  
How to use whitener  
Quick dissolving of washing powder:  
1.Prepare warm water of 30 C and container.  
2. Add washing powder while stirring to dissolve it completely.  
When choosing the " No detergent" program, the usage of  
softener or whitener is same as using detergent.  
Please add suitable washing powder as per the laundries  
quantity, the set water level and water quantity.  
If you select "Speedily" program, it is suggested to use  
liquid detergent instead of washing powder to guarantee  
the washing effect.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries with unfast color from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
g. For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into  
mesh bag for washing.  
Add water to stipulated level. Dilute the whitener with container,  
and then pour it into the liquid whitener inlet slowly.  
Laundries with color or pattern is not colorfast, thus not applicable.  
The whitener shall not touch laundries directly.  
See to the manual of whitener for the usage and dosage.  
For whitener in powder, dissolve it before use.  
It is not recommended to use rich-foam washing powder.  
Washing powder with poor quality or long-time storage may  
get caked. Please clean the detergent box duly in usage.  
 

Hamilton Beach Mixer 840126200 User Manual
Hasbro Games 03934 User Manual
Honeywell Personal Computer CV31 User Manual
Honeywell Portable Radio TE821WD User Manual
Hotpoint Refrigerator RLA54 User Manual
HP Hewlett Packard Camcorder T200 User Manual
HP Hewlett Packard Laptop 311245 001 User Manual
HP Hewlett Packard Projector mp3320 User Manual
HP Hewlett Packard Stereo System 842M User Manual
Husqvarna Lawn Mower 2354GXLS User Manual