Haier Freezer 405SD User Manual

In sp ir e d livin g  
OPERATING MANUAL  
Deep Freezer  
QA Passed  
QA  
Passed  
HDF-245SD / 285SD  
HDF-345SD / 405SD  
Please read this manual  
carefully before use.  
HNR Company (Pvt) Ltd.  
Head Office : 63/B, Mega Tower Main Buleward, Gulberg-III, Lahore.  
UAN: 11 11 HAIER (42437) Tel: 042 - 35879105 - 7  
Retain it for future reference.  
Warranty Card inside.  
 
Important Safeguards  
Table of Contents  
Read all instructions before using this  
appliance. When using this appliance,  
always exercise basic safety  
precautions,including the following.  
-1  
PAGE  
Parts  
1
Important Safeguards  
Electric Control Panel  
Freezer Installation  
Energy Saving Tips  
Operating the Freezer  
Care and Cleaning  
Defrosting  
2-4  
5
1)  
Use this appliance only for its  
intended purpose as described in  
this use andcareguide.  
-2  
-3  
6
2)  
This freezer must be properly  
installed in accordance with the  
installation instructions before it  
is used. S ee grounding  
instructions in the installation  
section.  
7
8-9  
10  
3)  
4)  
Never unplug your freezer by  
pulling out the power cord.  
Always grip plug firmly and pull  
straight out from the power  
socket.  
11  
-4  
-5  
Useful Hints  
12  
Troubleshooting  
13-15  
Repair or replace immediately all  
electric service cords that have  
become frayed or otherwise  
damaged. Do not use a cord that  
shows cracks or abrasion  
damage along its length or either  
the plugorconnector end.  
Parts  
Hinge  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
5)  
Unplug your freezer before  
cleaning or before making any  
repairs.  
-6  
Sealing gasket  
Food Basket  
Drainage Plug  
Ventilation grill for compressor  
Lock  
Note: If for any reason this product  
requires service, we strongly  
recommend that a certified technician  
performs theservice.  
6)  
Do not use any electrical device  
or any sharp instruments in  
defrosting your freezer.  
-7  
-8  
Light  
7)  
If your freezer is not being used,  
we recommend that you remove  
the doors. This will reduce the  
possibility of danger tochildren.  
Control  
1
2
 
Important Safeguards  
Important Safeguards  
8)  
After your freezer is in operation,  
d o n o t t o u c h t h e c o l d  
s u r f a c e i n t h e f r e e z e r  
compartment, particularly when  
hands are damp or wet. Skin  
may adhere to these extremely  
cold surfaces.  
-8  
For future Reference please  
savethese instructions.  
DANGER  
Risk of child entrapment.  
Before you throw away your  
old freezer, take off the door.  
Leave the shelves in place so  
that children may not easily  
climb inside.  
-9  
9)  
Do not refreeze foods, which  
havebeenthawedcompletely.  
10) This freezer should not be  
recessed or built in an enclosed  
cabined. it is designed for  
freestanding installationonly.  
-10  
Warning: please take care of  
children, to keep lands and  
feet from punching and gaps in  
cabin or back which made by  
metal, in order to avoid  
accident.  
11) Do not operate your freezer in the  
presenceofexplosive fumes.  
-11  
-12  
12) Use of any extension cord is not  
recommended.  
13) Remove all packing before  
commencing freezeroperation.  
-13  
-14  
Thank you for using our  
product. This easy to use  
manual will guide you in  
getting the best use of your  
freezer.  
14) Do not overfill the freezer. Where  
possible, large blocks of meat  
should be cut and wrapped in  
smaller pieces. Space should be  
left between packages of food to  
enableairto circulateat alltimes.  
Remember to record the  
model and serial number.They  
are on a lable in back of the  
freezer.  
15) Never place combustible,  
explosive or volatile liquid, gas or  
other materials inthe freezer.  
-15  
-16  
16) Do not leave beverages such as  
beer, soft drinks or other liquids,  
packaged in glass containers in  
the freezer, such liquids will  
expand upon freezing and can  
cause the glass tobreak.  
Model number  
Serial number  
Date of purchase  
17) Do not put water directly in to the  
tank of the freezer.  
-17  
3
4
 
Electric Control Panel  
Freezer Installation  
The main functions of the electronic  
controlpanelare:  
1) The freezer is designed for free-  
standinginstallation only.  
2) Install the freezer on  
a
base  
-1  
1)  
The control panel is numbered  
1,2,3,4,5,6,7. This refers to the  
temperature on the inside of  
the freezer. The temperature is  
lowered by turning the dial in  
clockwisedirection.  
strong enough to support it when  
fully loaded. Ensure the freezer is  
on a stable surface to minimize  
noise andvibration.  
3) When moving the freezer, never  
tilt at an angle more that 45 as  
t h i s c o u l d d a m a g e t h e  
compressor and freezer system. If  
the freezer is tilted over 45 , or has  
been stored on its side, allow the  
freezer to stand upright for at least  
24' hours prior to plugging it back  
in, this will allow the refrigerant to  
settle.  
Refrigerate: When dial is near the "1"  
position, the interior average  
t e m p e r a t u r e o f f r e e z e r i s  
approximately 10 C~ -2 C.  
Freeze: When dial is near the "2-7"  
position, the interior average  
t e m p e r a t u r e o f f r e e z e r i s  
approximately -2 C~ -26C.  
4) Install the freezer in  
a
well-  
ventilated area away from any  
heat source or direct sunlight. Air  
must be allowed to circulate freely  
around the freezer.Allow at least 3  
inches (7.5 cm) of clearance  
spacefor the top, back and sides.  
When you change the dial from  
refrigerate function to freeze function,  
the food in the freezer should be taken  
out to avoid freeze.  
5) Install the freezer in a dry place  
to prevent rust from forming on  
the compartment body and to  
avoid the risk of damaging the  
electric insulation.  
2)  
The green lamp indicates that  
the appliance is connected to a  
power supply. The green lamp  
illuminates when the freezer is  
connected to an appropriate  
power supply.  
-2  
E l e c t r i c C o n n e c t i o n a n d  
Precautions  
1) IMPORTANT: For personal safety,  
this appliance must be properly  
earthed.  
3)  
The yellow lamp illuminates  
when the "Quick Freeze"  
function is working. Quick  
-3  
-4  
2) The rated voltage for this  
appliance is 220V to 240V. In the  
event that your regional power  
supplier connot meet this  
requirement, please use a safe  
and reliable automatic voltage  
regulatorwitha minimum output of  
500W to avoid damaging the  
compressor.  
freezingcan retainthe original taste  
of the food.  
4)  
All control equipment is  
installed on the control panel  
situated on the exterior of the  
freezer.  
5
6
 
Operating Your Freezer  
Energy Saving Tips  
3) A 13 Amp, 3 Pin Plug and 5 Amp  
fuse only must be used for this  
freezer to avoid serious damage.  
The plug should always be wired  
in accordance with the following  
codes.  
Voltage supply  
To start your freezer it must be  
connected to a 220 volt, 50 Hz A.C.  
power supply. Failure to do so may  
invalidatethe guarantee.  
Green andYellow Earth(E)  
Once the freezer is properly pluggedin,  
the green power light will illuminate,  
indicating that the freezer is in  
operation.  
Blue  
Brown  
Neutral (N)  
Live(L)  
It is safest to consult a qualified  
electricianat all times.  
Temperature/ColdControl  
4) In the event of an electrical short  
circuit, grounding reduces the risk  
of electric shock by providing an  
escape wire for the electrical  
current. This appliance is fitted  
with a cord having a grounding  
wire with a grounding plug. This  
plug must be plugged in to an  
outlet that has been properly  
installed and grounded.  
The temperature control dial has  
settings from "1"-"7". Where "1" is the  
warmest and "7" is the coldest  
temperature setting. Turn the control  
knob to higher numbers for colder  
temperatures.  
During extremely hot weather and  
frequent lid opening, it is advisable to  
select a higher setting to ensure that  
food remainsfrozen.  
5) Consult a qualified electrician or  
service centre if the grounding  
instructions are not completely  
understood or if any doubt exist as  
to whether the appliance is  
properly grounded.  
Initially, set the temperature control  
knob to the "5" setting by turning the  
knob in a clock wise direction. After 30  
minutes, you should notice an obvious  
decrease in the interior temperature of  
the freezer.  
EnergySavingTips  
*
Do not place your freezer nest to a  
heating vent, cooker, in direct  
sunlight or in the vicinity of any  
otherheat-producing source.  
Let the freezer to run for a further 12  
hours before placing your food inside,  
allowing some space between items to  
allow air to circulate properly. After  
using the freezer for 24 hours, adjust  
the temperature control to the setting  
that is best suited toyourneed.  
*
*
*
Deep the door closed as much as  
possible, especially in hot and  
humidweather.  
Defrost the freezer every few  
months or when the frost becomes  
6mm (1/4") thick or more.  
PowerCut  
If you unplug your freezer or  
experience an electrical outage, ideally  
wait five minutes before plugging the  
appliance back in.  
Cover foods securely to reduce  
moisture build up inside the  
freezer.  
7
8
 
Operating Your Freezer  
Care & Cleaning  
Fast/Quick FreezeSwitch  
IMPORTANT  
Before Cleaning, always switch refrigeratoroff and remove plug from the power supply.  
Your freezer is equiped with  
a
Fast/Quick Freeze switch (amber) for  
quicker freezingof freshfood.  
PART  
HOW TO CLEAN  
Exterior  
* Wash using warm water and a mild detergent e.g. soap or  
dishwashing liquid.  
* Rinse through, wipe clean and dry.  
* DO NOT USE HARSH CLEANERS OR ABRASIVES.  
* Waxing is recommended if humidity is high to prolong the life  
of your freezer. Use a good quality car wax or appliance wax.  
DO NOT USE WAX ON PLASTIC PARTS.  
It is recommended that the Fast/Quick  
Freeze switch be switched on 12 hours  
in advance, before loading the freezer  
with a lot of fresh food and left on for 24  
hours after loading. When all freezing  
is complete, switch off the Fast/Quick  
Freezeswitch.  
* DO NOT USE BLEACH OR PETROL BASED PRODUCTS TO  
CLEAN YOUR FREEZER.  
* DO NOT PLACE HOT OR HEAVY OBJECTS ON THE  
SURFACE OF THE FREEZER TO AVOID DAMAGING THE  
SURFACE OR DEFORMING THE GASKET.  
Food Basket  
The freezer is equipped with three  
removable food baskets for storing  
items at a higher level. Where food is  
dripping, place it into a tray before you  
start freezing, toprevent contaminating  
otherfoodalready in thefreezer.  
Interior  
* Wash with a warm water solution containing either a mild  
detergent or baking soda solution (2 table spoons/30g baking  
soda to 1 liter warm water).  
* Wipe clean and dry.  
Lid Liner /  
Gasket /  
* Wash using only warm water, a mild detergent.  
* Rinse and dry.  
Food Basket  
* Liquids such as oil and juice stick easily to the gasket to clean,  
wipe with lukewarm water to extend the life of the plastic.  
Lamp Control Switch  
The tilt switch controlling the lamp is  
inside the lid. It controls the lamp  
automatically when opening or closing  
the lid.  
LockandKey  
Those freezers which have hand locks.  
Allow you to secure the freezer  
contents from theft or to simply keep  
children out of thefreezer.  
To lock the lid, close the lid securely,  
insert the key into the lock and tum  
clockwise until the lid is latched and  
locked.  
To unlock, turn the key in the opposite  
directionand removekey.  
9
10  
 
Defrosting  
Useful Hints  
Defrosting  
Pull the drain dial out and rotate it untill  
the triangle points downwards. When  
done return the triangle to the up  
position, push the dial back in and  
replace the plug inside the freezer  
compartment.  
If the frost on the freezer walls reaches  
a thickness of 6mm or greater, the  
freezer requires defrosting. It should  
not be necessary to defrost the freezer  
more than once every few months and  
the defrosting process is best carried  
out when the stock of food is at low  
level.  
Cleaningandtemperature setting  
Wipe the interior of the freezer and  
drain hole with a cloth or clean as  
described in the "Care and Cleaning"  
section of this manual. Reinsert drain  
plug and plug the power cord back into  
the power source/socket.  
Defrosting  
Before defrosting, turn the thermostat  
to the lowest temperature setting for  
about four hours. This will enable you  
to remove any remaining food from the  
freezer at its lowest temperature. Food  
removed from the freezer should then  
be warpped in several layers of  
Turn the temperature control to the  
desired setting. You may wish to use  
the Fast/Quick Freeze feature for a few  
hours and then adjust the temperature  
controltothe desired settings.  
newspaper and placed in  
a
cold  
Useful Hints  
refrigerator. Remember that any rise in  
temperature will shorten the life of the  
frozen food considerably. Thawed food  
shouldnot be re-frozen.  
*
If your freezer is to be out of service  
for any length of time, ensure that  
interior is carefully cleaned and  
dried as per the "Care and  
Cleaning" instructions given in the  
manual. Leave the lid open and  
disconnect the plug from the power  
supply.  
Once all food has been removed from  
the freezer, disconnect the power by  
removing the plug from the power  
source/socket.  
*
Hot foods should be allowed to  
cool before being placed inside  
thefreezer.  
To help remove the frost, use the  
plastic defrostingscraper provided. DO  
NOT USE SHARP OR METALLIC  
INSTRUMENTS TO REMOVE THE  
ICE. Defrosting usually takes a few  
hours. To defrost faster, keep the door  
open and place a bowel of warm water  
inside the freezer.  
*
*
Don't try to freeze too much fresh  
produceatany onetime.  
Carry out regular cleaning of the  
exterior as per the "Care and  
Cleaning" instructions given in the  
manual. This is important if the  
freezer is subjected to high humidity  
and heavycondensation.  
Drainingthe freezer  
Turn the inner plug in the bottom of the  
freezer compartment. Place a try or  
other water receptacle beneath the  
outer drain dial/plug (front lower left of  
the freezer).  
*
Bulb replacement - Always turn off  
the power supply and remove plug  
before removing light cover.  
11  
12  
 
Troubleshooting  
Troubleshooting  
Safety Notes  
Troubles/Problem  
Reasons  
Solutions  
*
When disposing of an old freezer,.  
ALWAYS remove lid as a safeguard  
against small children getting  
trappedinside.  
Green indicating  
light is off  
Power is off.  
check your main circuit.  
The plug is not inserted.  
The fuse is blown/bumt.  
The indicating lamp is out of use.  
Circuit breaker tripped.  
Insert plug and switch on socket.  
Change the fuse (5 amp)  
Change the indicating tamp bulb.  
Reset breaker.  
*
Don not store flammable or  
explosive substances in the freezer  
cabinet.  
*
*
Do not store any fizzy drinks in the  
freezer.  
Cable is damaged.  
Call electrician to repair.  
The temperature is  
not low enough.  
Temperature setting is not low enough.  
Turn dial to higher number setting.  
Do not store any liquids contained in  
glass in thefreezer.  
The freezer is in direct sunlight or  
close to a heat source.  
Change freezer location.  
Troubleshooting  
Too much food has been stored at one  
time.  
Take off some load in the freezer.  
The table below provides some  
guidance to solving an apparent minor  
operating problems that might occur  
occasionally.  
It is important to recognize that the  
following three situations are a part of  
the normal operation and use of the  
freezer.  
The door is being opened too often.  
The floor is not level.  
Keep door closed for longer.  
Too much noise/  
vibration.  
Change the position of the freezer  
until the noise level is reduced.  
Too much dust on motor fan.  
Clean the fan.  
The compressor  
works continuously.  
The thermostat setting is too low.  
Turn the dial to increase the  
temperature.  
1) There is a sound of liquid flowing in  
the system when the freezer is  
switched on.  
The quick freezing switch is on  
and the yellow lamp is lit.  
Turn the quick freeze switch to its  
normal (off) position when the  
THIS IS NORMAL AND IS THE  
SOUND OF THE REFRIGERANT  
FLOWINGTHROUGHTHE SYSTEM.  
fast/quick freeze period has finished.  
Strong odors in the  
freezer.  
Spoilt food.  
Remove spoiled food from freezer  
and any other food it has been in  
contact with.  
2) The exterior of the freezer is warm  
and the compressor is extremely hot  
and burns on touching. THIS IS  
NORMAL  
Food not wrapped correctly.  
Interior requires deaning.  
No baking soda in place.  
Ensure food with strong odor is  
tightly covered (freezer bags are best)  
Clean per "Care and Cleaning"  
instructions.  
3) There is condensation on the  
surface.  
THIS IS ESPECIALLY COMMON IN  
CLIMATES WITH HIGH HUMIDITY  
AND IS NOTADEFECT.  
Place an open box of baking soda  
inside the freezer. Replace every  
3 months.  
CLEAN THE CONDENSATION WITH  
ADRYCLOTH.  
13  
14  
 
Troubleshooting  
15  
 

Grandstream Networks IP Phone GXE502X User Manual
Grizzly Grinder G2790 User Manual
Haier Microwave Oven HGL 1770MB User Manual
Heatcraft Refrigeration Products Refrigerator BN PL0208 User Manual
Honeywell Air Cleaner F52F User Manual
Honeywell Home Security System 400 User Manual
Honeywell Thermostat CT3697 User Manual
Honeywell Ventilation Hood D896 User Manual
Hotpoint Clothes Dryer TCUD 97B User Manual
Huawei Weather Radio HG552a1 User Manual