Grizzly Brush Cutter C2314 C2317 User Manual

INSTRUCTIONS FOR  
C2314-C2317 REVERSIBLE  
STILE AND RAIL SET  
Introduction  
The Model C2314-C2317 Reversible Stile and Rail  
Sets allow you to shape ¾" material into door stiles  
and then simply reverse the cutter components to  
shape the door rails. This set comes complete with  
a ball bearing guide and shims.  
Always disconnect power  
to the machine when set-  
ting up or making adjust-  
ments. Failure to do this  
may result in serious per-  
sonal injury.  
!
212  
"
Cutting Rails  
For safety and best results, we recommend using  
a shaper with adjustable fences and a miter gauge.  
These instructions are only intended for setting up  
the cutter for counterclockwise rotation.  
1
1"  
4"  
Reversible Stile and Rail Set  
To cut the rail ends:  
1. UNPLUG THE SHAPER!  
• Failure to follow these guidelines will result  
in serious personal injury.  
• Follow the safety guidelines set forth by the  
manufacturer of the shaper.  
2. Slide the flat cutter, bearing side up, over the  
spindle as shown in Figure A.  
• DO NOT remove guards and anti-kickback  
devices from the shaper.  
• ALWAYS WEAR ANSI APPROVED EYE AND  
EAR PROTECTION when using this bit.  
• Unplug shaper before installing or adjusting  
cutter.  
Spindle Nut  
Bushing  
Profile  
Cutter  
• Always inspect workpiece for cracks, knots,  
or other imperfections that could cause the  
workpiece to kick or shatter while milling.  
• Always feed the workpiece against the cut-  
ter rotation.  
Flat  
Spindle  
Cutter  
Figure A. Set-up for cutting rails.  
These shaper bits have sharp edges. Use care  
while removing the waxy protective coating.  
Never turn on the shaper with the protective  
coating still on the bit.  
3. Place the bushing into the hole in the profile cut-  
ter and slide both onto the spindle.  
4. Thread the spindle nut against the bushing and  
tighten it with a wrench.  
-1-  
 
Adjustments  
NOTICE  
If the test pieces are not flush (Figure D) then check  
If you have never used this type of machine  
or equipment before, WE STRONGLY RECOM-  
MEND that you read books, trade magazines,  
or get formal training before beginning any  
projects. Regardless of the content in this  
instruction sheet, Grizzly Industrial will not  
be held liable for accidents caused by lack of  
training.  
the following:  
Improper Height Adjustment Shown  
We stress the importance of working with good qual-  
ity material and insuring that all pieces are machined  
the same and that all ends and edges are cut square.  
Follow all recommended safety procedures and  
always test your setup using sample pieces.  
Figure D. Improperly fitting stile and rail.  
—If the bottom edge lines up, but the top does  
not, make sure the thickness of the stile mate-  
rial is the same as the rail material.  
If this is your first time performing panel door con-  
struction, start simple by making a square door.  
Doors having more intricate designs, such as arched,  
tombstone or curved panels, should only be done  
when you are confident of your ability. If your proj-  
ect requires curved pieces then freehand shaping  
will be necessary. Remove the fence(s) and always  
incorporate the use of a starting pin or block to sup-  
port the workpiece as it is initially fed into the cutter.  
Always use some type of jig or hold-down device to  
make the operation safer and to avoid having your  
hand in close proximity to the spinning cutter.  
—If both the top and bottom edges do not line  
up as shown in Figure D, adjust the height  
of the shaper spindle, or fine tune the cutter  
height by placing the included metal shims  
between the bushing and the profile cutter.  
—If the panel wont slide into the groove in the  
stile and rails, place a metal shim between  
the guide bearing and the profile cutter as  
shown in Figure E.  
Figure F is a sample of how all the stile and rail  
pieces should fit together.  
Insert Shim  
SHIM  
When Joint Is  
Too Tight  
Figure E. Adjustment to fit panel.  
Figure F. Stile and rail assembly.  
-3-  
 

Graco Toddler Furniture 8824 User Manual
Grizzly Router T10115 User Manual
Hamilton Beach Slow Cooker 33453 User Manual
Hans Grohe Plumbing Product 32020XX1 User Manual
Hasbro Stereo Amplifier OX4 User Manual
Honeywell Thermostat 9820i User Manual
HP Hewlett Packard Power Supply UPS R1500 GENERATION 2 User Manual
Hunter Fan Fan 90401 User Manual
Husqvarna Trimmer 128LD User Manual
Impex Home Gym TSA 410 User Manual