Sylvania TV VCR Combo SRC2213B User Manual

OWNER’S  
MANUAL  
COLOR TV/VCR  
SRC2213B  
SRC2319  
13” MODEL ILLUSTRATED  
This Owner’s Manual is made of  
recycled paper.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
If you need additional assistance for set-up or operating  
after reading owner’s manual, please call  
TOLL FREE : 1-800-968-3429.  
energy efficiency. ENERGY STAR® is  
a U.S. registered mark.  
 
Please read before using this equipment  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
19.Damage Requiring Service-Unplug this TV/VCR from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR.  
c. If the TV/VCR has been exposed to rain or water.  
d. If the TV/VCR does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/VCR to its normal operation.  
14.Lightning-For added protection for this TV/VCR receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/VCR due to lightning and  
power-line surges.  
e. If the TV/VCR has been dropped or damaged in any way.  
f. When the TV/VCR exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/VCR, ask the service technician to perform routine  
safety checks to determine that the TV/VCR is in proper  
operating condition.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/VCR.  
22.Heat-This TV/VCR product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18.Servicing-Do not attempt to service this TV/VCR yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to quali-  
fied service personnel.  
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
- 3 -  
EN  
1K09  
 
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LOCATION  
For safe operation and satisfactory performance of  
your TV/VCR, keep the following in mind when  
selecting a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top and bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Unauthorized recording or use of broadcast televi-  
sion programming, video tape, film or other copy-  
righted material may violate applicable copyright  
laws. We assume no responsibility for the unautho-  
rized duplication, use, or other acts which infringe  
upon the rights of copyright owners.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR near strong magnetic fields.  
Avoid moving TV/VCR to locations where temper-  
ature differences are extreme.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR cassette holder.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a tape is played in a TV/VCR  
which has moisture, it may damage the tape and  
TV/VCR. Therefore when the condensation occurs  
inside the unit, turn the POWER button on and allow  
at least 2 hours for the unit to dry out.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
Download from Www.Somanuals.c-om4.-All Manuals Search And Download.  
EN  
1K09  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17  
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .19  
PICTURE CONTROLS . . . . . . . . . . . . . . . . . .19  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
AVOID THE HAZARDS OF ELECTRICAL  
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4  
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6  
C OPERATING CONTROLS AND FUNCTIONS 7  
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20  
NORMAL RECORDING . . . . . . . . . . . . . . . . .20  
SKIPPING UNWANTED SCENES DURING  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20  
OTR (One Touch Recording) . . . . . . . . . . . . . .20  
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21  
TIMER PROGRAM EXTENSION . . . . . . . . .22  
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9  
ANTENNA/CABLE CONNECTIONS . . . . . . .9  
INSTALLING THE BATTERIES . . . . . . . . . . .10  
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10  
CHANNEL SET UP FOR THE FIRST TIME .10  
CLOCK SET UP (AUTO / MANUAL) . . . . . .11  
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12  
DELETING (OR ADDING) CHANNEL . . . . .12  
SELECTING THE LANGUAGE . . . . . . . . . . .13  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23  
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24  
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24  
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25  
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25  
REAL TIME TAPE COUNTER . . . . . . . . . . . .25  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14  
WATCHING A TV PROGRAM . . . . . . . . . . . .14  
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14  
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27  
C CABLE CHANNEL DESIGNATIONS . . . . . .27  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
INDICE  
CONTROLES DE OPERACIÓN Y  
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30  
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28  
PREPARACIÓN DE CANALES POR  
CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31  
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
- 5 -  
EN  
1K09  
 
FEATURES  
Infrared remote control  
Bilingual on screen menu display selectable in  
English or Spanish  
Zero Return–The tape returns to counter of  
0:00:00 by rewinding or fast forwarding.  
Still–“Freeze” the picture at any time, for close  
viewing of a particular scene. Only tapes recorded  
in SLP mode will show a fairly clear picture.  
Digital Auto Tracking (DTR)–Automatically  
adjusts the tracking for each tape you play.  
Rental play mode–Improves playback picture  
quality from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a  
tape indefinitely without pressing the PLAY button.  
Time search–Let you set the TV/VCR to advance  
the tape by entering the desired playback time you  
want to skip.  
OTR (One Touch Recording)–Instant timed  
recording from 30 to 480 minutes is possible at the  
push of the REC/OTR button.  
1 Year, 8 events (including Daily and Weekly  
Timer Recording)–The built-in timer allows you to  
record up to 8 programs at different times on dif-  
ferent channels up to 1 year in advance. The Daily  
timer allows recordings to be made of daily broad-  
casts, and the Weekly timer allows recording to be  
made once a week up to the end of the tape.  
Real time counter–This shows the elapsed record-  
ing or playback time in hours, minutes, and sec-  
onds. The “–” indication will appear when the tape  
is rewound further than the tape counter position  
“0:00:00”.  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call–(A converter may  
be necessary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock  
function from a PBS broadcast station.  
Closed caption system–You may view specially  
labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Game mode–Automatically sets external input  
mode and allows TV/VCR display to be suitable  
for use with TV games.  
Auto power on and off system–Automatically  
turns on the TV/VCR when you insert the cassette,  
turns off after auto-rewind, and ejects when the  
beginning of the tape is reached.  
Auto rewind when the end of a tape is  
reached–This function doesn’t occur when using  
timer recording.  
2 Step picture search operation–You can view a  
video program at a high speed or super high speed  
in either a forward or reverse direction in LP and  
SLP mode. For SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
Auto Head Cleaner–Automatically cleans video  
heads as you insert or remove a cassette.  
Auto return–After timer recording is finished, the  
TV/VCR can return to the beginning of the record-  
ing.  
Wake up/Sleep timer–Allows you to have the  
TV/VCR automatically turn on or off at a desired  
time.  
Timer Program Extension–Allow you to shift the  
time schedule for automatic timer recording.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
2 AA Batteries  
Rod Antenna  
(13” model only)  
PART NO. (0EMN00673 or  
PART NO. (N0154UD)  
0EMN01599 or  
0EMN01755)  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
968-3429.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control. If you decide to use a universal remote control with this unit, please be aware  
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-  
versal remote control.  
Download from Www.Somanuals.c-om6.-All Manuals Search And Download.  
EN  
1K09  
OPERATING CONTROLS AND FUNCTIONS  
"
"
This manual covers 13 and 19 . The operation of the two models are exactly the same except  
"
the appearance. 13 model is illustrated in this manual.  
NOTE:  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
- TV/VCR FRONT PANEL - [Fig.1]  
VIDEO  
AUDIO  
POWER  
VOLUME  
CHANNEL  
STOP/EJECT  
REW  
PLAY  
F.FWD  
REC/OTR  
EARPHONE  
1 2 3 4 5 6 7 8 910 11 12 1314  
1 VIDEO input jack– Connect to the video output  
- REMOTE CONTROL - [Fig.2]  
jack of your video camera or another VCR.  
2 AUDIO input jack– Connect to the audio output  
jack of your audio equipment, video camera or  
another VCR.  
25  
7
WAKE-UP  
/SLEEP  
POWER  
EJECT  
3 POWER button– Press to turn TV/VCR on and  
off. Press to activate timer recording.  
X Y  
3
CHANNEL  
RETURN  
4 VOLUME  
level.  
/
buttons– Adjust the volume  
1
4
7
2
5
8
3
6
9
24  
5 CHANNEL K / L buttons– Press to select the  
desired channels for viewing or recording.  
You may display the main menu on the TV screen  
by pressing repeatedly this button on the  
TV/VCR.  
TRACKING function– Press to minimize video  
‘noise’ (lines or dots on screen) during playback  
mode. (See page 19.)  
6 Remote Sensor Window– Receives the infrared  
signals from the remote control.  
7 STOP / EJECT button (TV/VCR)– Press to stop  
the tape motion. Press in the Stop mode to remove  
tape from TV/VCR.  
15  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
23  
9
PLAY  
10  
REW  
F.FWD  
STOP  
7
SPEED PAUSE/STILL  
RECORD  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
STOP button (remote control)– Press to stop the  
tape motion.  
EJECT button (remote control)– Press to remove  
tape from TV/VCR.  
COUNTER  
RESET  
19  
20  
L button–  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
- 7 -  
EN  
1K09  
 
- REAR VIEW - [Fig.3]  
ANT.  
26  
27  
+100 button– When selecting cable channels  
which are higher than 99, press this button first,  
then press the last two digits. (To select channel  
125, first press the “+100” button then press “2”  
and “5”).  
8 REW button– Press to rewind the tape, or to view  
the picture rapidly in reverse during playback  
mode. (Rewind Search)  
s button–  
Press to select a mode from a particular menu.  
16 MENU button– Press to display the main menu on  
the TV screen.  
17 DISPLAY button– Display the counter or the cur-  
rent channel number and current time on the TV  
screen. (See page 25.)  
18 SPEED button– Press to choose the desired  
recording speed:SP/SLP.  
19 T-PROG. CLEAR button– Press to cancel a setting  
of timer program. (See page 23.)  
COUNTER RESET button– Press to reset counter  
to 0:00:00.  
20 GAME button– Set the game mode and external  
input mode at the same time. (See page 14.)  
21 TIME SEARCH button– Press to activate Time  
Search mode.  
22 PAUSE/STILL button– Press to temporarily stop  
the tape during the recording or to view a still pic-  
ture during playback.  
23 MUTE button– Mutes the sound. Press it again to  
resume sound.  
24 CHANNEL RETURN button– Press to go back to  
the previously viewed channel. For example,  
pressing this button once will change channel dis-  
play from 3 (present channel) to 10 (previously  
viewed channel), and pressing it a second time  
will return from 10 to 3.  
25 WAKE UP/SLEEP button– Sets the Wake up or  
Sleep Timer. (See page 23.)  
26 Power cord– Connect to a standard AC outlet  
(120V/60Hz).  
(for example: LANGUAGE or USER’S SET UP)  
9 PLAY button– Press to begin playback.  
K button–  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
10 F.FWD button– Press to rapidly advance the tape,  
or to view the picture rapidly in forward during  
playback mode. (Forward Search)  
B button–  
When setting program (for example: setting clock  
or timer program), press to determine your selec-  
tion and proceed to the next step you want to  
input.  
Press to determine setting modes from on screen  
menu.  
Press to select a mode from a particular menu.  
(for example: LANGUAGE or USER’S SET UP)  
11 REC button– Press for manual recording.  
OTR button– Activates One Touch Recording.  
(only on the TV/VCR)  
12 RECORD indicator– Flashes during recording.  
Lights up in the Stand-by mode for Timer  
Recording.  
13 EARPHONE jack– Connects to earphones (not  
supplied) for personal listening. The size of jack is  
1/8” monaural (3.5mm).  
14 Cassette compartment  
15 Number buttons– Press to select desired channels  
for viewing or recording. To select channels from  
1 to 9, first press the 0 button and then 1 to 9.  
27 ANT. terminal– Connect to an antenna or cable  
system.  
Download from Www.Somanuals.c-om8.-All Manuals Search And Download.  
EN  
1K09  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Dish  
VHF/UHF Antenna  
(Not supplied)  
Satellite Box or  
Cable Box  
(Not supplied)  
Rod Antenna  
(Supplied with 13” model only)  
OUT  
IN  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
or  
ANT.  
VHF/UHF  
Combiner  
(Not supplied)  
or  
or  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
VHF/UHF COMBINED ANTENNA  
VHF/UHF SEPARATE ANTENNAS  
The VHF/UHF Rod Antenna (supplied with 13”  
In some areas it will be necessary to use an outdoor  
model only) is detachable. Insert the stem of the anten- antenna.  
na into the hole on the upper-back portion of the  
CABLE WITHOUT CONVERTER/  
TV/VCR. Connect the VHF/UHF Rod Antenna or  
VHF/UHF Combination Antenna to the ANT. terminal  
of the TV/VCR as shown in the diagram above. For  
the best reception, fully extend the VHF/UHF Rod  
Antenna and make the necessary adjustments. (Avoid  
touching the top section when adjusting.)  
NOTE:  
Before plugging the Rod antenna into antenna termi-  
nal, check that the pin is not bent. If it is bent,  
straighten the pin as illustrated, then plug the pin into  
antenna terminal.  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/VCR without a converter box.  
By using this connection you can:  
1) Use the TV/VCR remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
NOTE: This unit will ONLY record and view the  
same channel.  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
Bent pin  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown here.  
Cable Plug  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR Remote Control. Unattended timer record-  
ing is limited to one channel at a time.  
(Straight pin)  
(Needs to be straightened)  
NOTE:  
The connection of an indoor antenna may not always  
give acceptable TV reception.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
- 9 -  
EN  
1K09  
 
TO RECORD A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
INSTALLING THE BATTERIES  
1. Set the TV/VCR channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Ex. CH3)  
2.Select the channel to record from your Cable  
Converter Box or Satellite Box.  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
3)Replace the cover.  
EXTERNAL INPUT MODE  
When using an external input signal (another VCR or  
video camera), connect the player’s audio/video out-  
put cables to the AUDIO IN/ VIDEO IN jacks of  
your TV/VCR. Then press the CHANNEL K or  
button until “AUX” appears on the screen.  
NOTE: “AUX” is found below the  
lowest memorized channel.  
L
AUX  
(Example: CH2)  
SET UP FOR USE  
You can program the tuner to scan all the channels you receive in your area.  
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just  
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then  
select the channel to be viewed on the Cable Box or Satellite Box.  
The tuner scans and memorizes all active channels in  
your area.  
NOTES:  
CHANNEL SET UP FOR THE  
FIRST TIME  
The TV/VCR distinguishes between standard TV  
channels and cable channels.  
1 Plug in the TV/VCR power cord  
Plug the TV/VCR power cord into a  
standard AC outlet.  
If you want to play or record a video tape  
BEFORE presetting the tuner, you must press the  
MENU button on the remote control. To preset the  
tuner again, see “CHANNEL SET UP AGAIN” on  
page 12.  
The TV/VCR may memorize TV channels as  
CATV channels if reception conditions are poor. If  
this happens, try the AUTO MEMO action again  
when reception conditions are better.  
NOTE:  
If some digits appear in the corner of  
the screen, press the POWER button  
without unplugging the power cord.  
2 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR  
5 After scanning  
3 Select “ENGLISH” or “ESPAÑOL”  
The tuner stops on the lowest memorized channel.  
If you want to recall the selected channels, you can  
select the desired channel directly with the remote  
control number buttons or CHANNEL K or L.  
– SET UP –  
Select “ENGLISH” or  
B
LANGUAGE  
“ESPAÑOL”=Spanish using the  
F.FWD/B or REW/s button. “[ ]”  
indicate the selected language.  
[ENGLISH] ESPAÑOL  
AUTO PRESET  
4 Begin auto preset  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then press the F.FWD/B button.  
– SET UP –  
LANGUAGE  
[ENGLISH] ESPAÑOL  
B
AUTO PRESET  
- 10 -  
EN  
1K09  
 
TO SELECT A DESIRED CHANNEL  
4 Select the day  
You can select the desired channel by using the  
CHANNEL K or L button on or directly pressing  
the number buttons on the remote control.  
Note for using the number buttons:  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
Press the PLAY/K or STOP/L but-  
ton until your desired day appears.  
(Example: 6th 06)  
0 5  
/
0 6 – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
When selecting cable channels which are higher  
than 99, press the +100 button first, then, press the  
last two digits. (Example: to select channel 125,  
first press the +100 button then press “2” and “5”).  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
5 Select the year  
Press the PLAY/K or STOP/L but-  
ton until your desired year appears.  
(Example: 2003)  
You must proceed single-digit channel numbers  
with a zero (Example: 02 ... 09).  
0 5  
/
0 6 TUE 2 0 0 3  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
CLOCK SET UP  
(AUTO / MANUAL)  
6 Select the hour  
Press the PLAY/K or STOP/L but-  
ton until your desired hour appears.  
(Example: 5, PM)  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
The TV/VCR clock must be set correctly before  
VCR timer recording is possible. It is suggested that  
the clock be set manually when first setting up the  
TV/VCR. Then, set to [on] the auto clock setting  
which will periodically correct the setting if neces-  
sary.  
NOTE: If you cannot receive a station with time  
signals, auto clock setting cannot be performed. Use  
manual setting only.  
0 5  
/
0 6 TUE 2 0 0 3  
HOUR  
0 5  
MINUTE  
– – PM  
:
Then, press the F.FWD/B button.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: 40)  
0 5  
/
0 6 TUE 2 0 0 3  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
MANUAL CLOCK SETTING  
Make sure ...  
8 Start the clock  
5:40 PM  
The TV/VCR is turned on.  
In the example below, the clock is to be set to:  
Press the MENU button on the  
remote control.  
DATE  
May 6th, 2003  
Although seconds are not dis-  
played, they begin counting from  
SETTING TIME 5:40PM  
00 when you press the MENU button on the remote  
control. Use this feature to synchronize the clock  
with the correct time.  
– M E N U –  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L  
button to point to “SETTING  
CLOCK”.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
NOTE:  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
ZERO RETURN  
TIME SEARCH  
Then, press the F.FWD/B button.  
TO CHANGE CLOCK SETTING  
If you want to change the clock,  
1)Follow steps [1] and [2].  
2)Select where you want to change using the  
F.FWD/B or REW/s button.  
3)Enter correct numbers using the PLAY/K or  
STOP/L button.  
– SETTING CLOCK –  
2 Select “MANUAL CLOCK  
SET”  
Press the PLAY/K or STOP/L  
button to point to “MANUAL  
CLOCK SET”.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[OFF]  
Then, press the F.FWD/B button.  
4)Press the MENU button on the remote control to  
start the clock.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
3 Select the month  
PLEASE NOTE:  
Press the PLAY/K or STOP/L  
button until your desired month  
appears. (Example: May 05)  
Then, press the F.FWD/B button.  
0 5  
/
– – – – – – – – –  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and  
press the F.FWD/B or REW/s button to turn [OFF]  
this function. Then you can manually adjust the  
clock.  
HOUR  
– –  
MINUTE  
– – – –  
:
- 11 -  
EN  
1K09  
 
AUTOMATIC CLOCK SETTING  
Make sure ...  
NOTE: During Auto Clock CH Search, the picture  
may be distorted. This is normal.  
The TV/VCR is turned on.  
Confirm the TV/VCR is receiving a RF (Radio  
Frequency) signal from either an antenna or cable  
system connection using the ANT IN jack on the  
rear of the TV/VCR.  
4 Enter the channel number that contains the  
Automatic Clock Setting Signal  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L  
button to select “SETTING  
CLOCK”.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
NOTE:  
If a cable converter box is being used, make sure it  
is powered on.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
You must use the TV/VCR remote control to per-  
form the clock setting procedure.  
If the TV/VCR is connected directly to a cable  
converter box or satellite box, the local PBS station  
must be selected on the cable box itself, and the  
TV/VCR must be set to the output channel of the  
cable converter box or satellite box (usually chan-  
nel 3 or 4), to be able to set up or correct the clock  
automatically  
Press the F.FWD/B button to  
select setting clock.  
Press the STOP/L button to select  
“AUTO CLOCK CH”.  
Press the F.FWD/B or REW/s  
buttons until you locate Auto  
Clock Set station number. See item  
3 above.  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
B
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[
45]  
[OFF]  
Press the MENU button to exit the screen.  
1 Select “SETTING CLOCK”  
5 Turn off the TV/VCR  
Press the MENU button on the  
Once the TV/VCR is turned off , it will periodically  
check and set the correct date and time.  
– M E N U –  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to select “SETTING CLOCK”.  
Press the F.FWD/B button to enter  
“SETTING CLOCK” menu.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
CHANNEL SET UP AGAIN  
TIME SEARCH  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
– SETTING CLOCK –  
2 Set “AUTO CLOCK” to [ON]  
Press the F.FWD/B button until  
AUTO CLOCK [ON] appears.  
B
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
1 Select “CHANNEL SET UP”  
[OFF]  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
B
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
3 Begin “AUTO CLOCK CH SEARCH”  
Press the STOP/L button to select “AUTO CLOCK  
TIME SEARCH  
Then, press the F.FWD/B button.  
CH SEARCH”.  
Press the F.FWD/B button.  
– SETTING CLOCK –  
The TV/VCR is now searching  
AUTO CLOCK  
[ON]  
2 Begin auto preset  
B
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
– CHANNEL SET UP –  
for the station which contain the  
auto clock set signal. The search  
for a signal may take up to 20  
seconds per channel.  
“_ _” appears at the lower left of  
the screen when the search has  
ended.  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then, press the F.FWD/B button.  
The tuner scans and memorizes all  
the active channels in your area.  
[OFF]  
ADD / DELETE CH (TV)  
AUTO PRESET  
B
– AUTO CLOCK CH SEARCH –  
08  
10  
13  
3 After scanning  
Auto Clock station- write down  
the number(s) that appear on the  
screen. These are the auto clock  
station(s) in your area. See item  
4 below.  
If no number(s) appear on the TV screen, there are  
no stations in your area which contain the Auto  
Clock signal. Auto Clock Setting is not possible.  
Please use Manual Clock Setting on page 11.  
The tuner stops on the lowest memorized channel.  
_ _  
DELETING (OR ADDING)  
CHANNEL  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
Press the MENU button to exit the screen.  
- 12 -  
EN  
1K09  
 
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
2 Select “ENGLISH” or “ESPAÑOL”  
Select “ENGLISH” or “ESPAÑOL”= Spanish using  
the F.FWD/B or REW/s button.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
3 Exit the Language mode  
Press the MENU button on the remote control to  
return to TV mode.  
ZERO RETURN  
TIME SEARCH  
Then, press the F.FWD/B button.  
NOTE: If for some reason the menu is in Spanish,  
press the MENU button on the remote control, press  
the PLAY/K button to point to “IDIOMA  
[ESPAÑOL]”, then press the F.FWD/B button, then  
press the MENU button on the remote control.  
– CHANNEL SET UP –  
2 Select “ADD/DELETE CH”  
Press the PLAY/K or STOP/L but-  
ton to point to “ADD/DELETE  
CH”.  
B
ADD / DELETE CH (TV)  
AUTO PRESET  
Press the F.FWD/B button.  
DAYLIGHT-SAVING TIME  
Select this feature and the TV/VCR’s clock automati-  
cally will advance one hour in April, then reverse one  
hour in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
First Sunday of April : At 2 AM the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
3 Enter the desired channel number  
Press the PLAY/K or STOP/L but-  
ton until your desired channel num-  
ber appears. (You can also use the  
number buttons or the CHANNEL  
K/L button to enter it) (Example:  
CH8)  
08  
ADD / DELETE  
4 Delete (or add) it from (into) memory  
Press the F.FWD/B or REW/s button. The channel  
number changes to light red. The channel is deleted  
from memory.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
To delete another channel, repeat steps [3] and [4].  
If you press the F.FWD/B or REW/s button  
again, the channel is memorized again.  
1 Select “SETTING CLOCK”  
Added channel: Light blue.  
Deleted channel: Light red.  
Press the MENU button on the  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
PICTURE CONTROL  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING  
CLOCK”.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
5 Exit the channel setup mode  
Press the MENU button on the remote control to  
returns to TV mode.  
TIME SEARCH  
Then, press the F.FWD/B button.  
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL K or L button.  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
Press the PLAY/K or STOP/L but-  
– SETTING CLOCK –  
ton to point to “D.S.T.”.  
Then, press the F.FWD/B or  
REW/s button until [ON] appears.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
SELECTING THE LANGUAGE  
Make sure ...  
B
[ON]  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
3 Exit the Daylight-Saving Time mode  
Press the MENU button on the remote control to  
return to TV mode.  
1 Select “LANGUAGE”  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
Press the MENU button on the  
remote control.  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “LANGUAGE”.  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
F.FWD/B or REW/s button.  
- 13 -  
EN  
1K09  
 
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
The TV/VCR’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a natural looking image.  
NOTES:  
1 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR.  
2 Select the channel number  
Press the CHANNEL K or L button to select your  
desired channel number or press the number buttons  
on the remote control.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be viewed must be selected  
on the cable box or satellite box.  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
Make sure ...  
TV/VCR power must be turned on.  
1 Select “PICTURE CONTROL”  
3 Adjust sound  
Press the VOLUME X or Y button  
to adjust the volume.  
Press the MENU button on the  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
B
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to ”PICTURE CON-  
TROL”.  
VOLUME 20  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
C
C
C
C
C
C
C
C
C
C
C
C
TIME SEARCH  
Then, press the F.FWD/B button.  
GAME MODE  
2 Select item you want to adjust  
Press the PLAY/K or STOP/L button until desired  
This function enables you to decrease the TV screen  
contrast and making it suitable for use with a TV  
GAME.  
control is displayed.  
BRIGHT  
CONTRAST  
NOTE: This function can not be set during recording.  
BRIGHT  
COLOR  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
TINT  
Press the GAME button on the  
GAME  
remote control. “GAME” appears  
on the screen.  
SHARPNESS  
3 Adjust the picture control  
When you press the GAME button;  
Press the F.FWD/B or REW/s button to adjust to  
The TV/VCR comes on automatically if it is off.  
The TV/VCR will be in external input mode auto-  
your desired level.  
matically.  
REW/s  
to decrease  
brightness  
to decrease  
contrast  
F.FWD/B  
to increase  
brightness  
to increase  
contrast  
BRIGHT  
TO CANCEL THE GAME MODE  
Press the GAME button or CHANNEL K or L but-  
ton on the remote control.  
CONTRAST  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
DEGAUSSING  
Magnetism from nearby appliances might affect the  
color of the TV picture.  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect  
power cord from AC outlet then reconnect it after 30  
minutes.  
to purple  
to green  
to clear  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
- 14 -  
EN  
1K09  
 
F.FWD/B or REW/s button. Press the MENU but-  
ton on the remote control to return to TV mode.  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news, pre-recorded tapes with either a dia-  
logue caption or text display.  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning  
the dialogues and the contents of news.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is used,  
usually for a second language if available.  
NOTE:  
Not all programs are broadcast with closed captions.  
Your television is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
Common signal conditions which may cause captions  
errors are listed below:  
WHEN THE CLOSED CAPTION MODE IS ON  
The On-Screen Display will disappear after 5 seconds.  
This is also true when the MUTE button is pressed,  
and when the PAUSE/STILL button is pressed  
while recording.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
V-CHIP SET UP  
V-CHIP SET UP  
Make sure ...  
TV/VCR is turned on.  
You have the TV/VCR remote control.  
1 Select “V-CHIP SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to select “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture ghosts  
INDEX SEARCH  
2 Enter Access code  
Use the numbers on the remote  
control to enter the access code.  
ACCESS CODE  
or airplane flutter.  
_
_
_
_
Playback of poorly recorded or worn VCR tapes.  
If the TV/VCR displays a black  
box on the TV screen, this means  
that the TV/VCR is set to the  
TEXT mode. To clear screen,  
select [CAPTION1], [CAPTION2]  
or [OFF].  
For the first time set-up or in the  
event the TV/VCR has lost power,  
enter the default code of the numbers: 0000.  
– V-CHIP SET UP –  
3 Select “TV RATING”  
Press the PLAY/K or STOP/L but-  
ton to select “TV RATING”.  
Then, press the F.FWD/B button.  
B
TV RATING  
MPAA RATING  
CHANGE CODE  
Make sure ...  
TV/VCR is turned on.  
– M E N U –  
1 Select “CAPTION”  
TIMER PROGRAMMING  
4 Blocking TV programs  
Press the PLAY/K or STOP/L but-  
ton to select “TV rating” that you  
wish to block.  
PICTURE CONTROL  
Press the MENU button on the  
SETTING CLOCK  
CHANNEL SET UP  
B
TV–Y  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
TV–Y7  
TV–G  
(
)
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CAPTION”.  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
TV–PG (  
)
)
)
TV–14  
(
B
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
TV–MA(  
When you select the rating catego-  
ry and turn it [BLOCK], the higher rating will turn  
[BLOCK] automatically. Also, the lower rating will  
turn [VIEW] automatically.  
2 Select your desired caption  
menu  
Press the F.FWD/B or REW/s but-  
ton until your desired caption menu  
appears. ([CAPTION1], [CAP-  
TION2], [TEXT1] or [TEXT2])  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
When you turn “TV-Y” to [VIEW], then all ratings  
will turn to [VIEW] automatically.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
B
TIME SEARCH  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
TV-Y7  
TV-G  
TV-PG  
TV-14  
Appropriate for children seven and older  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 14  
3 Exit the caption setting mode  
Press the MENU button on the remote control to  
return to TV mode.  
TO CANCEL THE CLOSED CAPTION SYSTEM  
Repeat steps [1] and [2], select [OFF] using the  
TV-MA Mature audience only  
- 15 -  
EN  
1K09  
 
a station that is not protected. If the (PROTECTED)  
appears on the screen, please change the channel to a  
station that is not protected.  
5 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
enter the setting and exit the screen.  
1)Follow steps [1] and [2].  
2)Press the F.FWD/B button to select "TV RAT-  
ING". Select a TV rating to be unblocked by press-  
ing the PLAY/K or STOP/L button.  
Then press the F.FWD/B button to unblock the  
rating.  
V-CHIP SET UP SUB RATINGS  
When you select the ratings of TV-Y7,TV-PG,TV-14  
or TV-MA you will have the option of selecting sub  
rating categories.  
3)Press the MENU button on the remote control to  
exit the screen.  
1 Select “V-CHIP SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
USER’S SET UP  
MPAA RATING SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to select “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
– M E N U –  
1 Select “V-CHIP SET UP”  
TIMER PROGRAMMING  
INDEX SEARCH  
PICTURE CONTROL  
SETTING CLOCK  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to select “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
2 Enter Access code  
Use the numbers on the remote con-  
trol to enter the access code.  
(Default code is 0000.)  
ACCESS CODE  
INDEX SEARCH  
_
_
_
_
2 Enter Access code  
Use the numbers on the remote con-  
trol to enter the access code.  
ACCESS CODE  
– V-CHIP SET UP –  
3 Select “TV RATING”  
Press the PLAY/K or STOP/L but-  
ton to select “TV RATING”.  
Then, press the F.FWD/B button.  
B
TV RATING  
MPAA RATING  
CHANGE CODE  
_
_
_
_
– V-CHIP SET UP –  
3 Select “MPAA RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “MPAA RATING”.  
Then, press the F.FWD/B button.  
TV RATING  
MPAA RATING  
CHANGE CODE  
B
4 Selecting Sub-Ratings”  
Press the STOP/L button to select  
the sub-rating you wish to block.  
Then, press the F.FWD/B button.  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
B
When you select [TV-Y7]:  
Press the STOP/L or PLAY/K button to select  
“FV” (Fantasy Violence).  
Then, press the F.FWD/B button to select  
[BLOCK] or [VIEW].  
When you select [TV-PG], [TV-14] or [TV-MA]:  
Press the STOP/L or PLAY/K  
4 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
G
[VIEW]  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
Selection  
G
Rating Category Explanations  
General Audience  
button to select “D”(Suggestive  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
Dialog), “L”(Coarse Language),  
“S”(Sexual Situation), or  
“V”(Violence). Then, press the  
F.FWD/B button to select  
[BLOCK] or [VIEW].  
Note: When you select [TV-MA],  
“D” does not appear on the TV  
screen.  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
NC-17  
X
(
)
[VIEW]  
[VIEW]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
Mature audience only  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “G” to [VIEW], then all ratings  
will turn to [VIEW] automatically.  
The sub-ratings which set to [BLOCK] appears  
next to the rating category in the TV rating menu.  
5 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
enter the setting and exit the screen.  
5 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
enter the setting and exit the screen.  
CHANGING V-CHIP BLOCKED PRO-  
GRAMMING  
Note: To change the rating, the TV must be turned to  
- 16 -  
EN  
1K09  
 
CHANGE ACCESS CODE  
4 Enter New code  
Use the number buttons to enter  
your desired access code in the  
NEW CODE space. Then enter the  
same code in the CONFIRM  
CODE space. V-CHIP SET UP  
screen appear on the screen.  
To change access code, follow the steps.  
NEW CODE  
X X X X  
CONFIRM CODE  
1 Select “V-CHIP SET UP”  
Press the MENU button on the remote control.  
Press the PLAY/K or STOP/L button to select “V-  
CHIP SET UP”.  
_
_
_
_
If you enter wrong code, repeat step 4, making sure  
you enter the same new code exactly in the confirm  
code space.  
Then, press the F.FWD/B button.  
ACCESS CODE  
2 Enter Access code  
Use the number on the remote con-  
trol to enter the access code.  
The default code is 0000.  
_
_
_
_
5 Exit the V-Chip setting mode  
Press the MENU button on the remote control to exit  
the screen.  
Note: If you unplug the power code or power failure  
occurs, the changed access code will be lost and will  
return to default (0000). Change your access code  
again as necessary.  
– V-CHIP SET UP –  
3 Select “CHANGE CODE”  
Press the PLAY/K or STOP/L but-  
ton to select "CHANGE CODE".  
Then, press the F.FWD/B button.  
TV RATING  
MPAA RATING  
CHANGE CODE  
B
PLAYBACK  
This TV/VCR will operate with any cassette that has the  
mark. For best results, we  
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
PRECAUTIONS  
INSERTING A CASSETTE  
Avoid moisture. Moisture condensation may occur  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the TV/VCR. The  
TV/VCR will automatically turn on.  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR, wait until the tape has warmed to  
room temperature and the moisture has evaporated.  
Window  
Avoid extreme heat, high humidity and magnetic  
fields.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
WRONG  
CORRECT  
NORMAL PLAYBACK  
AUTO REPEAT PLAYBACK  
Make sure ...  
The TV/VCR has the auto repeat function that allows  
you to repeat a tape indefinitely without touching the  
PLAY button.  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part, which is blank for more than  
10 seconds.  
TV/VCR power must be turned on.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR will start playback automatically.  
2 To begin playback  
B
PLAY  
Press the PLAY button.  
Note: If any menu is activated on  
the screen, the PLAY button does  
not function. Press the MENU but-  
ton to clear the menu. then, press  
the PLAY button.  
1 Select “USER’S SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
STOP  
3 To stop playback  
Press the STOP button when play-  
back is completed.  
 
- 17 -  
EN  
1K09  
USER’S SET UP  
2 Select “ALLor “BLANK”  
Press the PLAY/K or STOP/L but-  
ton to point to “REPEAT PLAY”.  
Press the F.FWD/B or REW/s  
button repeatedly until your  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point at which you want to review.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
2 Reset the counter to 0:00:00  
Press the COUNTER RESET button repeatedly.  
desired selection [ALL] or [BLANK] appears.  
3 Exit the Repeat Play setting  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
Press the STOP button when recording or playback  
is completed.  
Press the MENU button on the remote control to  
return to the TV mode.  
4 Start playback  
Press the PLAY button to start the Repeat Play.  
”REPEAT PLAY B” appears.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR.  
4 To activate “ZERO RETURN” mode  
Press the MENU button on the remote control.  
Press the PLAY/K or STOP/L button to point to  
“ZERO RETURN”.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
Then, press the F.FWD/B button.  
The counter will appear on the TV  
screen.  
LANGUAGE [ENGLISH]  
The tape will automatically stop  
CAPTION [OFF]  
when the counter returns to  
0:00:00.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
TO CANCEL THE REPEAT PLAY MODE  
V-CHIP SET UP  
B
ZERO RETURN  
TIME SEARCH  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
TIME SEARCH  
The Time Search function makes it possible to quick-  
ly advance the tape to your desired position simply  
by entering the exact amount of playback time you  
want to skip.  
SEARCH  
PICTURE SEARCH  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
1)You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD or REW button during playback. (in the  
SP / LP / SLP modes)  
NOTES:  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
This function will not operate in recording mode.  
In the example below: To watch a program after 2  
hour 50 minutes from the present position, in either  
direction.  
2)Press it again and the TV/VCR will now search in  
super high speed. (in the LP / SLP modes only)  
NOTE: Tapes recorded in the SP or LP mode will  
display a noise bar on the TV screen and the pic-  
ture may revert to Black and White. This is normal.  
3)Press the PLAY button to return to normal speed.  
1 Insert a tape.  
2 Select “TIME SEARCH” mode  
Press the TIME SEARCH button (with each push it  
will increase by 10 minutes).  
ZERO RETURN  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
3 Enter your desired time  
Press the PLAY/K or STOP/L but-  
TIME SEARCH  
2 : 50  
ton until your desired time appears.  
(Example: “2:50” stands for 2 hours  
50 minutes)  
If you wish to cancel the Time  
Search at this point, press the  
MENU button on the remote control.  
NOTE:  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
- 18 -  
EN  
1K09  
 
PICTURE CONTROLS  
TRACKING ADJUSTMENT  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
4 Begin Time Search  
By pressing the REW/s or F.FWD/B button, the  
TV/VCR will rewind or fast forward to the specified  
point.  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
TO CANCEL THE TIME SEARCH at  
this point  
Press the STOP/EJECT button on the TV/VCR or  
the remote control. This will delete the selected  
time.  
However when playing pre-recorded tapes or tapes  
recorded on units other than your own, noise lines  
(black and white streaks) may appear on the play-  
back picture. If this occurs, you can adjust the  
tracking control manually by pressing the CHAN-  
NEL K or L button until the streaks disappear. To  
return to the DTR function, stop the tape once and  
start playback again.  
RENTAL PLAYBACK  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
STILL PICTURE  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE/STILL  
button during playback. Only tapes recorded in the  
SLP mode will show the least amount of lines.Press  
the PLAY button to return to playback.  
NOTES:  
Usually there will be video “noise” lines (black  
and white streaks or dots) on the screen. This is  
normal.  
1 Select “USER’S SET UP”  
Press the MENU button on the  
remote control.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
TIME SEARCH  
If the tape was originally recorded in SP or LP  
mode, the still picture will be black and white in  
addition to the “noise” lines.  
This is not a fault of the machine, but is a limi-  
tation of a TV/VCR with 2 video heads.  
USER’S SET UP  
2 Set “RENTALto [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “RENTAL”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
If it is left in the Pause mode for more than five  
minutes, the TV/VCR will automatically switch to  
the Stop mode.  
3 Exit the Rental setting  
Press the MENU button on the remote control to  
return to the TV mode.  
NOISE CANCEL (in the Still mode)  
4 Start playback  
This feature allows you to reposition or reduce the  
noise lines of a still picture. Press the PAUSE/STILL  
button so that the noise lines change position on the  
screen so you can see the picture in its entirety with-  
out distracting noise lines.  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the TV/VCR.  
NOTE: This feature can be activated ONLY when  
viewing a tape recorded in the SLP mode. If the tape  
was originally recorded in the SP or LP mode, the  
still picture may revert to black and white in addition  
to the “noise bars”. This is normal.  
TO CANCEL THE RENTAL MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
VERTICAL HOLD CONTROL  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
the CHANNEL K or L button.  
NOTE:  
If there are video noise lines on the screen, reposition  
or reduce them. Refer to “NOISE CANCEL”.  
- 19 -  
EN  
1K09  
 
RECORDING  
TWO DIFFERENT TAPE SPEEDS  
ERASE PREVENTION  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).  
The table below shows the maximum recording/play-  
back time using T60, T120 or T160 tapes in each  
mode.  
You can prevent accidental  
erasing of recording by  
breaking off the tab on the  
back edge of the cassette.  
Tab  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
If you decide to record on  
the tape again, cover the  
hole with plastic tape.  
T60  
1 hour  
3 hours  
T120  
T160  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
Note: You can play back a tape recorded in LP mode  
(Long Play).  
Make sure ...  
Transparent Tape  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to  
the point at which you want to begin recording.)  
NOTE: This unit will ONLY record and view the same channel.  
SKIPPING UNWANTED  
NORMAL RECORDING  
You can ONLY watch the same TV program that is  
being recorded.  
SCENES DURING RECORDING  
Press the PAUSE/STILL button to  
PAUSE  
temporarily stop recording.  
Press the PAUSE/STILL or  
RECORD button to resume record-  
ing.  
NOTES:  
1 Select the channel to be recorded  
SP  
Press the number buttons on the  
CH 10  
remote control or the CHANNEL  
K or L button.  
Remember: If the TV/VCR is con-  
nected to a cable box or satellite  
box, the TV/VCR must be on CH3 or CH4, then the  
channel to be recorded must be selected on the cable  
box or satellite box.  
After five minutes, the TV/VCR will automatically  
switch to the Recording mode to prevent tape damage.  
If “CLOSED CAPTION (ON)” is selected, the On-  
Screen Display will appear for 5 seconds, then dis-  
appear.  
OTR (One Touch Recording)  
This function enables you to set a recording length  
simply by pressing the REC/OTR button on the  
TV/VCR.  
2 Select the tape speed  
Press the SPEED button to select  
the desired tape speed (SP/ SLP).  
SP  
Make sure ...  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
3 Begin recording  
Press the RECORD button.  
REC  
tape to the point at which you want to begin  
recording.)  
SP  
NOTES:  
This function CANNOT be done from the remote  
control.  
4 Stop recording  
Press the STOP button when recording is completed.  
Recording starts immediately when the REC/OTR  
button is pressed.  
When the REC/OTR button is pressed 18 times, the  
TV/VCR returns to the Normal Recording mode.  
- 20 -  
EN  
1K09  
 
DATE:  
July 4th, 2003  
To stop the OTR operation, press the STOP button  
on the TV/VCR or on the remote control.  
To show the remaining time, press the DISPLAY  
button on the remote control so that “OTR”  
appears on the TV screen. (It will show up  
momentarily then disappear.)  
Recording stops when 0:00 is reached.  
Please note that in the SLP mode maximum  
recording time, assuming the tape is started at the  
beginning, is 8 hours using T-160 (or 6 hours using  
T-120).  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, ejects the tape and turns itself off.  
If you press the power button during OTR, the  
TV/VCR continues recording until the selected  
length is reached.  
SETTING TIME: from 7:30PM to 8:50PM  
CHANNEL:  
TAPE SPEED:  
Make sure ...  
If a cable box or satellite box is connected with  
the TV/VCR you will be limited to record only  
one channel. And the channel selector on the  
TV/VCR must be selected to the output channel of  
the boxes CH 3 or CH 4 and then the actual chan-  
nel to be recorded must be selected on the boxes.  
Clock must be set to the correct time and date  
before setting the timer.  
TV/VCR power must be turn on to program it.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
CH61  
SP  
The channel you want to record is properly set in  
advance.  
1 Select the channel to be recorded  
Press the number buttons on the remote control or  
the CHANNEL K or L button.  
Avoid over lap of programs ...  
There is a chance that a program will not be record-  
ed when programs overlap;  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
The program with an earlier start has priority.  
Once the earliest program finishes, the overlapping  
programs will begin recording in sequence.  
The illustration below demonstrates the sequence  
of recordings.  
2 Select the tape speed  
Press the SPEED button to select the desired tape  
speed (SP/ SLP).  
Recording Sequence  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
9:30AM-12:00PM  
3 Begin OTR  
OTR(2 : 30)  
Press the REC/OTR button on the  
TV/VCR as many times as needed.  
The recording length will be deter-  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
mined by the number of times you  
SP  
press the REC/OTR button. Each  
additional push will increase the recording time by  
30 minutes. It is set up to 8 hours.  
1 Select “TIMER PROGRAMMING”  
Press the MENU button on the  
– M E N U –  
B
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
Push(es) Display  
1 push  
Recording length  
(normal recording)  
remote control.  
Confirm “TIMER PROGRAM-  
MING” is pointed by pressing the  
PLAY/K button.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
2 pushes  
3 pushes  
0:30  
1:00  
30 minutes  
60 minutes  
ZERO RETURN  
TIME SEARCH  
And press the F.FWD/B button.  
If you have not yet set the clock, “MANUAL  
CLOCK SET” appears. If so, follow stops [3] to  
[8] on page 11. Then set the timer recording.  
17 pushes  
8:00  
480 minutes  
TIMER RECORDING  
2 Select your desired program position (1~8)  
You may set the TV/VCR to start and end a record-  
ing while you are away. You can set 8 programs to  
record on specific days, daily or weekly within a 1  
year period.  
– TIMER PROGRAMMING –  
Press the PLAY/K or STOP/L but-  
ton to select the desired program  
position.  
CH DATE  
BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
Then, press the F.FWD/B button.  
In the following example, the timer is being set to record:  
- 21 -  
EN  
1K09  
 
3 Set the channel number  
Press the PLAY/K or STOP/L but-  
ton until the desired channel num-  
ber appears.  
(Example: CH61)  
Then, press the F.FWD/B button.  
8 Set end minute  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: “50” for  
8:50PM)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
B
Then, press the F.FWD/B button.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
9 Set the tape speed  
Press the PLAY/K or STOP/L but-  
ton until the desired tape speed  
appears. (Example: SP)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
Press the PLAY/K (up) button  
10 Finish setting the program  
CH DATE  
BEGIN END  
until the desired date appears.  
(Example: “7/04” for July 4th).  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/04 FRI -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
Press the F.FWD/B or REW/s button. The program  
B
is now completed.  
To set another program, repeat steps [2] to [10].  
Press the MENU button on the remote control to  
return to original mode.  
For every day recording : To record a TV program at  
the same time on the same channel every day.  
(Example: Monday through Sunday) :  
11 Set the timer  
Press the POWER button to set automatic timer  
recording. The RECORD indicator lights up.  
– TIMER PROGRAMMING –  
Press the STOP/L (down) button  
CH DATE  
BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
until “EVRY DAY” appears.  
Then, press the F.FWD/B but-  
ton.  
B
You must turn off the TV/VCR to activate automat-  
ic timer recording.  
For weekly recording : To record a  
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
TV program at the same time on the same channel  
every week. (Example: every Monday) :  
– TIMER PROGRAMMING –  
Press the STOP/L (down) button  
CH DATE  
BEGIN END  
until “EVRY” and your desired  
day of the week appear together.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
TIMER PROGRAM EXTENSION  
To shift the time schedule of an automatic timer  
recording.  
1)Press the POWER button.  
5 Set beginning hour  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “ 7, PM” for 7:30PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
2)Repeat step [1] on page 21.  
61 7/04 FRI 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
3)Press the RECORD button and select the desired  
program using the PLAY/K or STOP/L button.  
4)Press the RECORD button again.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press the  
PAUSE/STILL button on the remote control. The  
recording time returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automat-  
ically be set to the SLP mode.  
6 Set beginning minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: “30” for  
7:30PM)  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
Then, press the F.FWD/B button.  
7 Set end hour  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then, press the F.FWD/B button.  
5)Press the F.FWD/B or REW/s button to exit the  
setting menu. Then press the MENU button on the  
remote control to return to original mode.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30PM - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
- 22 -  
EN  
1K09  
 
TO CORRECT A PROGRAM  
AUTO RETURN  
While setting a program; press the REW/s but-  
ton to go back one step and enter the correct num-  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
bers using the PLAY/K or STOP/L button.  
After setting a program;  
1)Press the POWER button.  
1 Select “USER’S SET UP”  
– M E N U –  
2)Repeat steps [1] - [2] on page 21.  
3)Press the F.FWD/B button (or press the  
REW/s button to go back one step) until the  
part you want to correct begins flashing, then  
make the changes pressing the PLAY/K or  
STOP/L button.  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
4)Press the POWER button to set automatic timer  
recording.  
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
After setting a program;  
1)Press the POWER button.  
USER’S SET UP  
2 Set “AUTO RETURN” to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO RETURN”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
B
2)Repeat steps [1] ~ [2] on page 21 and select a  
program you want to cancel.  
3)Press the T-PROG. CLEAR button.  
4)Press the MENU button on the remote control to  
return to TV mode.  
While recording is in progress;  
1)Press POWER button.  
3 Auto Return will begin  
When all the timer recordings are completed, the  
TV/VCR will rewind to the beginning of the recorded  
program(s).  
NOTE:  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
2)Press the STOP/EJECT button on the TV/VCR.  
TO CHECK THE BEGIN/END TIME  
1)Press the POWER button so that the REC indicator  
goes off.  
2)Press the MENU button on the remote control.  
3)Confirm “TIMER PROGRAMMING” is pointed.  
4)Press the F.FWD/B button. The details of pro-  
grams appear on the TV screen.  
5)Press the MENU button on the remote control to  
return to TV mode.  
4 Watch the recorded program  
Press the PLAY button.  
TO CANCEL THE AUTO RETURN  
MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
WAKE UP TIMER  
The Wake Up Timer function turns on the TV/VCR  
without using the POWER button after a desired  
period of time.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
Make sure the channel you want to record is prop-  
erly set in advance.  
It is not necessary to press the RECORD button for  
timer recording.  
Recording begins automatically at the Start time.  
If you are recording using a Timer mode, you may  
NOTES:  
Use the remote control for this procedure.  
Clock must be set to the correct time before setting  
the timer.  
If you want to select [TAPE], you must insert a  
cassette tape in the TV/VCR. The tape will start  
playback automatically on your desired time.  
not operate the unit manually.  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette  
will be ejected when the POWER button is pressed  
to off.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, and the tape will be ejected.  
1 Select “WAKE UP TIMER”  
Press the WAKE UP/SLEEP button  
on the remote control once, and  
confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
WAKE UP B ON/OFF  
[ON]  
TIMER  
TV/TAPE  
TIME  
[TV]  
[12:00AM]  
- 23 -  
EN  
1K09  
 
SLEEP TIMER  
The Sleep Timer function turns off the TV/VCR  
without using the POWER button after a desired  
period of time.  
2 Select “TV” or “TAPE”  
Press the PLAY/K or STOP/L but-  
ton until to point to “TV/TAPE”.  
Press the F.FWD/B or REW/s  
button, and select [TV] or [TAPE].  
WAKE UP  
TIMER  
ON/OFF  
B TV/TAPE  
TIME  
[ON]  
[TV]  
[12:00AM]  
NOTE:  
This function does not operate during Recording  
mode.  
3 Set wake up time  
1 Select “SLEEP TIMER”  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
Press the PLAY/K or STOP/L but-  
ton until to point to “TIME”.  
Press the F.FWD/B or REW/s  
button until your desired wake up  
time appears.  
WAKE UP  
TIMER  
ON/OFF  
TV/TAPE  
B TIME  
[ON]  
[TV]  
[12:00AM]  
2 Set sleep time  
Press the PLAY/K, STOP/L,  
F.FWD/B or REW/s button until  
Each additional push will increase (or decrease) the  
time by 10 minutes.  
your desired sleep time appears.  
SLEEP TIMER [2:00]  
4 Exit the Wake Up Timer setting  
Press the MENU button on the remote control to  
return to TV mode.  
Each additional push will increase  
the time by 30 minutes up to 120 minutes.  
Press the MENU button on the remote control to exit  
the Sleep Timer setting.  
TO CANCEL THE WAKE UP TIMER  
Repeat step [1] but select [OFF].  
TO CANCEL THE SLEEP TIMER  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
To view the time left for sleep timer press the WAKE  
UP/SLEEP button twice, then press the MENU but-  
ton on the remote control to exit the sleep timer set-  
ting.  
COPYING A VIDEO TAPE  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
Connect your TV/VCR and a Source (Playing) VCR  
using the following diagram.  
1)Insert a pre-recorded video cassette into the Source  
(Playing) VCR or camcorder.  
2)Insert a blank video cassette, or one you want to  
record onto into the TV/VCR’s cassette compart-  
ment. This will become the copy.  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
[Fig.8]  
3)Press the SPEED button on remote control for the  
TV/VCR to select the desired recording speed  
(SP/SLP).  
[The TV/VCR]  
VIDEO  
AUDIO  
4)Press the CHANNEL K or L button on the  
TV/VCR until “AUX” appears on the screen.  
NOTE: “AUX” is found below the lowest memo-  
rized channel. (Example: CH2)  
5)Press the RECORD button on the TV/VCR.  
6)Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
[Ex: Source (playing)  
VCR or camcorder]  
NOTE: For best results during dubbing, use the  
TV/VCR’s front panel controls whenever possible.  
The remote control might affect the source (Playing)  
VCR’s playback operation.  
AUDIO  
Audio/Video  
adapter cable  
(not supplied)  
OUT  
IN  
VIDEO  
- 24 -  
EN  
1K09  
 
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
WHEN THE CLOSED CAPTION MODE IS OFF:  
<Off mode>  
<Counter mode>  
<Clock mode>  
Counter mode: After 5 seconds, only  
the counter remains. To clear it, press  
the DISPLAY button.  
Clock mode: After 5 seconds, only  
the clock and the channel number  
remain. To clear them, press the DIS-  
PLAY button.  
5:40PM  
CH2  
Press  
once  
Press  
once  
COUNT 0:12:34  
Press once  
ON:  
OFF mode  
Clock/Counter mode  
WHEN THE CLOSED CAPTION MODE IS  
The On Screen Display disappear after 5 seconds.  
STOP  
5:40 PM  
CH2  
This is true even if the MUTE button is pressed, or the  
PAUSE/STILL button is pressed while recording.  
SP  
COUNT 0:12:34  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
This shows the elapsed recording or playback time in  
hours, minutes, and seconds. (The displayed time  
will not change on a blank tape or blank portions on  
the tape.)The “–” indication will appear when the  
tape has rewound further than “0:00:00” on the tape  
counter.  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR will eject the tape and turn  
itself to off.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
MAINTENANCE  
back, the video heads in your TV/VCR may need  
to be cleaned.  
CABINET CLEANING  
Wipe the front panel and other exterior surfaces of  
the TV/VCR with a soft cloth immersed in luke-  
warm water and wrung dry.  
1.Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-488-1222, to  
locate an Authorized Service Center.  
NOTES:  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/VCR. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
AUTO HEAD CLEANING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
SERVICING  
Should your TV/VCR become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
488-1222, to locate an Authorized Service Center.  
Playback picture may become blurred of interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use, or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
- 25 -  
EN  
1K09  
 
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,  
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to  
remedy the problem.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Make sure the power is turned on.  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Program TV channels into TV/VCR.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the TV/VCR clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
Adjust tracking control for a better picture using the CHANNEL  
or L button on the TV/VCR.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 25.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
copy guard protection.  
Magnetism from nearby appliances or unshielded stereo speaker or  
geomagnetism might affect the color of the TV picture. Move the  
TV/VCR away from the appliances, the TV/VCR can repair itself  
automatically. If you want to repair immediately, unplug the  
TV/VCR power cord, then plug it in again 30 minutes or so later.  
No power.  
No picture and sound.  
No picture or poor picture on  
TV/VCR.  
No sound or poor sound.  
Timer recording is not possible.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
K
No picture but the audio is OK in  
playback.  
No operation by infrared Remote  
Control.  
Video or color fades in and out  
when making a copy of a video tape  
.
Different color marks on screen.  
CLOSED CAPTION PROBLEM  
My TV/VCR is showing captions  
that are misspelled.  
POSSIBLE REMEDY  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed  
as being closed captioned but none up the actual program so that additional advertising time can be  
of the captions were displayed.  
given. Since the decoder cannot read the compressed information,  
captions will be lost.  
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating  
show any captions. The tape box company accidentally left out the captioning signals during the  
mentions it being closed captioned. copying process.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode to CAPTION  
[OFF].  
- 26 -  
EN  
1K09  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
CRT :  
13 or 19 inch in-line gun, 90˚  
deflection tube  
NTSC-M  
Video input level :  
Audio input level :  
0.5~2.0Vp-p  
-15dBs  
Television system :  
Closed caption system :§15.119/FCC  
Video S/N ratio : More than 46dB  
Audio S/N ratio : More than 43dB  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
CATV  
Rotary two-head  
1/2 inch  
OTHER SPECIFICATIONS  
[ 13 inch model ]  
Power requirement : AC 120V/60Hz  
Power consumption : 65W  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
Dimensions :  
H:15-3/8” (389mm)  
W:14-1/2” (367mm)  
D:14-7/8” (377mm)  
23.1 lbs (10.5kg)  
#2~#6  
#7~#13  
#14~#69  
Weight :  
[ 19 inch model ]  
Power requirement : AC 120V/60Hz  
Power consumption : 80W  
VHF :  
5A  
MID band :  
SUPER band :  
HYPER band :  
Terminals  
A5~A1, A~I  
J~W  
W+1~W+84  
Dimensions :  
H:19-1/2” (493mm)  
W:19-3/8” (491mm)  
D:18-3/4” (475mm)  
43.0 lbs (19.5kg)  
Weight :  
Antenna input :  
VHF/UHF 75 ohms  
unbalanced  
Video input :  
Audio input :  
Earphone :  
RCA connector [ 1  
RCA connector [ 1  
1/8” monaural (3.5 mm)  
Designs and specifications are subject to change  
without notice and without our legal obligation.  
If there is a discrepancy between languages, the  
default language will be English.  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 27 -  
EN  
1K09  
 
CONTROLES DE OPERACIÓN Y SUS FUNCIONES  
Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-  
tamente la misma. En este manual se muestra el modelo de 13".  
NOTA:  
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un  
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el  
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del  
mando a distancia universal.  
VIDEO  
AUDIO  
POWER  
VOLUME  
CHANNEL  
STOP/EJECT  
REW  
PLAY  
F.FWD  
REC/OTR  
EARPHONE  
1 2 3 4 5 6 7 8 910 11 12 1314  
X
Y
)–  
4 Botones de volumen (VOLUME  
/
Ajustan el nivel del volumen.  
25  
7
5 Botones de canales (CHANNEL K/ L)–  
Púlselos para seleccionar los canales deseados  
para ver o grabar.  
WAKE-UP  
/SLEEP  
POWER  
EJECT  
3
CHANNEL  
RETURN  
Se puede mostrar el menú principal en la pantalla  
del televisor pulsando repetidamente este botón del  
televisor/videograbadora.  
1
4
7
2
5
8
3
6
9
24  
Función de seguimiento– Pulse los botones  
para minimizar el ruido de vídeo (líneas o puntos  
en la pantalla) durante la reproducción.  
6 Ventanilla sensora del mando a distancia–  
Recibe las señales infrarrojas procedentes del  
mando a distancia.  
15  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
7 Botón L–  
23  
9
Púlselo para seleccionar los modos de ajuste  
desde el menúde la pantalla.  
PLAY  
10  
REW  
F.FWD  
Púlselo para introducir dígitos cuando establezca  
un programa.  
STOP  
7
SPEED PAUSE/STILL  
RECORD  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
[ Televisor/videograbadora ]  
Botón de parada/expulsión (STOP/EJECT)–  
Púlselo para detener la cinta. Púlselo en el modo  
de parada para expulsar la cinta del  
televisor/videograbadora.  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
COUNTER  
RESET  
19  
20  
[ Control remoto ]  
Botón de parada (STOP)– Púlselo para deten-  
1 Toma de entrada de vídeo (VIDEO)–  
er la cinta.  
Conéctela a la toma de salida de vídeo de su  
videocámara u otra videograbadora.  
Botón de expulsión (EJECT)–Púlselo para  
expulsar la cinta del televisor/videograbadora.  
2 Toma de entrada de audio (AUDIO)–  
Conéctela a la toma de salida de audio de su equipo  
de audio, videocámara u otra videograbadora.  
3 Botón de la alimentación (POWER)–  
Púlselo para encender y apagar el  
8 Botón de rebobinado (REW)– Púlselo para  
rebobinar la cinta, o para ver la imagen en retro-  
ceso rápido durante el modo de reproducción.  
(Búsqueda con rebobinado)  
Botón s–  
televisor/videograbadora. Púlselo para activar la  
grabación con temporizador.  
Púlselo para seleccionar un modo desde un menú  
particular.  
- 28 -  
ES  
1K09  
 
ANT.  
26  
27  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
9 Botón de reproducción (PLAY)– Púlselo  
para iniciar la reproducción.  
99, pulse primero este botón, y luego pulse los  
dos últimos dígitos. (Para seleccionar el canal  
125, pulse primero el botón “+100” y luego el  
“2” y el “5”.)  
Botón K–  
16 Botón de menú (MENU)– Púlselo para visu-  
alizar el menú principal en la pantalla del televi-  
sor.  
17 Botón del visualizador (DISPLAY)–  
Visualiza el contador o el número del canal actu-  
al y la hora actual en la pantalla del televisor.  
18 Botón de velocidad de cinta (SPEED)–  
Púlselo para elegir la velocidad de grabación  
deseada: SP/SLP.  
Púlselo para seleccionar los modos de ajuste  
desde el menú de la pantalla.  
Púlselo para introducir dígitos cuando establezca  
un programa.  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
10 Botón de avance rápido (F.FWD)– Púlselo  
para avanzar rápidamente la cinta, o para ver la  
imagen en avance rápido durante el modo de  
reproducción. (Búsqueda con avance rápido)  
Botón B–  
19 Botón T-PROG. CLEAR– Púlselo para cance-  
lar un programa de temporizador.  
Botón de reposición del contador  
(COUNTER RESET)– Púlselo para reponer el  
contador a 0:00:00.  
Cuando establezca un programa (por ejemplo:  
para ajustar el reloj o para establecer un progra-  
ma de temporizador), púlselo para determinar su  
elección y vaya al paso siguiente que quiera  
introducir.  
20 Botón de juego (GAME)– Establece el modo  
del juego y el modo de entrada externa al mismo  
tiempo.  
21 Botón de búsqueda con tiempo (TIME  
SEARCH)– Púlselo para activar el modo de  
búsqueda con tiempo.  
Púlselo para determinar los modos de ajuste  
desde el menúde la pantalla.  
Púlselo para seleccionar un modo desde un  
menúparticular.  
22 Botón de pausa/imagen fija  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
(PAUSE/STILL)– Púlselo para detener tempo-  
ralmente la cinta durante la grabación o para ver  
una imagen fija durante la reproducción.  
23 Botón de silenciamiento (MUTE)– Silencia  
el sonido. Púlselo de nuevo para recuperar el  
sonido.  
11 Botón de grabación (REC)– Púlselo para ini-  
ciar la grabación manual.  
Botón de grabación de un toque (OTR)–  
Activa la grabación de un toque. (Sólo en el tele-  
visor/videograbadora)  
12 Indicador de grabación (RECORD)–  
24 Botón de retorno de canal (CHANNEL  
RETURN)– Púlselo para volver al canal anterior.  
Por ejemplo, pulsando una vez este botón, la  
visualización del canal cambiará de 3 (canal actu-  
al) a10 (canal anterior), y al pulsarlo por segunda  
vez, el canal cambiará del 10 al 3.  
25 Botón del temporizador despertador/para  
dormir (WAKE UP/SLEEP)– Ajusta el tempo-  
rizador para despertarse/dormir.  
Parpadea durante la grabación.  
Se enciende en el modo de espera de la grabación  
con temporizador.  
13 Toma de auriculares (EARPHONE)– Para  
conectar los auriculares (no suministrados) y  
escuchar en privado. La toma es mono y tiene un  
tamaño de 1/8”(3.5 mm).  
14 Compartimiento del videocasete  
15 Botones numerados– Púlselos para selec-  
cionar los canales deseados para ver o grabar.  
Para seleccionar canales del 1 al 9, pulse primero  
el botón 0 y luego el botón 1 a 9.  
26 Cordón de alimentación– Conéctelo a la  
toma de CA estándar (120V/60Hz).  
27 Terminal de antena (ANT.)– Para conectar  
una antena o sistema de televisión por cable.  
Botón +100– Cuando seleccione canales de  
televisión por cable cuyo número sea superior al  
- 29 -  
ES  
1K09  
 
CONEXIONES DE ANTENA/CABLE  
Desde el cable coaxil o  
caja de emisiones vía  
satélite de 75 ohm del  
sistema de Cable  
Caja de CATV  
o caja de emi-  
siones vía satélite  
(no incluído)  
Antena combinada de  
VHF/UHF  
(no incluído)  
Antena de varilla UHF/VHF  
(incluído para solamente 13”)  
OUT  
IN  
Antena VHF  
(no incluído)  
Desde el  
sistema de Cable  
Antena UHF  
(no incluído)  
O
ANT.  
Combinador de  
VHF/UHF  
(no incluído)  
O
ANT.  
Cable coaxil  
de 75 ohm (no incluído)  
O
Cable bifilar plano  
O
de los canales deberá hacerse con el convertidor de tele-  
visión por cable con el convertidor de emisiones vía  
satélite. Esto significa que los canales no podrán ser  
cambiados con el mando a distancia del  
televisor/videograbadora. La grabación inatendida se  
limita a un canal cada vez.  
PARA GRABAR UN CANAL  
CODIFICADO/DESCODIFICADO  
1. Ajuste el selector de canales del  
ANTENA COMBINADA DE VHF/UHF  
La antena de varilla de VHF/UHF (incluído para sola-  
mente 13”) es desmontable. Inserte el vástago de la  
antena en el agujero de la parte trasera superior del tele-  
visor/videograbadora.  
Conecte la varilla de antena de VHF/UHF o la antena  
combinada de VHF/UHF al terminal ANT. del televi-  
sor/videograbadora.  
televisor/videograbadora al canal de salida del con-  
vertidor de televisión por cable o del convertidor de  
emisiones vía satélite. (Ej.: CA3)  
2. Seleccione el canal que desee grabar de su conver-  
tidor de televisión por cable o del convertidor de emi-  
siones vía satélite.  
ANTENAS SEPARADAS DE VHF/UHF  
En algunos lugares será necesario utilizar una antena  
exterior.  
CABLE SIN CONVERTIDOR/DESCODIFI-  
CADOR  
Utilice esta conexión si su sistema de televisión por  
cable se conecta directamente a su  
MODO DE ENTRADA EXTERNA  
televisor/videograbadora sin convertidor.Utilizando esta  
conexión usted podrá:  
1)Utilizar el mando a distancia del  
televisor/videograbadora para seleccionar canales.  
2)Programar uno o más canales sin codificar para  
realizar la grabación automática con temporizador.  
NOTA: Con esta unidad SÓLO se podrá grabar y ver  
un mismo canal al mismo tiempo.  
Cuando utilice una señal de entrada externa (otra  
videograbadora o una videocámara), conecte los cables  
de salida de audio/vídeo del equipo de reproducción a las  
tomas AUDIO IN/VIDEO IN de su  
televisor/videograbadora. Y luego pulse el botón CHAN-  
NEL K o L hasta que “AUX” aparezca en la pantalla.  
Usted puede programar el temporizador para que explore  
todos los canales que puedan recibirse en su zona.  
CABLE CON CONVERTIDOR/DESCODIFI-  
CADOR O CONVERTIDOR DE EMISIONES VÍA  
SATÉLITE  
Si su servicio de televisión por cable le suministra un  
convertidor, o si usted utiliza un sistema de emisiones  
vía satélite, usted podrá utilizar las conexiones básicas  
mostradas aquí.  
INSTALACIÓN DE LAS PILAS  
1)Abra la tapa del compartimiento de las pilas del mando  
a distancia presionándola en el sentido de la flecha.  
2)Inserte 2 pilas tamaño “AA” en el compartimiento de las  
pilas, en el sentido indicado por las marcas de polaridad  
(+/-).  
Utilizando estas conexiones, usted también podrá  
grabar canales codificados. Sin embargo, la selección  
3)Vuelva a poner la tapa.  
- 30 -  
ES  
1K09  
 
PREPARACIÓN DE CANALES POR  
PRIMERA VEZ  
1)Enchufe el cable de alimentación del  
televisor/videograbadora en una toma de CA están-  
dar.  
NOTA: Si aparezcan algunos digitos en el rincón de  
la pantalla, pulse el botón POWER sin desenchufar  
el cable de alimentación.  
2)Pulse el botón POWER para encender el televi-  
sor/videograbadora.  
3)Seleccione “ENGLISH” o “ESPAÑOL” utilizando  
el botón F.FWD/B o REW/s. “[ ]” indica el  
idioma seleccionado.  
4)Pulse el botón PLAY/K o STOP/L para señalar  
“AUTOPRESELECCION”.  
AJUSTE DEL RELOJ  
Cerciórese...  
La alimentación del televisor/videograbadora  
deberá estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 6 de mayo de 2003  
HORA: 5:40 PM  
1)Pulse el botón MENU en el mando a distancia.  
Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE RELOJ”.  
Luego, pulse el botón F.FWD/B.  
2)Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE MANUAL RELOJ”.  
Luego, pulse el botón F.FWD/B.  
3)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el mes deseado. (Ejemplo: Mayo - 05)  
Luego, pulse el botón F.FWD/B.  
Luego pulse el botón F.FWD/B. El sintonizador  
explorará y memorizará todos los canales activos  
de su área.  
NOTAS:  
4)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el día del mes deseado. (Ejemplo: 6 - 06)  
Luego, pulse el botón F.FWD/B.  
5)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el año deseado. (Ejemplo: 2003)  
Luego, pulse el botón F.FWD/B.  
6)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca la hora deseada. (Ejemplo: 5, PM)  
Luego, pulse el botón F.FWD/B.  
7)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el minuto deseado. (Ejemplo: 40)  
8)Pulse el botón MENU en el mando a distancia.  
Aunque los segundos no se visualizan, éstos  
empiezan a contar desde 00 cuando se pulsa  
MENU en el mando a distancia. Utilice esta fun-  
ción para sincronizar el reloj con la hora correcta.  
El televisor/videograbadora distingue entre los  
canales de televisión estándar y los canales de tele-  
visor por cable.  
Si desea reproducir o grabar una cinta ANTES de  
preajustar el sintonizador, usted tendrá que pulsar  
el botón MENU en el mando a distancia. Para  
preajustar de nuevo el sintonizador, consulte  
“REPETICIÓN DE LA PREPARACIÓN DE  
CANALES”.  
La unidad de televisor/videograbadora puede  
reconocer los canales de TV como ellos de TV por  
cable a causa de los condiciones de recepción. En  
este caso, pruebe el preajuste automático de nuevo  
en los condiciones finas de recepción.  
5)El sintonizador se para en el canal memorizado  
más bajo. Si desea recuperar canales selecciona-  
dos, usted podrá seleccionar directamente el canal  
deseado con los botones numerados del mando a  
distancia o con los botones CHANNEL K o L.  
- 31 -  
ES  
1K09  
 
Get it fixed, at your home or ours!  
Your Home  
For repair in your home-of all major brand appliances,  
-
lawn and garden equipment, or heating and cooling systems,  
no matter who made it, no matter who sold it!  
For the replacement parts, accessories and  
owner's manuals that you need to do-it-yourself.  
For Sears professional installation of home appliances  
and items like garage door openers and water heaters.  
1-800-4-MY-HOME R (1-800-469-4663)  
Call anytime, day or night (U.S.A. and Canada)  
Our Home  
For repair of carry-in items like vacuums, lawn equipment,  
and electronics, call or go on-line for the location of your nearest  
Sears Parts & Repair Center.  
1-800-488-1222  
Call anytime, day or night (U.S.A. only)  
To purchase a protection agreement on a product serviced by Sears:  
1-800-827-6655 (U.S.A.)  
1-800-361-6665 (Canada)  
Para pedir servicio de reparación  
a domicilio, y para ordenar piezas:  
Au Canada pour service en français:  
MC  
1-800-LE-FOYER  
SM  
1-888-SU-HOGAR  
(1-800-533-6937)  
(1-888-784-6427)  
Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co.  
Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co.  
R
R
MC Marque de commerce / MD Marque déposée de Sears, Roebuck and Co.  
© Sears, Roebuck and Co.  
LIMITED 90 DAY WARRANTY FOR 13 INCH MODEL  
If this (product) experiences any failure due to a defect in material or workmanship within 90 days from the date of  
purchase, return it to your nearest Sears store, and it will be replaced free of charge.  
This warranty applies only if this (product) is used for private household purposes.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
FULL 90 DAY WARRANTY FOR 19 INCH MODEL  
For 90 days from the date of purchase, Sears will repair any defect in material or workmanship in this TV/VCR  
combination, free of charge. For one year from the date of purchase, Sears will supply, at no charge, replacement  
for defective parts.  
Two (2) years for Picture Tube. Certain parts are excluded from this warranty.  
The above warranty coverage applies only to TV/VCR combination which are used for private household purposes.  
TO OBTAIN WARRANTY SERVICE, SIMPLY RETURN THE TV/VCR COMBINATION TO THE NEAREST SEARS  
SERVICE CENTER IN THE UNITED STATES.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179  
For the location of a Sears Service Center in your area : 1-800-488-1222  
Printed in Malaysia  
0EMN02083  
T5407UH / T7408UJ * * * * *  
 

Shinco Air Conditioner BM User Manual
Sigma Stereo Amplifier ADA 21S User Manual
Soleus Air Dehumidifier GM DEH 30M 1GM DEH 45 1 User Manual
Sony Car Stereo System XR CA320 User Manual
Sony Computer Monitor Color Graphic Display User Manual
Sony Home Theater System CMT SX2D User Manual
Sony Speaker SA VE345 User Manual
SoundMax Home Theater System SM CDM1042 User Manual
Swisher Log Splitter LS67528S User Manual
Tanaka Portable Generator DEG 600 User Manual