Stanton CD Player S550 User Manual

USER MANUAL  
REMAIN  
REMAIN  
CONTINU  
CONTINU  
TRACK  
M
S
F
TRACK  
M
S
F
PROFESSIONAL DUAL CD PLAYER  
 
SAFETY INSTRUCTIONS  
1. Read Instructions – All the safety and operating  
instructions should be read before this product is  
operated.  
15. Object and Liquid Entry Care should be taken so  
that objects do not fall and liquids are not spilled into  
the enclosure through openings.  
2. Retain Instructions  
The safety and operating  
16. Damage Requiring Service The appliance should be  
instructions should be retained for future reference.  
All warnings on the appliance and  
in the operating instructions should be adhered to.  
serviced by qualified service personnel when:  
A. The power-supply cord or the plug has been  
damaged; or  
3. Heed Warnings  
B. Objects have fallen, or liquid has been spilled into  
the appliance; or  
C. The appliance has been exposed to rain; or  
D. The appliance does not appear to operate  
4. Follow Instructions  
All operating and use  
instructions should be followed.  
5. Water and Moisture  
The appliance should not be  
used near water - for example, near a bathtub,  
washbowl, kitchen sink, laundry tub, in a wet  
basement, or near a swimming pool, and the like.  
The appliance should be used  
only with a cart or stand that is recommended by the  
manufacturer.  
An appliance and cart combination  
should be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
normally or exhibits  
performance; or  
a
marked change in  
E. The appliance has been dropped, or the enclosure  
damaged.  
6. Carts and Stands  
17. Servicing The user should not attempt any service to  
the appliance beyond that described in the operating  
instructions. All other servicing should be referred to  
qualified service personnel.  
18. Ventilation – Slots and openings in the cabinet are  
provided for ventilation and to ensure reliable  
operation of the product and to protect it from  
overheating, and these openings must not be blocked  
or covered. The openings should never be blocked by  
placing the product on a bed, sofa, rug, or other  
similar surface. This product should not be placed in a  
built-in installation such as a bookcase or rack unless  
proper ventilation is the manufacturer’s instructions  
have been adhered to.  
7. Wall or Ceiling Mounting  
The product should be  
mounted to a wall or ceiling only as recommended by  
the manufacturer.  
8. Heat  
The appliance should be situated away from  
heat sources such as radiators, heat registers, stoves,  
or other appliances (including amplifiers) that produce  
heat.  
9. Power Sources – This product should be operated  
only from the type of power source indicated on the  
rating label. If you are not sure of the type of power  
supply to your home, consult your product dealer or  
local power company. For products intended to  
operate from battery power, or other sources, refer the  
operating instructions.  
10. Grounding or Polarization – This product may be  
equipped with a polarized alternation-current line plug  
(a plug having one blade wider than the other). This  
plug will fit into the power outlet only one way. This is  
a safety feature. If you are unable to insert the plug  
fully into the outlet, try reversing the plug. If the plug  
should still fail to fit, contact your electrician to replace  
your obsolete outlet. Do not defeat the safety purpose  
of the polarized plug.  
19. Attachments  
do not use attachments not  
recommended by the product manufacturer as they  
may cause hazards.  
20. Accessories – Do not place this product on an  
unstable cart, stand, tripod, bracket, or table. The  
product may fall, causing serious injury to a child or  
adult, and serious damage to the product. Use only  
with  
a
cart, stand, tripod, bracket, or table  
recommended by the manufacturer, or sold with the  
product. Any mounting of the product should follow the  
manufacturer’s instructions, and should use  
mounting accessory recommended by  
manufacturer.  
a
the  
21. Lightning – For added protection for this product  
during a lightning storm, or when it is left unattended  
and unused for long periods of time, unplug it from the  
wall outlet and disconnect the antenna or cable  
system. This will prevent damage to the product due  
to lightning and power-line surges.  
22. Replacement Parts – When replacement parts are  
required, be sure the service technician has used  
replacement parts specified by the manufacturer or  
have the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric  
shock, or other hazards.  
11. Power-Cord Protection Power-supply cords should  
be routed so that they are not likely to be walked on or  
pinched by items placed upon or against them, paying  
particular attention to the cord in correspondence of  
plugs, convenience receptacles, and the point where  
they exit from the appliance.  
12. Cleaning - The appliance should be cleaned only as  
recommended by the manufacturer.  
Clean by wiping with a cloth slightly damp with water.  
Avoid getting water inside the appliance.  
13. For AC line powered units - Before returning repaired  
unit to user, use an ohm-meter to measure from both  
AC plug blades to all exposed metallic parts. The  
resistance should be more than 100,000 ohms.  
23. Safety Check – Upon completion of any service or  
repairs to this product, ask the service technician to  
perform safety checks to determine that the product is  
in proper operating condition.  
14. Non-use Periods The power cord of the appliance  
should be unplugged from the outlet when left unused  
for a long period of time.  
2
 
NOTE ON USE  
Allow for sufficient heat dispersion when installed on a rack.  
Handle the power cord carefully.  
Hold the plug when unplugging the cord.  
Keep the set free from moisture, water, and dust.  
Unplug the power cord when not using the set for long periods of time.  
Do not obstruct the ventilation holes. (For sets with ventilation holes.)  
Do not let foreign objects in the set.  
Do not let insecticides, benzene, and thinner come in contact with the set.  
Never disassemble or modify the set in any way.  
MAIN FEATURES  
1) Auto cue function  
2) Real-time cue  
3) Pitch range: +/-8%, +/-12%, +/-16%  
4) Pitch display  
5) Selectable elapsed, remain and total remain time display  
6) Single / continuous  
7) Relay play allows consecutive playback during two decks  
8) Frame search  
9) 4 Scan Speeds  
10) Transport protection  
11) S/PDIF digital audio RCA coaxial  
12) 20 programmable tracks  
13) Fader start, Fader stop, (back cue), Relay playback.  
MAIN UNIT  
2
3
1
2
6
4
5
7
4
5
(1)POWER  
(2)DISC HOLDER  
(3)OPEN/CLOSE  
(4)REMOTE CONTROL CONNECTOR  
(5)AUDIO OUT L AND R  
(6)DIGITAL OUT SOCKET  
(7)VOLTAGE SELECTOR (JUST FOR DUAL VOLTAGE MODEL ONLY)  
3
 
MAIN FEATURES  
CONTROL UNIT  
2
3
4
8
9
5 6 7  
21  
10  
REMAIN  
REMAIN  
CONTINU  
CONTINU  
TRACK  
M
S
F
TRACK  
M
S
F
1
11  
12 13 15 16 18  
14  
17 19 20  
23  
23  
22  
22  
(1) SHUTTLE  
(2) OPEN/CLOSE  
(3) TIME (Time Button)  
(13) CUE Indicator  
(14) CUE (Cue Button)  
(15) +10  
(4) LCD (Liquid Crystal Display)  
(5) SGL (Single Button)  
(6) PROG.  
(7) PROGRAM Indicator  
(8) RELOOP (Reloop button)  
(9) PITCH (Pitch Indicator)  
(10) PITCH SLIDER  
(11) JOG  
(16) PLAY Indicator  
(17) PLAY/PAUSE  
(Play/Pause Button)  
/
(18) F.SKIP  
(19) IN  
(20) OUT  
(21) PITCH (Pitch Button)  
(22) CONTROL CONNECTOR  
(23) CONTROL SOCKETS  
(12) B.SKIP  
LCD  
(24)(26)(27)(28)TRACK,MINUTE,SECOND and  
FRAME Displays  
(25) BAR Indicators  
ELAPSED  
REMAIN  
SINGLE  
(29) ELAPSED Indicator  
(30) CONTINU Indicator  
(31) SINGLE Indicator  
(32) REMAIN Indicator  
(33) PITCH DISPLAY  
CONTINU  
TRACK  
M
S
F
24  
25 26  
27 28 29 30 31 32 33  
4
 
PREPARATIONS  
1. Checking the Contents  
Check that the carton contains the following items:  
1) Main unit  
2) Control unit  
3) Operating instructions (this booklet)  
4) Pair of RCA pin cord.  
5) Control cords (1 meter)  
2. Installing the Unit  
Mount the unit onto your console or rack with 19" EIA rack rails.  
CAUTION:  
zThe player will work normally when the main unit is  
mounted with the front panel at within 15 degrees of  
the vertical plane. If the unit is tilted excessively, discs  
may not be loaded or unloaded properly.  
(Figure 1)  
zThe control panel's LCDs are designed to be  
clearly visible within the angles shown in Figure 2.  
Mount the control unit so that the visual angle is within  
this range.  
Max.  
15°  
45°  
5°  
Control  
panel Button  
Main unit  
Figure 1  
Figure 2  
.
Connections  
1) Turn off the POWER switch.  
2) Connect the RCA pin cord to the input on your mixer.  
3) Connect the control cords to the REMOTE connector on the main unit.  
CAUTION:  
Be sure to use the supplied control cords. Using another type of cable may result in damage.  
Be sure the power is off when connecting the control cords. Otherwise the units may not work properly.  
NAMES AND FUNCTIONS  
Main Unit Front Panel  
(1) POWER (Power ON/OFF Switch)  
When the POWER switch is pressed, the power turns  
on.  
(4) REMOTE CONTROL CONNECTOR  
Connect this connector to the control unit using the  
included control cord.  
(2) DISC HOLDER  
(5) AUDIO OUT  
Place the discs in the holder. Press the OPEN/CLOSE  
button to open and close the disc holder.  
(3) OPEN/CLOSE  
The audio signals from each player are output from  
these jacks.  
(6) DIGITAL OUT SOCKET  
Press it to open and close the disc holder. The control  
unit also includes OPEN/CLOSE button. The disc  
holder cannot be opened during playback, so stop  
playback before pressing the button.  
The music-signal of this socket is digital. Connect the  
output to the respective input of a digital amplifier for  
example.  
5
 
NAMES AND FUNCTIONS  
Control Unit  
(1) SHUTTLE (Shuttle Dial)  
(13)CUE Indicator  
Use the dial to select the scanning direction and  
speed. The disc is scanned in the forward direction  
when the shuttle dial is turned clockwise from the  
neutral position, in the reverse direction when the  
shuttle dial in turned counterclockwise. The scanning  
speed increases when the shuttle dial is turned faster.  
When in CUE mode, the CUE indicator lights.  
(14)CUE (Cue Button)  
Pressing the CUE button during play provides a return  
to the position at which play was started. If PAUSE is  
used before CUE or a CUE POINT was set, that will  
become the cue point. Alternately pressing the Play  
button and the CUE button allows the CD to be played  
from the same position any number of times. The CUE  
LED will light up from the time the CUE button is  
pressed until the CD has reset to the position at which  
play was started. Steady lighting of this LED  
indications the ready condition. The CUE button can  
be held down to play a CD. When you release the  
CUE button it instantly returns to the CUE POINT.  
(15)+10 (Track +10 Button)  
(2) OPEN/CLOSE  
(Open/Close Button)  
Press it to open and close the disc holder. The main  
unit also includes OPEN/CLOSE buttons. The disc  
holder cannot be opened during playback, so stop  
playback before pressing the button.  
(3) TIME (Time Button)  
Press this button to switch the time display among the  
elapsed time and remaining time and total remaining  
time of the disc.  
Use the button to skip ahead 10 tracks.  
(16)PLAY Indicator  
(4) LCD  
(5) SGL (Single Button)  
The PLAY indicator lights during play mode.  
(17)PLAY/PAUSE Button  
Press it to switch the single and continuous play  
modes. The SINGLE mode is indicated by the  
SINGLE indicator on the LCD and continuous mode is  
indicated by the CONTINU indicator on the LCD.  
(6) PROG (Program Button)  
Press the PROGRAM button, the player will enter the  
program mode and stop the CD playback.  
(7) PROGRAM Indicator  
Use the button to start playback. Press once to start  
playback, once again to set the pause mode, and  
once more to resume playback.  
(18)F. SKIP  
Use these buttons to skip to the next CD track.  
(19)IN  
This allows you to set the cue point without stopping  
the play back. This button also sets the beginning of a  
loop.  
The PROGRAM LED lights when program mode is set.  
(8) RELOOP  
If a Loop has been made, but the CD Player is not  
actively in Loop mode, press the RELOOP button to  
reactivate the loop mode. To exit loop, press the OUT  
button.  
(20)OUT  
Used to set the ending when looping music. The  
player will start to loop continues until you press this  
button again to exit.  
(9) PITCH Indicator  
(21)PITCH (Pitch Button)  
When the indicator lights, the pitch adjustment is  
enabled.  
(10)Pitch Slider  
Press PITCH button to switch on/off pitch.; hold the  
PITCH button down for more than 0.6 sec to switch  
pitch in +/-8% / +/-12% / +/-16%.  
Use the slider to adjust the CD pitch. Slide up to  
decrease the pitch, down to increase the pitch.  
(11)JOG (Jog Dial)  
When the dial is turned during CD pause, the point at  
which the sound is being produced mover by a  
number of frames corresponding to the number of  
clicks. Clockwise moves the point forward,  
counterclockwise moves the point backward.  
(12)B. SKIP  
(22)CONTROL CONNECTOR  
Connect this connector to the REMOTE connector on  
the main unit using the included control cord.  
(23)CONTROL SOCKET  
Via the Control socket, the respective CD-player can  
be remotely controlled. If you are using a mixer with  
fader start-function connect the player with the Control  
Out-socket. Please note that these sockets must  
never be connected with any voltage.  
Use these buttons to go back to the beginning of the  
current track or select a previous track for playing.  
LCD  
(24) ~(27)TRACK, MINUTE, SECOND and FRAME  
Displays  
(30) CONTINU Indicator  
When the indicator lights, the function will cause the  
unit to play continuously.  
(31) SINGLE Indicator  
These displays indicate information for the CD’s  
current position and time.  
When the indicator lights, playback will stop at the  
beginning of the next track.  
(32) REMAIN Indicator  
It indicates that the time shown on the display is the  
remaining time of playing track.  
(33) PITCH DISPLAY  
(28) BAR Indicator  
These ten indicators provide a visual display of the  
approximate position of the pickup within the current  
track.  
(29) ELAPSED Indicator  
It indicates that the time shown for the display is the  
elapsed time.  
It shows the BPM change range, the BPM changes  
within a range of +/-12%.  
6
 
OPERATIONS  
1. Opening and Closing the Disc Holder  
zꢀ Turn the unit power on. Press the OPEN/CLOSE button to open the disc holder. OPEN/CLOSE buttons are  
provided on both the main unit and control unit.  
zꢀ The disc holder cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE  
button is pressed accidentally. Stop the playback first, then press the OPEN/CLOSE button.  
2. Loading discs  
™ꢀ Hold the disc by the edges and place it in the disc holder, then press the  
OPEN/CLOSE button again to close the disc holder. The unit will show the total  
track number and the total playing time for about 2 seconds then enter the cue  
condition, the cue point will be set to the music starting point of the first track  
automatically.  
Figure 2-1  
CAUTION:  
zDo not place any foreign objects in the disc holder, and do not place more than one disc in the disc holder at a time.  
zDo not push the disc holder in manually when the power is off, as this may result in malfunction and damages the  
player.  
3. Selecting Tracks  
zꢀ Press the SKIP button once to move to next higher or lower track.  
zꢀ Hold the SKIP button to change tracks continuously at a higher speed.  
zꢀ When a new track is selected during playback, playback begins as soon as the skip search operation is completed.  
zꢀ If the skip  
button is pressed while at the last track, the first track is selected. In the same way, if the skip  
button is pressed while at the first track, the last track is selected.  
4. Starting Playback  
zꢀ Press the PLAY/PAUSE button during the pause or cue condition to start playback, the PLAY indicator lights.  
zꢀ The point at which playback starts is automatically stored in the memory as the cue point. The pickup then returns  
to the cue point when the CUE button is pressed. (Back Cue)  
Figure 4-1  
5. Stopping Playback  
There are two ways to stop playback.  
1. Press the PLAY/PAUSE button during playback to pause at that point.  
2. Press the CUE button during playback to return to the cue point and enter pause condition.(Back Cue)  
CUE  
Figure 5  
7
 
OPERATIONS  
6. Pausing  
˙Press the PLAY/PAUSE button to switch the play and pause.  
˙The play indicator flashes when the pause mode is set.  
˙Figure 6 show the relationship between the play and pause.  
2
4
6
3
7
1
5
Figure 6  
nThe player has completed the cue or pause operation  
and is waiting for the play start command.  
oWhen the PLAY/PAUSE button is pressed and enter  
play mode.  
is pressed again  
rPausing.  
sPlayback resumes when the PLAY/PAUSE button is  
pressed again.  
pPlaying.  
tPlaying.  
qThe pause mode is set when the PLAY/PAUSE button  
7. Cueing  
˙ "Cueing" is the action of preparing for playback.  
˙ Press CUE button, the player will enter cue mode, the playback returns to cue point and enter pause condition,  
the cue indicator light up and play indicator flashes. When PLAY/PAUSE button is pressed, play starts from the  
cue point.  
˙ When the track search operation is completed after pressing the SKIP buttons, the player automatically finds the  
position at which the sound starts and cues there(Auto Cue).  
˙ If the CUE button is pressed after the search operation or the scanning operation, the playback returns to cue  
point and enter pause condition.  
˙ Figure 7-1 shows the relationship between the play and back cue operations.  
2
8
2
4
6
8
3
3
7
1
1
5
9
9
Figure 7-1  
nThe player has completed the cue or pause operation  
and is waiting for the play start command.  
oWhen the PLAY/PAUSE button is pressed, playback  
starts and the cue point is stored in the memory.  
pPlaying.  
is pressed again.  
rPausing.  
sWhen the PLAY/PAUSE button is pressed again;  
tPlaying.  
uPress the CUE button.  
qThe pause mode is set when the PLAY/PAUSE button  
Cue point setting:  
vThe pickup returns to the cue point.(Back Cue)  
When play starts from pause by pressing IN button or Scanning or Frame Search; also skip to a new track by using  
skip button, the begin play point will be set to the new cue point.  
When a new cue point is set, the cue indicator lights by flash for about 1 second.  
NOTE: Daring cue mode, if the CUE button is pressed and hold, playback will start from the cue point, when the  
button is released, the player will return to the cue mode automatically, it allows you to check the cue point.  
8. Frame search  
zꢀ Frame search is a function for monitoring the sound at a certain section of the disc and manually changing the  
position. Searching is used to set play start points with precision.  
zꢀ Turn the JOG dial while in pause or cue mode to begin searching. The sound for one revolution of the disc is output  
repeatedly. The point at which the sound starts is indicated on the LCD.  
zꢀ When the JOG dial is turned, the point from which the sound is output moves a number of frames corresponding to  
the number of the clicks, and the time display on the LCD also changes.  
zꢀ The search point moves in the forward direction when the JOG dial is turned clockwise, in the reverse direction  
when the JOG dial is turned counterclockwise.  
9. Scanning (Fast forward/Fast backward)  
zꢀ Scanning is a function for moving quickly forward or backward when the SHUTTLE is rotated.  
zꢀ This unit supports 4 different speeds according to the rotating angle of the SHUTTLE.  
zꢀ Turn the shuttle dial to begin scanning. The disc moves rapidly forward or backward and the sound is output. The  
current scan point is indicated on the LCD.  
zꢀ Turn the shuttle dial clockwise to scan in the forward direction, counterclockwise to scan in the reverse direction.  
8
 
OPERATIONS  
10. Time display  
Press TIME button to select time display mode:  
TIME  
TIME  
TIME  
11. Matching the Beats Per Minute (BPM)  
There are two tools available for matching the BPM of the two CDs:  
c Use the pitch slider to adjust the BPM satirically.  
d Turn the JOG dial to change the BPM temporarily.  
1) Pitch Slider  
n To adjust the BPM by sliding the pitch slider up or down, press the PITCH button to turn on the PITCH adjustment  
function before using.  
o Slide the pitch slider up to decrease BPM, or down to increase BPM.  
2) Turn the JOG dial  
Turn the jog dial clockwise during play to increase the BMP in the forward direction, counterclockwise to decrease  
the BMP in the reverse direction. The faster you turn the wheel, the more the BMP changes. The BMP changes with  
a range of +/-16%.  
When you release jog wheel, the CD will return to the tempo indicated by the pitch slider.  
CD1  
Bass beat  
bass beat  
CD2  
bass beat  
Bass beat  
12. Program play  
n Press the PROGRAM button, the player will enter the program mode and the CD will stop rotating.  
o Select the desired track by pressing the SKIP button, then press the PROGRAM button again. The selected  
track will be added to the program sequence.  
p Repeat step 2 operation. A maximum of 20 tracks can be programmed at one time.  
q Press the PLAY/PAUSE button to start the program play from the first selection.  
r Press the program button again during program play to stop play.  
s Press and hold the program button more than 2 seconds to cancel the program mode and erase all the current  
program contents.  
13. Loop Play  
nꢀ Press the IN button to set the loop start point A, the LOOP indicator will flashes on the LCD.  
oꢀ Press the OUT button to set the loop end point B, after the B point is set, the playback will enter the loop play from  
A to B repeatedly.  
pꢀ Press the RELOOP button, the loop play function is canceled, the LOOP indicator goes out.  
14. Fader start  
You have the possibility to start the respective CD-player directly from the mixer. Make sure that the Control socket is  
connected with the respective socket on the mixer. Additionally, the Audio out socket have to be connected with the  
Line-input sockets of your mixer. Please note that the Fader start function only works with the appropriate mixers.  
Insert the CD and select the desired track. Start playback from your mixer.  
9
 
OPERATIONS  
15. Relay-Play  
In the Relay-operation, the device automatically switches to the other player after the current track is played.  
In this way, you have the possibility to automate the play features between the two CDs. As soon as the current track  
of CD1 is finished, the player automatically starts CD2. The first CD-player goes into Pause-mode. You can enter a  
new CD or memorize a Cue-point at the respective player in the Pause-Mode.  
To initiate single relay play:  
Press the SGL (Single-button); The display shows “SINGLE” on both CD-players. Then press both PROG. & SGL  
buttons simultaneously until the track indicator blinks (on both LCDs). Start playback of CD1. In the Single-mode, the  
device automatically starts with the playback of the other CD-player of the other CD-player at the end of the track.  
This can be changed to continuous by pressing the SGL (single) button once. In continuous mode the entire CD has  
to play before the second player automatically starts.  
***Note*** During the Relay-operation, the Faderstart function is disabled. CAUTION: The Relay-operation does not  
work properly if the two CD-players are connected to different power amplifiers.  
BEFORE SWITCHING OFF THE POWER  
When you have finished using the CD player, before switching off the power, be sure that the disc holder had been closed  
with the OPEN/CLOSE button.  
CAUTION:  
Do not forcibly close the disc holder when the power is off.  
POWER OFF  
POWER OFF  
8
Do not switch off the power when the disc holder is open.  
Switch off the power after the disc holder has been  
closed with the OPEN/CLOSE button.  
COMPACT DISCS  
1. Precautions on handling compact discs  
yꢀ Do not allow fingerprints, oil or dust to get on the  
surface of the disc.  
If the disc is dirty, wipe it off with a soft dry cloth.  
yꢀ Do not use benzene, thinner, water, record spray,  
electrostatic-proof chemicals, or silicone-treated  
cloths to clean discs.  
yꢀ Condensation will form if a disc is brought into a  
warm area from a colder one, such as outdoors in  
winter. Do not attempt to dry the disc with a hair dryer,  
etc.  
2. Precaution on storage  
yꢀ After playing a disc, always unload it from the  
player.  
yꢀ Always handle discs carefully to prevent damaging  
the surface; in particular when removing a disc from  
its case or returning it.  
yꢀ Do not bend the disc.  
yꢀ Do not apply heat.  
yꢀ Always store the disc in the jewel case protect from  
dirt or damage.  
yꢀ Do not place discs in the following areas:  
cꢀ Areas exposed to directs sunlight for a considerable  
time.  
yꢀ Do not enlarge the hole in the center of the disc.  
yꢀ Do not write on the label (printed side) with a hard-  
tipped implement such as a pencil or ball point pen.  
dꢀ Areas subject to accumulation of dust or high  
humidity.  
eꢀ Areas affected by heat from indoor heaters, etc.  
10  
 
SPECIFICATIONS  
GENERAL  
Dimensions:  
Main unit:  
482(W) x 88.8(H) x 251(D) mm  
19”(W) x 3 1/2”(H) x 9 4/5”(D)  
482(W) x 88.8(H) x 60(D) mm  
19”(W) x 3 1/2”(H) x 2 1/3(D)  
5 kgs / 11 lbs  
Control unit:  
Weight:  
Player unit:  
Control unit:  
Dual Voltage:  
2 kgs / 4.4 lbs  
Power supply:  
AC 115/230V, 50/60Hz  
Single Voltage:  
AC 100V, 50Hz (For Japan)  
AC 110V, 60Hz (For Taiwan)  
AC 120V, 60Hz (For U.S.A.,Canada)  
AC 127V, 60Hz (For Mexico)  
AC 220V, 50Hz (For United Arab Emirates,Chile,Aegentina)  
AC 220V, 60Hz (For Philippines)  
AC 230V, 50Hz (For Europe,U.K.,New Zealand,South Africa,Singapore,Israel)  
AC 240V, 50Hz (For Australia)  
25W  
Power consumption:  
11  
 
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement  
WARRANTY  
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S.,  
will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the  
replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year (three (3) years  
for C.D. players) following the date of original purchase. Exceptions to this warranty are as noted below:  
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days  
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and  
Switches - 10,000.  
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made  
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.  
RETURNS  
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring  
warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from  
whom the merchandise was purchased and in the same country where the merchandise was purchased. For purposes of  
purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the  
authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the  
country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized  
dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth  
above will void this warranty.  
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and  
follow such authorized Stanton dealer’s return policy.  
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application  
made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any  
rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your  
purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including  
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the  
extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of  
merchantability or fitness for a particular purpose.  
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation  
from state to state and country to country.  
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please  
include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.  
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.  
 
c u t a l o n g d o t t e d l i n e  
 
PLACE  
STAMP  
HERE  
Stanton Magnetics, Inc.  
3000 SW 42nd Street  
Hollywood, FL 33312  
U.S.A.  
 

Smooth Fitness Treadmill 625E User Manual
Sonance Speaker System Outdoor Speakers User Manual
Sony Car Stereo System NWZ A815 A816 A818 User Manual
Sony Headphones DREX12IPBLU User Manual
Sony Microcassette Recorder M 657V User Manual
Sony Microphone UWP C1 UWP C2 UWP C3 User Manual
SOYO Computer Hardware FC PGA Socket 370 Processor supported 815E AGP PCI CNR 66 100 133 MHz Front Side Bus supported ATX Form Factor User Manual
Speco Technologies Security Camera VL 183 User Manual
Stiga Trimmer VB 40 User Manual
Sunbeam Cookware FP4500 User Manual