Snapper Snow Blower 1687099 User Manual

Clean-Out Tool Kit  
Installation  
Part No. 1687099  
319 / 520 / 551 Single Stage, 5-13 HP  
Instructions  
Intermediate or Large Frame Snowthrowers  
3
Kit Contents:  
Ref. Part No. Qty. Description  
1
2
3
4
5
6
7
8
9
1733209  
1726727  
1726728  
1726995  
1678392  
1960727  
1960589  
1933896  
1960729  
1
1
1
1
1
1
1
1
1
1
1
1
CLEAN-OUT TOOL  
BRACKET, Lower  
CLIP  
5
4
11  
SPACER, 1-1/4” Long  
SPACER, 11/32” Long  
SCREW, Slotted, 10-24 x 2-1/2  
SCREW, Phillips Head, 10-24 x 3/4  
NUT, Nylock, 10-24  
CAPSCREW, 5/16-18 x 1  
CAPSCREW, 5/16-18 x 2  
DECAL, Danger  
1
10  
7
6
9
10 1960730  
11 7071880  
12 1931338  
8
12  
Carriage Bolt, 5/16-18 x 1-3/4  
2
Figure 1. Contents  
CLEARING A CLOGGED DISCHARGE  
CHUTE  
Hand contact with the rotating impeller inside the dis-  
charge chute is the most common cause of injury associ-  
ated with snowthrowers. Never use your hand to clean  
out the discharge chute.  
This kit is to install a clean-out tool on a variety of  
snowthrowers.  
WARNING  
Before beginning any service work turn off  
ignition, and disconnect the spark plug wire.  
To clear the chute:  
1. SHUT OFF THE ENGINE.  
2. Wait 10 seconds to be sure the impeller blades have  
stopped rotating.  
GENERAL OPERATION  
After installation of the clean-out tool kit, make sure  
clean-out tool is attached to handle on machine. Do not  
operate the machine without the clean-out tool properly  
stored on the handle.  
3. Always use a clean out tool, not your hands.  
DANGER  
Do not clean out discharge chute with hands.  
Contact with moving parts inside chute will  
cause serious injury. Use clean out tool provided  
with machine. Use the following procedure to  
remove objects or clear the chute:  
Upon completion of installation of clean-out tool, keep  
these instructions and warnings with the Operator’s  
Manual.  
Note: For proper use of clean-out tool it may be neces-  
sary on some models to remove the wire guard from the  
chute.  
1. Stop the engine. Remove the key  
2. Wait 10 seconds to be sure the auger/impeller  
blades have stopped rotating.  
3. Always use the clean-out tool. DO NOT use your  
hands.  
1
 
Clean-Out Tool Kit  
Installation Instructions  
(TUBE HANDLE MODELS)  
1. Remove existing hardware (A, Figure 5) from upper  
hole on left side handle (C) as shown. Discard cap-  
screw (D).  
C
A
2. Using square hole install lower bracket (B) into upper  
hole on left side handle (C) as shown. Secure with  
new 5/16-18 x 2 capscrew (D) and nut (A).  
Note: In some cases the upper hole in the left side han-  
dle is crimped flat. If so use 5/16-18 x 1 capscrew (D).  
D
A
3. Measure 16-3/8” from top of bracket (A, Figure 6) to  
center of handle (B). Center punch and drill a new  
13/64 hole (B) in handle (H).  
B
4. Attach clip (D) to handle (H) securing with #10-24 x  
2-1/2 screw (E), 1-1/4” spacer (C), and #10-24 lock-  
nut (F) mounting through new hole (B).  
Figure 5. Mounting Lower Bracket (Tube Handle)  
A. Existing Hardware  
B. Lower Bracket  
C. Handle, LH  
D. Capscrew  
5. Attach clean out tool (G) to handle (H) by first placing  
pointed end into bracket (A), then pushing hand grip  
into clip (D).  
6. Read and follow warnings when using the clean-out  
tool.  
F
B
C
D
E
16-3/8”  
H
G
A
Figure 6. Mounting Clean-Out Tool (Tube Handle)  
A. Bracket  
F. Locknut, #10-24  
G. Clean-Out Tool  
H. Handle, LH  
B. New Hole, 13/64”  
C. Spacer, 1-1/4”  
D. Clip  
E. Screw, Slotted, #10-24 x 2-1/2  
3
 
Installation Instructions  
Clean-Out Tool Kit  
D
B
F
A
B
E
C
C
D
E
H
Figure 7. Mounting Lower Bracket (520)  
15-3/8”  
A. Wing Lock Knob  
B. Lower Bracket  
C. Screw, Curved Head  
D. Handle, LH  
E. Carriage Bolt,  
5/16-18 x 1-3/4  
G
(520 MODELS)  
1. Remove wing lock knob (A, Figure 7) and carriage  
bolt (E) or screw (C) from hole on left side handle (D)  
as shown. Discard screw (C) if it was used originally.  
A
2. Using square hole install lower bracket (B) into hole  
on left side handle (D) as shown. Secure with existing  
or new 5/16-18 x 1-3/4 carriage bolt (E) and wing lock  
knob.  
Figure 8. Mounting Clean-Out Tool (520)  
A. Bracket  
F. Locknut, #10-24  
G. Clean-Out Tool  
H. Handle, LH  
3. Measure 15-3/8” from top of bracket (A, Figure 8) to  
center of handle (B). Center punch and drill a new  
13/64 hole (B) in handle (H).  
B. New Hole, 13/64”  
C. Spacer, 1-1/4”  
D. Clip  
E. Screw, Slotted, #10-24 x 2-1/2  
4. Attach clip (D) to handle (H) securing with #10-24 x  
2-1/2 screw, 1-1/4” spacer (C), and #10-24 locknut  
(F) mounting through new hole (B).  
B
5. Attach clean out tool (G) to handle (H) by first placing  
pointed end into bracket (A), then pushing hand grip  
into clip (D).  
A
B
C
C
6. Read and follow warnings when using the clean-out  
tool.  
C
(319 MODELS)  
B
Mount to right hand side handle of unit following the  
same instructions for the 520 models. Rotate position of  
new clean-out hole (B, Figure 9) approximately 30  
degrees from existing bail hole (C) to avoid interference  
of bail operation.  
A
Top View  
Cross Section View  
Figure 9. Hole Location 319 Models  
A. Handle  
C. Existing Bail Hole  
B. New Clean-Out Tool Hole  
Form No. 1727771-02  
Rev. 01/2007  
TP 200-4147-02-SK-SN  
MANUFACTURING, INC.  
Briggs & Stratton Yard Power Products Group  
Copyright © 2007 Briggs & Stratton Corporation  
Milwaukee, WI USA. All Rights Reserved  
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997 USA  
4
 

Shark Sewing Machine 384 User Manual
Sharp All in One Printer AM 900 User Manual
Shop Vac Vacuum Cleaner 200E+150 User Manual
Silva GPS Receiver DGPS 200 User Manual
Sony Ericsson Network Card TT4031 SE GM29 User Manual
Sony TV Video Accessories TDG500P User Manual
Sony VCR SRW 5500 User Manual
Speco Technologies Security Camera VL 6444DC User Manual
StreamLight Personal Computer CPMC 1553R User Manual
Sunbeam DJ Equipment MX8500 User Manual