SIIG TV Mount 04 0676A User Manual

Universal Tilting TV Mount - 23" to 42"  
Installation Instructions  
Tilting Flat-Panel TV Wall Mount  
Material: 2.0mm Cold Rolled Steel Plate  
TV Size: 23" - 42"  
Tilt: 0 / +15 degrees  
Maximum load capacity: 99lbs / 45kgs  
Wall distance: 3.1" / 80mm  
Bubble level included  
Universal Mounting Pattern  
IMPORTANT: If you don't understand the installation instructions, please  
consult an installation specialist  
04-0676A  
1
 
Note:  
1. Please ensure that the bubble level (G2) is properly attached to the  
wall plate prior to mounting.  
2. Please check the two rails before installing, if without the  
knob, please install the knob.  
Step 1: Wall plate installation  
A) Wood Stud Installation  
NOTE: For secure wood stud mounting, the wall plate must be mounted to two studs at least  
16" apart.  
1
Use a high-quality electronic stud finder (commercially available)  
to locate two adjacent studs and mark their locations with a pencil  
(1-a).  
2
Attach the bubble level (G2) to the wall plate and with the help of  
an assistant ensure the wall plate is level, position the wall plate  
against the wall in the desired mounting location.  
3
Mark the right (upper and lower) and the left (upper and lower) positions of the small horizontal slots that are in  
alignment with the studs. You should mark four positions total.  
4
5
Pre-drill a 1/8" hole to a depth of approximately 2" in the wood stud at each marked location.  
Position the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble  
level to verify that the wall plate is level.  
6
7
For each location, insert bolt (E) and washer (G1) into the wall. Do not tighten until all bolts are in place.  
Tighten each bolt with a 7/16" socket or open ended wrench by turning clockwise until tight.  
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive  
torque.  
Do not release the wall plate until it is properly mounted and secured to the wall.  
CAUTION:  
3
 
B) Concrete/Brick Installation  
NOTE: The concrete anchors must be used for concrete installation.  
1
Attach the bubble level (G2) to the wall plate, with the help of an assistant place the wall plate into position  
against the wall, using the bubble level to keep it level.  
2
3
4
5
Mark four holes to be used for securing the mount and place the wall plate aside.  
Drill holes using an electric drill and 5/16" masonry bit to a depth of approximately 2".  
Insert a concrete anchor (F) into to each hole. If necessary, a hammer can be used to lightly tap each anchor into  
Once all of the anchors are in place, move the wall plate back into position. Check the bubble level to verify that  
the wall plate is level.  
6
7
Insert bolt (E) and washer (G1) into each concrete anchor in the wall. Do not tighten until all bolts are in place.  
Tighten each bolt with a 7/16" socket or open ended wrench by turning clockwise until tight.  
Step 2 Display Bracket Installation  
1
To ensure optimal installation, this kit includes various screws of  
different diameters and lengths.  
2
Place your TV screen down on a soft, flat surface, and locate the  
threaded mounting points that are located on the back of the  
display.  
3
4
Determine which screw (A1/A2/B1/B2/C1/C2) is the correct length  
by carefully inserting a straw, or toothpick, and mark how deep  
the mounting point is.  
According to the size of the mounting point, choose the  
corresponding screw and hole on rectangle washer (D), then  
thread them in line as shown.  
5
If your display has a curved back or a recessed thread mounting  
point, place the spacer (H) between the mounting bracket and  
display and then choose screw (A2/B2/C2) to match.  
4
 
Step 3 Final Installation & Adjustment  
1
2
Hook the TV rails over the top of wall plate.  
The TV rail can be tilted down up to 15 degrees. To make this adjustment, first loosen the knob and pull or push  
the rail until it is in the desired position. Once the desired level of tilt is achieved, re-tighten the mount by turning  
the tension knobs.  
3
On the TV rail equipped with screw, rotate the long screw at the bottom of the display rail to tighten it and secure  
the mount.  
Maintenance  
Check the mounting screws every two months for tightness.  
5
 
Blank Page  
6
 
Technical Support and Warranty  
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online  
support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analysts will promptly respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the original purchaser and guarantees the  
product to be free of any defects in materials or workmanship for five (5) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the  
product if defective in materials or workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or  
replaced.  
Step 1: Submit your RMA request.  
product is determined to be defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original package  
must be included.  
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton.  
• You are responsible for the cost of shipping the product to SIIG. Ship the product to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #: ________________  
• SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no  
cost to the customer.  
7
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra  
ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/Notebook  
systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity  
solutions to our extensive portfolio. All centered around the distribution and switching of A/V signals over CAT5/6,  
these products include matrix switches, distribution amplifiers, extenders, converters, splitters, cabling, and more.  
SIIG is the premier one-stop source of upgrades and is committed to providing high quality products while keeping  
economical and competitive prices. High-quality control standards are evident by one of the lowest defective  
return rates in the industry. Our products offer comprehensive user manuals, user-friendly features, and most  
products are backed by a lifetime warranty.  
SIIG products can be found in many computer retail stores, mail order catalogs, and e-commerce sites in the  
Americas, as well as through major distributors, system integrators, and VARs.  
PRODUCT NAME  
Universal Tilting TV Mount - 23" to 42"  
Universal Tilting TV Mount - 23" to 42" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG,  
Inc. Other names used in this publication are for identification only and may be trademarks of their respective owners.  
January, 2011  
Copyright © 2011 by SIIG, Inc. All rights reserved.  
8
 

Sennheiser Microphone E 815 S User Manual
Sharp Camcorder VL Z7U User Manual
Sharp Car Satellite TV System LC 32L400X User Manual
Sharp Microwave Oven R395Y O M User Manual
Sony Ericsson Bluetooth Headset VH700 User Manual
Soundstream Technologies Speaker PXW 10 User Manual
Stinger Automobile Accessories SGN13 User Manual
Sunbeam Fan SEH8001 User Manual
Sungale Digital Photo Frame ID350AT User Manual
Sylvania Indoor Furnishings EN ECU G4 P3D User Manual