Sanyo Camera Lens LNS W32 User Guide

LCD PROJECTOR LENS  
MODEL LNS-W32  
LENS REPLACEMENT PROCEDURE  
NOTE; Lens installation is different in cabinet design and lens attachment method  
(Type A, B and C). Before installation the lens, check cabinet design and  
proper installation should be made.  
NOTES ON LENS REPLACEMENT  
The ZOOM, FOCUS and LENS SHIFT adjustment on the Top Control or the  
Remote Control cannot be operated with this Lens.  
Lens replacement should be performed by the qualified service personnel.  
It should be followed by this procedure precisely.  
Before attempt to replace the lens, confirm the model number (both the LCD  
projector and the lens) and use the proper lens.  
The lens cover is on the lens for protection. Be sure to remove the lens cover  
before installation.  
When installing or removing the lens, be careful not to stain, scratch or  
damage the lens.  
PARTS LIST  
Following parts are contained in the packing.  
LENS  
1 piece  
LIGHT-BLOCK SHEET BASE  
DRIVER (3 mm, Green)  
DRIVER (4 mm, Yellow)  
LIGHT-BLOCK SHEET  
1 piece (Part No. 610 310 8001)  
1 piece (Part No. 610 287 7328)  
1 piece (Part No. 610 275 6029)  
1 piece Type PC1 (Part No. 610 310 7967)  
1 piece Type PD1 (Part No. 610 294 3047)  
2 pieces (Spare parts)  
SCREW  
Following checks and confirmations should be taken for safety.  
Check the following things by the time of the cabinet assembly after the lens  
replacement.  
1. Check the lens is securely fixed.  
2. Check no parts is missing, or no mounting part is loose.  
Some parts are not used for installation or replacement. Keep these parts and  
drivers included in the lens for later use.  
1AA6P1P3217A- (ICZAA-A)  
 
3
REMOVE THE LENS (See Figure-5 and 6)  
1. Disconnect the Lens Shift connector "K16L" from  
the circuit board on cabinet left side.  
2. Disconnect the Zoom and Focus connector "K16J"  
from the circuit board.  
Remove the lens motor lead from lead holder.  
Remove screws-C (4 screws) which fastens the  
lens and remove the lens. Use the driver (3 mm,  
Green) included with the lens to remove the  
screws.  
3.  
Be careful not to drop the lens when removing the  
screws.  
LENS  
MOTOR  
LEAD  
HOLDER  
SCREW "C"  
CIRCUIT BOARD ON  
CABINET LEFT SIDE  
LENS MOTOR LEAD  
CONNECTOR "K16J"  
CONNECTOR "K16L"  
Fig-5  
-3-  
 
4
MOUNT THE LENS (See Figure-5 and 6)  
DRIVER  
IN THE LENS  
1.  
Remove protective caps (front and back) on the  
lens.  
Mount the lens on lens mounting bracket with 4  
screws.  
2.  
Use the driver (4 mm, Yellow) included with the  
lens to fasten the screws.  
LENS MOUNTING  
BRACKET  
CONFIRM THE FOCUS  
Fig-6  
Project picture on screen and confirm the focus. If  
proper focus is not observed at screen, adjust focus  
following Focus Adjustment on this page.  
5 MOUNT THE LIGHT-BLOCK SHEET AND  
FRONT PANEL (See Figure-7)  
LIGHT-BLOCK SHEET  
Type PD1  
(Part No. 610 294 3047)  
1.  
2.  
3.  
Mount the light-block sheet to the lens as shown in  
the Figure-7. Use the sheet included with the lens.  
Make sure the part no. and mark (TOP and BACK)  
on Light-Block Sheet and set them properly.  
Mount the Front Panel (Separately ordered) with  
the screws.  
Fig-7  
FRONT PANEL  
(OPTIONAL PART)  
Light block sheet base is not used.  
FOCUS ADJUSTMENT  
Set up the projector and project image on the screen.  
1. Loosen the Focus Lock Screw on the lens.  
2. Rotate the lens to obtain proper focus on center  
area of the screen.  
3. Tighten the Focus Lock Screw.  
When proper focus is not observed at outer area of  
the screen, proceed to following adjustments.  
4. Loosen the Focus Lock Ring of the lens. (Turn the  
Lock Ring to counter-clockwise.)  
5. Rotate the lens to obtain proper focus on outer  
area of the screen.  
6. Lock the Focus Lock Ring securely. (Turn the Lock  
Ring to clockwise.)  
Focus Lock Ring  
If proper focus is not observed entire screen, repeat  
above adjustment 1~ 6.  
Focus Lock Screw  
-4-  
 
LENS REPLACEMENT PROCEDURE (FOR "B" TYPE)  
Perform the steps  
to  
for lens replacement.  
5
1
SCREW "A"  
First set the lens at the fully lower position with  
lens shift adjustment.  
FRONT CABINET  
REMOVE THE LENS COVER AND  
1
FRONT CABINET  
1. Turn the lens cover to counter-clockwise and  
pull it toward front and remove the Lens  
Cover.  
Fig-1-1  
LENS COVER  
Remove 2 Screws-A.  
2.  
3.  
Remove the front cabinet  
SCREW "A"  
See Figure-1-1 and 2.  
FRONT CABINET  
1. Remove 3 Screws-A.  
Remove the front cabinet  
2.  
See Figure-1-2 and 2.  
Fig-1-2  
LENS COVER  
SCREW "A"  
1. Pull Lens Cover toward front and remove it.  
2. Remove 2 Screws-A.  
Remove the front cabinet  
3.  
See Figure-1-3 and 2.  
Fig-1-3  
FRONT CABINET  
LIGHT-BLOCK  
SHEET BASE  
REMOVE THE LIGHT-BLOCK SHEET BASE  
AND LIGHT-BLOCK SHEET (See Figure-2)  
2
LIGHT-BLOCK  
SHEET  
1.  
Slide the light-block sheet base upward  
and remove it.  
LENS COVER  
2. Remove the light-block sheet from lens.  
FRONT  
CABINET  
Fig-2  
-5-  
 
3
REMOVE THE LENS (See Figure-3 and 4)  
SCREW "B"  
1. Remove the lens motor connector from terminal.  
2.  
Loosen the screws-B (2 screws) which fastens  
the lens. {Use the driver (4 mm, Yellow) included  
with the lens to loosen the screws.}  
3. Slide the lens lock latches to "UNLOCK" position  
and remove the lens.  
LENS LOCK  
LATCHES  
Be careful not to drop the lens when removing the  
screws. After using, save the driver for latter use.  
Fig-3  
CONNECTOR  
TERMINAL  
LENS LOCK LATCHES  
LOCK  
POSITION  
UNLOCK  
POSITION  
Fig-4  
4
MOUNT THE LENS (See Figure-5)  
LENS MOUNTING  
BRACKET  
1.  
Remove protective caps (front and back) on the  
lens.  
Mount the lens on lens mounting bracket with  
Upper 2 screws.  
2.  
DRIVER  
IN THE LENS  
Use the driver (4 mm, Yellow) included with the  
lens to fasten the screws.  
Remove the lower 2 screws on the Lens. (Lower 2  
screws are not used.)  
Slide the lens lock latches to "LOCK" position and  
lock the lens. (See Figure-4)  
3.  
LOWER SCREWS  
Fig-5  
CONFIRM THE FOCUS  
Project picture on screen and confirm the focus. If  
proper focus is not observed at screen, adjust focus  
following Focus Adjustment on next page.  
-6-  
 
LIGHT-BLOCK  
SHEET  
MOUNT THE LIGHT-BLOCK SHEET AND  
LIGHT-BLOCK SHEET BASE (See Figure-6)  
5
Type PC1  
(Part No. 610 310 7967)  
LIGHT-BLOCK  
SHEET BASE  
Mount the light-block sheet on the lens. (In the same  
position as the removed sheet has been placed). Use  
the sheet included with the lens.  
1.  
Make sure the mark (TOP and BACK) on Light-Block  
Sheet and set them properly.  
Mount the light-block sheet base included with the  
lens.  
2.  
FRONT  
CABINET  
Fig-6  
MOUNT THE FRONT CABINET AND LENS  
COVER (See Figure-7)  
6
1.  
Mount the front cabinet with 2 screws.  
Lens cover is not used.  
Fig-7  
FOCUS ADJUSTMENT  
Set up the projector and project image on the screen.  
1. Loosen the Focus Lock Screw on the lens.  
2. Rotate the lens to obtain proper focus on center  
area of the screen.  
3. Tighten the Focus Lock Screw.  
When proper focus is not observed at outer area of  
the screen, proceed to following adjustments.  
4. Loosen the Focus Lock Ring of the lens. (Turn the  
Lock Ring to counter-clockwise.)  
5. Rotate the lens to obtain proper focus on outer  
area of the screen.  
6. Lock the Focus Lock Ring securely. (Turn the Lock  
Ring to clockwise.)  
Focus Lock Ring  
If proper focus is not observed entire screen, repeat  
above adjustment 1~ 6.  
Focus Lock Screw  
-7-  
 
LENS REPLACEMENT PROCEDURE (FOR "C" TYPE)  
Perform the steps  
to  
for lens replacement.  
1
6
SCREW "A"  
First set the lens at the fully lower position with lens  
shift adjustment.  
FRONT CABINET  
REMOVE THE LENS COVER AND  
FRONT CABINET  
1
1.  
Turn the lens cover to counter-clockwise and pull it  
toward front and remove the Lens Cover.  
2. Remove 2 Screws-A.  
Remove the front cabinet  
3.  
LENS COVER  
LIGHT-BLOCK  
SHEET BASE  
REMOVE THE LIGHT-BLOCK SHEET BASE  
AND LIGHT-BLOCK SHEET  
2
LIGHT-BLOCK  
SHEET  
Slide the light-block sheet base upward and  
remove it.  
Remove the light-block sheet from lens.  
1.  
2.  
LENS COVER  
FRONT  
CABINET  
LENS LOCK  
LEVER  
Pull the Lens  
Lock Lever  
upward  
REMOVE THE LENS  
3
1.  
Grasp the Lens Lock Lever and turn it fully  
upward. Remove the Lens into the projector.  
2. Disconnect the lens motor lead connector to the  
socket on the lens attachment.  
Remove 4 Screws and remove lens attachment.  
3.  
LENS  
ATTACHMENT  
SCREW  
SOCKET  
CONNECTOR  
LENS MOTOR  
LEAD  
- 8 -  
 
MOUNT THE LENS  
4
1.  
Remove protective caps (front and back) on the optional lens.  
2.  
3.  
4.  
Mount the lens on the lens attachment with 4 Screws.  
Connect the lens motor lead connector to the socket on the lens attachment.  
Grasp the Lens Lock Lever and turn it fully upward. Install the Lens into the projector. Turn  
the Lens Lock Lever fully downward until lever is Locked (clicked position) properly.  
After installing the lens, make sure the Lens is not loose and properly installed.  
LENS  
ATTACHMENT  
LENS LOCK LEVER  
B
A
SPACER  
C
D
A~D  
Insertion position  
of the focus  
correction spacers.  
Refer to following.  
DRIVER  
IN THE LENS  
Part No. (610 275 6029)  
Push the Lens  
LENS LOCK LEVER  
Lock Lever fully  
downward until it is  
locked (clicked).  
Correcting the focus  
Screen  
D
When the lens is attached to the projector and  
images are being projected onto the screen, the  
peripheral focus may be out of focus in some  
localized areas. If this happens, insert the spacer  
in between the lens attachment and the lens to  
correct the focus.  
B
Screen  
40-inch projection  
A
C
Insert spacers in  
the location A~D  
(above figure)  
corresponding to  
the screen location  
A~D.  
Distance  
Inserting the spacers corrects the distance for best  
diagonal focus at the screen.  
The corrected distance is determined by the  
thickness of the spacers that are used. As a guide,  
the distance is adjusted by approximately 30 mm  
for each 0.1-mm thickness of the spacers.  
There are three types of spacers provided, and  
there are four of each spacer type. Use these  
spacers to correct the distance as required.  
Spacer "1"  
Color; Clear  
Thickness; 0.1 mm  
Correction distance  
30 mm/for 40-inch  
projection  
Spacer "2"  
Color; Black  
Thickness; 0.2 mm  
Correction distance  
55 mm/for 40-inch  
projection  
Correction distance  
80 mm/for 40-inch  
projection  
Spacer "1"  
Color; Cream  
Thickness; 0.3 mm  
- 9 -  
 
LIGHT-BLOCK  
SHEET  
MOUNT THE LIGHT-BLOCK SHEET AND  
LIGHT-BLOCK SHEET BASE  
5
Type PC1  
(Part No. 610 310 7967)  
LIGHT-BLOCK  
SHEET BASE  
Mount the light-block sheet on the lens. (In the same  
position as the removed sheet has been placed). Use  
the sheet included with the lens.  
1.  
Make sure the mark (TOP and BACK) on Light-Block  
Sheet and set them properly.  
Mount the light-block sheet base included with the  
lens.  
2.  
FRONT  
CABINET  
MOUNT THE FRONT CABINET AND LENS  
COVER  
6
1.  
Mount the front cabinet with 2 screws.  
Lens cover is not used.  
FOCUS ADJUSTMENT  
Set up the projector and project image on the screen.  
1. Loosen the Focus Lock Screw on the lens.  
2. Rotate the lens to obtain proper focus on center  
area of the screen.  
3. Tighten the Focus Lock Screw.  
When proper focus is not observed at outer area of  
the screen, proceed to following adjustments.  
4. Loosen the Focus Lock Ring of the lens. (Turn the  
Lock Ring to counter-clockwise.)  
5. Rotate the lens to obtain proper focus on outer  
area of the screen.  
Focus Lock Ring  
6. Lock the Focus Lock Ring securely. (Turn the Lock  
Ring to clockwise.)  
If proper focus is not observed entire screen, repeat  
above adjustment 1~ 6.  
Focus Lock Screw  
- 10 -  
 

Ratoc Systems Network Card RHD DTxx User Guide
Remington Chainsaw BPS188A User Guide
Ricoh All in One Printer 1075 User Guide
Salton Beverage Dispenser WC22 User Guide
Samsung Clothes Dryer DV317AGS User Guide
Samsung Clothes Dryer DV338AGW User Guide
Samsung Digital Camera AD68 04778A User Guide
Samsung Satellite Radio 20 006A User Guide
Sanyo Battery Charger UPF323456L User Guide
Sears Automobile Parts 143994006 User Guide