Radio Shack Door 63 1123 User Guide

5KPING"$GNN"9KTGNGUU"&QQT"%JKOG  
63-1123  
OWNER’S MANUAL — Please read before using this equipment.  
"+/2146#06"  
#
#
If an icon appears at the end of a paragraph,  
go to the box on that page with the  
Transmitter  
Receiver  
corresponding icon for pertinent information.  
Indicator — Lights when  
BELL is pressed.  
— Warning  
° — Hint  
± — Note  
Rý  
. — Caution  
— Important  
#
Slide ON/OFF to ON  
BELL — Press BELL  
so that when BELL  
to hear the door  
is pressed on the  
chime.  
transmitter, a door  
chime sounds.  
Thank you for purchasing the RadioShack  
Single Bell Wireless Door Chime. It works as  
a doorbell, remote pager, or alert. You can  
add an optional external sensor to have a  
chime that alerts you when someone walks  
into a room. The door chime’s three-position  
channel switch prevents other transmitters  
or radio devices from sounding the chime.  
/1706+0)"6*'"  
4'%'+8'4  
10"#"(.#6"574(#%'  
4. Drive a screw through the holder into  
each hole.  
Pull out the wire stand on the back of the  
receiver and set it on a table or other flat  
surface.  
5. The transmitter can be slid in and out of  
the holder. To lock the transmitter, fix it  
with a size M2.6 screw at the bottom of  
the holder.  
10"#"9#..  
1. Drill one 3/16-inch diameter hole and  
insert one of the supplied anchors.  
+056#..+0)"  
2. Drive the supplied M3.5 screw into the  
hole until the screw's head extends  
about 1/8 inch from the wall.  
$#66'4+'5"#0&"  
5'.'%6+0)"%*#00'.5  
."%#76+10".  
• Use only fresh batteries of the required size  
and type. Always remove old or weak  
batteries. They can leak chemicals that  
destroy electronic circuits  
3. Align the keyhole slot on the bottom of  
the receiver with the screw in the wall,  
then slide it down to secure it.  
The door chime requires three AAA batteries  
in the transmitter and three C batteries in the  
receiver. For best performance and longest  
life, we recommend RadioShack alkaline  
batteries. .  
• Do not mix old and new batteries, different  
types of batteries (standard, alkaline, or  
rechargeable), or rechargeable batteries of  
different capacities.  
/1706+0)"6*'"  
64#05/+66'4"  
+0"6*'"64#05/+66'4  
1. Remove the transmitter from the holder.  
1. Slide the transmitter's battery  
compartment door in the direction of the  
arrow to remove it.  
2. Use the holder as a template to mark  
two screw holes on the wall.  
2. Use a small flat-blade screwdriver to  
slide the switch inside the battery  
compartment to the desired channel for  
the transmitter.  
3. Remove the holder from the mounting  
surface and drill two 3/16 inch diameter  
holes. Insert one of the supplied  
anchors into each hole.  
© 2002 RadioShack Corporation.  
All Rights Reserved.  
RadioShack and RadioShack.com are trademarks  
used by RadioShack Corporation.  
 

Q See Home Security System QPSCDNV User Guide
Radio Shack Video Game Controller 26 701 User Guide
RCA Flat Panel Television MAF75BKR User Guide
RCA MP3 Player TH161 Series User Guide
Roland Stereo Amplifier JC 120 User Guide
Rotel Music Mixer RSP 975 User Guide
Samsung Clothes Dryer DV400EWHDWR User Guide
Samsung Printer ML 6060N User Guide
Sears Air Compressor 919154020 User Guide
Sears Home Gym 831288140 User Guide