Radio Shack Cordless Telephone 43 3558 User Guide

Caller ID/Call Waiting ID  
43-3557/43-3558  
Ten-Number Memory Dialing — lets you store up to ten numbers in  
memory for easy dialing. (See “Memory Dialing” on page 19.)  
Ample Talk and Standby Time —  
the supplied battery (when fully  
charged) provides about 7 hours of  
talk time or 14 days of standby time.  
Headset Jack — lets you connect an  
optional headset for hands-free  
convenience. (See “Headset  
Installation” on page 32.)  
Auto Talk— lets you  
set the phone to  
answer a call by simply  
lifting the handset from  
the base.  
IMPORTANT  
!
!
If an icon appears at the end of a paragraph, go to the box on that page with the  
corresponding icon for pertinent information.  
— Warning  
— Important — Caution Ô — Note  
!
o
OWNER’S MANUAL  
Please read before using this equipment.  
© 2004 RadioShack Corporation.  
All Rights Reserved.  
RadioShack and RadioShack.com are trademarks  
used by RadioShack Corporation.  
ENERGYSTAR and the ENERGYSTAR certification mark  
are registered US marks.  
 
INTRODUCTION  
Thank you for purchasing a RadioShack 2.4  
GHz Cordless Telephone. Your phone uses  
advanced technology to give you superior  
audio quality and extended range. The  
phone’s Caller ID unit records each caller’s  
telephone number (and name, if available in  
your area) and the date and time of the call,  
as provided by your local phone company to  
Caller ID service subscribers. If you  
subscribe to Call Waiting with Caller ID, the  
phone shows you the incoming caller  
information, even when you are already  
talking on the phone.  
Cordless phones require AC power to  
operate. When the power is off, you cannot  
make or receive calls by using your phone.  
You should also have a phone that does not  
need AC power to operate (not a cordless  
phone), so you can still make and receive  
IMPORTANT  
!
!
When AC power is lost,  
the phone loses the  
digital security code  
calls if there is an AC power failure.  
connection between the  
base and the handset.  
When power is restored,  
put the handset on the  
base briefly to restore  
this connection so you  
can use the handset.  
!
Your phone operates on  
standard radio  
frequencies as allocated  
by the FCC.  
It is possible for other  
radio units operating  
nearby on similar  
frequencies to  
unintentionally intercept  
your conversation or  
cause interference. This  
possible lack of privacy  
can occur with any  
cordless phone.  
3
 
 
As an ENERGYSTAR Partner,  
RadioShack Corporation has  
determined that this product  
meets the ENERGYSTAR guidelines  
for energy efficiency.  
IMPORTANT  
INFORMATION  
This telephone has been tested and found  
to comply with all applicable UL and FCC  
standards.  
FCC STATEMENT  
Your telephone compiles with Part 68 of the  
FCC Rules.Upon request, you must provide  
the phone’s FCC registration number and  
REN to your phone company. These  
numbers are on the base unit.  
Your phone is not intended to be used with  
party-line systems. Connection to party line  
service is subject to state tariffs. Contact the  
state public utility commission, public  
service commission, or corporation  
commission for information. Ô  
We have designed your phone to conform  
to federal regulations, and you can connect  
it to most telephone lines. However, each  
phone (and each device, such as a  
telephone or answering machine) that you  
connect to the telephone line draws power  
from the telephone line. We refer to this  
power draw as the device’s ringer  
Ô NOTE Ô  
You must not connect your  
phone to:  
equivalence number, or REN on the back of  
your phone.  
If you use more than one phone or other  
device on the line, add up all of the RENs. If  
the total is more than five (three in rural  
areas), your telephones might not ring. If  
coin-operated systems  
most electronic key  
telephone systems  
4
 
   
ringer operation is impaired, remove a  
device from the line.  
In the unlikely event that your phone causes  
problems on the phone line, the phone  
company can temporarily discontinue your  
service. If this happens, the phone company  
attempts to notify you in advance. If  
advance notice is not practical, the phone  
company notifies you as soon as possible  
and advises you of your right to file a  
complaint with the FCC.  
Also, the phone company can make  
changes to its lines, equipment, operations,  
or procedures that could affect the operation  
of this phone. The telephone company  
notifies you of these changes in advance, so  
you can take the necessary steps to prevent  
interruption of your telephone service.  
This device complies with part 15 of the  
FCC rules. Operation is subject to the  
following two conditions: (1) This device  
may not cause harmful interference, and (2)  
This device must accept any interference  
received, including interference that may  
cause undesired operation. Privacy of  
communications, may not be ensured when  
using this phone.  
SURGE PROTECTION  
Your telephone has built-in protection  
circuits to reduce the risk of damage from  
surges in telephone line and power line  
current. These protection circuits meet or  
exceed the FCC requirements. However,  
lightning striking the telephone or power  
lines can damage your telephone.  
Lightning damage is not common.  
Nevertheless, if you live in an area that has  
severe electrical storms, we suggest that  
you unplug your phone when storms  
approach to reduce the possibility of  
damage.  
5
 
 
IMPORTANT SAFETY INSTRUCTIONS  
When using your telephone equipment, basic safety precautions should  
always be followed to reduce the risk of fire, electric shock and injury to  
persons, including the following:  
1. Do not use this product near water, for example, near a bathtub,  
wash bowl, kitchen sink, or laundry tub, in a wet basement or near a  
swimming pool.  
2. Avoid using a telephone (other than a cordless type) during an  
electrical storm. There may be a remote risk of electric shock from  
lightning.  
3. Do not use the telephone to report a gas leak in the vicinity of the  
leak.  
4. Use only the power cord and batteries indicated in this manual.  
Do not dispose of batteries in a fire. They may explode. Check with  
local codes for possible special disposal instructions.  
SAVE THESE INSTRUCTIONS  
6
 
 
IMPORTANT CALLER  
ID INFORMATION  
To use Caller ID and Call Waiting, you must  
be in an area where those services are  
available and you must subscribe to those  
services through your local phone company.  
Where Caller ID is offered, one or more  
options are generally available:  
• caller’s number only  
• caller’s name only  
• caller’s name and number  
If you subscribe to Call Waiting ID and  
Caller ID, the system can show you the  
incoming caller information, even when you  
are already talking on the phone.  
7
 
 
INSTALLATION  
Before using your phone, carefully peel the  
protective film off the display. The film  
protects the handset window during  
shipment and is not necessary for use.  
SELECTING A LOCATION  
You can place the phone’s base on a desk  
or table, or mount it on a standard wall plate  
or directly on a wall. Select a location that  
is:Ô  
• near an accessible AC outlet  
• near a telephone line jack  
• out of the way of normal activities  
• away from electrical machinery,  
electrical appliances, metal walls or  
filing cabinets, wireless intercoms,  
alarms, and room monitors  
• away from other cordless phones  
The base’s location affects the handset’s  
range. If you have a choice of several  
locations, try each to see which provides the  
best performance.  
Ô NOTES Ô  
If your home has  
specially wired alarm  
equipment connected to  
the telephone line, be  
sure that installing the  
system does not disable  
your alarm equipment.  
If you have questions  
about what will disable  
alarm equipment,  
Your telephone connects directly to a  
modular telephone line jack. If your  
telephone wiring does not have a modular  
jack, you can update the wiring yourself  
using jacks and adapters (available at your  
local RadioShack store), or have the  
telephone company update the wiring for  
you. You must use compatible modular  
jacks that are compliant with Part 68 of FCC  
Rules. Ô  
contact your telephone  
company or a qualified  
installer.  
The USOC number of  
the jack to be installed is  
RJ11C (or RJ11W for a  
wall plate jack).  
8
 
   
ON A DESK TOP  
1. Plug one end of  
the supplied long  
modular cord into  
the TEL LINE jack  
on the back of the  
base.  
TEL  
LINE  
DC IN 9V  
2. Insert the supplied  
AC adapter’s  
CAUTION  
You must use  
barrel plug into the  
DC IN 9V jack on  
the back of the  
base and route the  
adapter’s cord  
a Class 2  
power source  
that supplies  
!
9V DC and delivers at  
least 210 mA. Its center  
tip must be set to  
through the strain  
relief slot on the base.ꢀ  
positive and its plug  
must fit the phone’s DC  
IN 9V jack. The supplied  
adapter meets these  
specifications. Using an  
adapter that does not  
meet these  
specifications could  
damage the phone or  
the adapter.  
3. Plug the other end of the modular cord  
into a modular phone line jack.  
4. Plug the adapter into a standard AC  
outlet.  
ON A WALL PLATE OR WALL  
To mount the phone directly on a wall, you  
need two screws (not supplied) with heads  
that fit into the keyhole slots on the base.  
Drill two holes 315/16 inches apart. Thread a  
screw into each hole, letting the heads  
extend about 1/8 inch.  
1. Insert the two  
of upper tabs  
of the supplied  
bracket into  
the base’s  
upper tab  
slots. Then slide down the bracket so  
that two of the lower tabs would be  
inserted into the lower slots.  
9
 
   
2. Plug one end of the supplied modular  
cord (short for a wall plate, long for  
direct wall mounting) into the TEL LINE  
jack on the base’s back.  
3. Plug the supplied AC adapter's barrel  
plug into the DC IN 9V jack.  
4. Route the adapter  
and modular cords  
through the  
TEL LINE  
bracket’s grooves.  
5. For a wall plate,  
align the bracket’s  
keyhole slots with  
the wall plate  
DC IN 9V  
IMPORTANT  
!
!
The EPA  
studs and slide the base downward to  
secure it.  
certified  
RBRC® Battery  
Recycling Seal  
on the nickel-  
For direct wall  
mounting, align  
the bracket’s  
keyhole slots  
with the  
mounting  
screws and slide  
the base  
cadmium (Ni-Cd) battery  
indicates RadioShack is  
voluntarily participating in  
an industry program to  
collect and recycle these  
batteries at the end of their  
useful life, when taken out  
of service in the United  
States or Canada. The  
RBRC program provides a  
convenient alternative to  
placing used Ni-Cd  
batteries into the trash or  
the municipal waste  
stream, which may be  
illegal in your area. Please  
call 1-800-THE-SHACK (1-  
800-843-7422) for  
downward to secure it.  
6. Plug the adapter into a standard AC  
outlet. And plug the modular cord’s  
other end into a modular phone line  
jack.  
CONNECTING/CHARGING THE  
information on Ni-Cd  
battery recycling and  
BATTERY PACK  
The phone comes with a rechargeable  
nickel-cadmium battery pack in the handset,  
but not connected. Before using your  
phone, you must connect the battery pack.  
disposal bans/restrictions  
in your area. RadioShack’s  
involvement in this program  
is part of the company’s  
commitment to preserving  
our environment and  
Then charge it for about 15–20 hours.  
!
conserving our natural  
resources.  
10  
 
 
1. Press down and slide off the battery  
compartment cover.  
IMPORTANT  
!
!
Be sure the battery pack is  
properly connected before  
you try to charge it. The  
CHARGE/IN USE indicator  
lights when the handset is  
on the base, even if the  
battery pack is not  
2. Lift the battery pack out of the  
compartment.  
3. Plug the battery pack’s connector into  
the socket in the compartment (the  
connector fits only one way). Then  
place the battery pack in the  
compartment.  
connected.  
4. Replace the cover.  
To charge the battery pack, place the  
handset on the base. The CHARGE/IN USE  
indicator on the base lights.  
!
Recharge the battery pack when Low  
Batteryflashes on the display.Ô  
Ô NOTES Ô  
If the phone does not  
work, recharge the  
battery pack. (The  
battery power might be  
too low for the display to  
operate.)  
When you first use the phone after charging  
or recharging the battery pack, the phone  
might not work and you might hear error  
beeps. If this happens, place the handset to  
the base to change the digital security code.  
If the battery pack  
becomes weak during a  
call, the handset beeps  
and Low Battery  
flashes. When this  
happens, you cannot  
make a call on the  
Using a damp cloth, clean the charging  
contacts on the handset about once a  
month.  
phone until you recharge  
the battery pack.  
About once a month, fully discharge the  
battery pack by keeping the handset off the  
base until LowBatteryflashes.  
Otherwise, the battery pack loses its ability  
to fully recharge.  
If the battery pack is  
completely discharged  
or the base loses power  
while the handset is  
away from it, place the  
handset on the base to  
change the digital  
security code.  
11  
 
The supplied battery pack should last about  
a year. If the battery pack does not hold a  
charge for more than two hours after an  
overnight charge, replace it with a new  
3.6V, 600 mAh battery pack with a  
connector that fits the socket in the battery  
compartment. You can order a replacement  
battery pack through your local RadioShack  
store (or online at RadioShack.com). Install  
the new battery pack and charge it for about  
24 hours.  
WARNING  
o
o
Dispose of the old battery  
pack promptly and properly.  
Do not burn or bury it.  
There is a risk of explosion  
if battery is replaced by an  
incorrect type. Dispose of  
used batteries according to  
the instructions.  
If you have trouble replacing the battery  
pack, take the phone to your local  
RadioShack for assistance.  
o
12  
 
OPERATION  
MAKING AND RECEIVING  
CALLS  
Action Handset On Base Handset Off Base  
Press TALK/  
Pick up the handset  
FLASH, any  
Ô NOTE Ô  
(Auto Talk: On) Ô  
To  
answer  
a call  
number, /TONE/<  
or #/> (Auto Talk:  
On) or press TALK/  
FLASH (Auto Talk:  
Off).  
Refer to page 17 “Setting  
Menu Options” to turn On  
the Auto Talk feature if  
desired.  
or pick up the  
handset and press  
TALK/FLASH(Auto  
Talk: Off).  
1)Pick up the  
handset.  
1)Press TALK/  
FLASH.  
2)Press TALK/  
FLASH.  
2)Listen for the dial  
tone.  
3)Listen for the dial 3)Dial the number.  
tone. OR  
To  
make 4)Dial the number. Dial the number.  
a call OR  
1)Pick up the  
Then press TALK/  
FLASH.  
handset.  
2)Dial the number.  
Then press  
TALK/FLASH.  
To  
hang  
up  
Press END or return the handset to the  
base (Auto Standby).  
1)Pick up the  
handset.  
1)Press TALK/  
FLASH.  
2)Press TALK/  
FLASH.  
2)Listen for the dial  
tone.  
3)Listen for the dial 3)Press PAUSE/  
tone.  
4)Press PAUSE/  
REDIAL.  
OR  
1)Pick up the  
handset.  
REDIAL.  
OR  
Press PAUSE/  
REDIAL. Then  
press TALK/  
FLASH.  
To  
redial  
2)Press PAUSE/  
REDIAL. Then  
press TALK/  
FLASH.  
13  
 
   
ADJUSTING THE HANDSET  
RINGER AND EARPIECE  
VOLUME  
Handset Ringer Tone and Volume  
Press the volume up key or volume down  
key (labeled as,  
VOL or  
VOL keys) in  
standby mode to select one of five ringer  
tones and volume combinations. Ring  
Type A High, Ring Type A Low, Ring  
Type B High, Ring Type B Low, or  
Ringer Off.  
Earpiece Volume  
Press the volume up key or volume down  
key (labeled as,  
VOL or  
VOL keys)  
Ô NOTE Ô  
When you press volume up  
key ( VOL) in Maximum  
mode or volume down key  
during a call to change the earpiece volume  
of the handset. This setting will remain in  
effect after the telephone call has ended. Ô  
(
VOL) in Low mode, an  
Temporarily Mute Ringer  
If the handset is off the base, simply press  
END to temporarily mute the incoming ring.  
The ringer will sound with the next incoming  
call.  
error tone sounds.  
REDIAL  
PAUSE/REDIAL redials the last number  
dialed. The redialed number can be up to 32  
digits long.  
14  
 
         
TONE DIALING SWITCH-OVER  
Some telephone companies use equipment  
that requires pulse dialing (sometimes  
referred to as rotary dialing).  
If you need to enter tone dialing digits, you  
can switch-over to tone dialing during the  
call. For example, entering your bank  
account number after you have called your  
bank. Ô  
Ô NOTES Ô  
The tone feature only  
applies when the dial  
mode is set to pulse.  
Initially make your call with the pulse dialing  
This special number can  
be stored in a memory  
location. This is referred  
to as Chain Dialing (See  
“Chain Dialing” on  
mode. Once your call connects, press  
/
TONE/<. Enter the desired number. These  
digits will be sent as tone dialing. Once the  
call ends, the tone mode is canceled and  
pulse dialing mode resumes.  
page 23.)  
TRAVELING OUT-OF-RANGE  
During a call, as you begin to move your  
handset too far from your base unit, noise  
increases. If you pass the range limits of the  
base unit, your call will terminate within one  
minute.  
SELECTING A DIFFERENT  
CHANNEL  
If you encounter interference while using  
your phone, you can manually change the  
phone´s channel for clear operation. This  
function works only when the phone is in  
use. Press CH/DELETE. ¨Scanning¨  
appears on the display, indicating the phone  
is changing to another channel.  
15  
 
     
PAGE  
Ô NOTES Ô  
To locate the handset (while it’s off the  
base), press PAGE on the base. The  
handset beeps for 60 seconds. Paging is  
canceled when pressing any handset key or  
the handset is returned to the base. Ô  
Page  
You can cancel paging by  
pressing PAGE on the  
base.  
Flash and Call Waiting  
You must subscribe through  
your local telephone  
company to receive Call  
Waiting Service.  
FLASH AND CALL WAITING  
If you have “Call Waiting” service and a call  
waiting tone sounds while you are on a call,  
press TALK/FLASH to accept the waiting  
call. There is a short pause. Then you will  
hear the new caller. To return to the original  
caller, press TALK/FLASH again.Ô  
Voice Mail Waiting  
Indicator  
You must subscribe to  
voice mail service from your  
telephone company in order  
to use this feature. The  
voice mail company will  
provide you with the access  
number.  
VOICE MAIL WAITING  
INDICATOR  
If you subscribe to voice mail service, you  
can use your cordless telephone to access  
your voice mailbox. The CHARGE/IN USE  
light on the base of your phone flashes  
whenever you have messages waiting in  
your voice mailbox. Just program SPEED  
DIAL with your access number and you can  
get your messages at the touch of a button.  
(The voice mail service provider will supply  
you with the access number. This number  
may be simply a phone number. Refer to  
the provider’s literature.)Ô  
You may need to occasionally reset the  
indicator if it remains On after you have  
retrieved your messages. To reset the  
indicator, press and hold PAGE for five  
seconds.  
16  
 
     
SETTING MENU OPTIONS  
There are five setup options available. They  
are Auto Talk, CIDCW (Caller ID on Call  
Waiting), Area Code, Dial and Language.  
Auto Talk allows you to answer the phone  
without pressing TALK/FLASH.  
If the phone rings when Auto Talk is On,  
simply remove the handset from the base  
and the phone automatically answers the  
call. If the phone rings when Auto Talk is  
Off, you must press TALK/FLASH to answer  
the call. Ô  
Ô NOTE Ô  
The Cordless phone  
features include Auto Talk  
and Auto Standby. Auto  
Standby allows you to hang  
up by simply returning the  
handset to the base.  
Changing the Auto Talk and  
CIDCW  
1. Press and hold CID/MENU.  
2. Use  
VOL or  
VOL keys to move the  
pointer to the selection that you would  
like to change. Press SELECT to toggle  
between ¨On¨ and ¨Off¨ for Auto Talk  
and CIDCW.  
3. Press END and return the handset to  
the base unit to complete the setting.  
The handset returns to the standby  
mode.  
Entering Your Area Code  
If you enter a three-digit area code number  
in the Area Code option, your local area  
code does not appear in Caller ID  
messages. Do not program this option if  
your calling area requires ten-digit dialing.  
When reviewing Caller ID messages, you  
will see only the local seven digit number.  
For calls received from outside your local  
area code, you will see a full ten-digit  
number.  
17  
 
     
1. When the phone is in the standby  
mode, press and hold CID/MENU. The  
Caller ID setting screen appears.  
Ô NOTES Ô  
Entering Your Area Code  
When the area code has  
2. Press VOL key twice to select ¨Area  
already been stored in  
memory, the stored area  
code will be displayed. To  
change it, use the CH/  
Code¨.  
3. Press SELECT. Ô  
DELETE and number keys  
to enter the new area code.  
Then press SELECT. A  
confirmation tone sounds.  
To complete the setting,  
press END or return the  
handset to the base unit.  
4. Use the number keys (0 - 9), or CH/  
DELETE to enter the three-digit area  
code.  
5. Press SELECT. A confirmation tone  
sounds and the displayed area code is  
entered.  
Choosing the Dialing  
Mode  
Make sure your battery  
pack is fully charged  
before choosing the dialing  
mode.  
6. Press END or return the handset to the  
base unit to complete the setting. The  
handset returns to the standby mode.  
Choosing the Dialing Mode  
Most phone systems use tone dialing which  
sends DTMF tones through the phone lines.  
However some phone systems still use  
pulse dialing such as in rural areas. Ô  
The default setting is tone dialing.  
Depending on your dialing system, set the  
mode as follows:  
1. When the phone is in the standby  
mode, press and hold CID/MENU.  
2. Press  
¨Dial¨.  
VOL key three times to select  
3. Press SELECT to toggle between  
¨Tone¨ and ¨Pulse¨ for each setting.  
4. Press END or return the handset to the  
base unit to complete the setting. The  
handset returns to the standby mode.  
18  
 
 
• If you are not sure of your dialing  
system, set for tone dialing. Make a  
trial call.  
If the call connects, leave the setting  
as is, otherwise set for pulse dialing.  
• If your phone system requires pulse  
dialing and you need to send the  
DTMF tones for certain situations  
during a call, you may “switch-over”  
to tone dialing. (Refer to “Tone  
Dialing Switch-over” on page 15.)  
Setting the Language  
1. When the phone is in the standby  
mode, press and hold CID/MENU.  
2. Press  
VOL key four times to select  
¨Language¨.  
3. Press SELECT to toggle between  
¨Eng¨(English), ¨Fr.¨(French) and  
¨Esp¨(Spanish) for each setting.  
4. Press END or return the handset to the  
base unit to complete the setting. The  
handset returns to the standby mode.  
MEMORY DIALING  
STORING PHONE NUMBERS  
Ô NOTE Ô  
In memory dialing  
operation, you must press  
a key within 30 seconds or  
the phone will return to the  
standby mode. If you  
AND NAMES  
Memory Dialing allows you to dial a number  
using just a few key presses. Your cordless  
telephone stores up to ten names/numbers  
in the handset. Ô  
return the handset to the  
base, the phone will return  
to the standby mode also.  
1. Press MEM, ¨Select Memory¨ is  
displayed.  
2. Press  
VOL or  
VOL keys, or enter a  
number (0 - 9) to select the memory  
location where you would like to store  
the number.  
19  
 
       
3. Press MEM or SELECT.  
4. Press MEM or SELECT. A cursor flashes  
indicating that the display is ready for  
the name to be entered.  
If “Edit MemoryXX” appears, the  
selected memory location is already  
stored. Then you must either edit the  
entry in this location, delete the entry in  
this location, or select ¨Go Back¨ to  
choose another location.  
5. To enter a name (up to 13 characters),  
use the number keys.  
• See “Steps for Entering Names and  
Special Characters” on page 21.  
• Use #/> and /TONE/< to move the  
cursor to the desired location.  
• Use CH/DELETE to delete characters  
as needed.  
• Press and hold CH/DELETE to delete  
all the characters.  
• If a name is not required, go to step  
6.  
6. Press MEM or SELECT. ¨Store  
Number¨ is displayed.  
The cursor flashes indicating that the  
display is ready for the number to be  
entered.  
7. Use the number keys to enter the  
phone number.  
• The phone number cannot exceed  
20 digits.  
20  
 
 
• Use PAUSE/REDIAL to enter a pause  
in the dialing sequence. The display  
shows a ¨P¨. Each pause counts as  
one digit and represents a two  
second delay of time between the  
digits. Ô  
Ô NOTE Ô  
The pause feature is useful  
for long distance calling,  
credit card dialing, or  
• Use CH/DELETE to delete digits as  
needed.  
sequences that require a  
pause between digits.  
8. Press MEM or SELECT. You will hear a  
confirmation tone. Memory storage is  
complete. For example, if you store a  
name and number into memory  
location number 01, the display shows  
¨Memory01 Stored¨.  
After about two seconds, the Select  
Memory screen is displayed.  
Repeat steps 2 - 8 to store more  
numbers.  
9. Press END to return to the standby  
mode.  
STEPS FOR ENTERING NAMES  
AND SPECIAL CHARACTERS  
Refer to the letters on the number keys to  
select the desired characters.  
With each press of a numeric key, the  
displayed character appears in the following  
order: Upper case letters first, lower case  
letters next and finally the number  
corresponding to the key.  
21  
 
 
For example, to enter Movies.  
1. Pick up the handset. Press MEM.  
2. Enter a number or press  
VOL or  
VOL keys to select a memory location.  
3. Press MEM or SELECT.  
4. Press MEM or SELECT. (When there is  
information already stored in the  
selected memory location, ¨Edit  
MemoryXX¨ is displayed. See “Editing a  
Stored Name and/or Phone Number”  
on page 24 for information.)  
5. Press 6. Then press #/>to move the  
Ô NOTE Ô  
cursor to the right. Ô  
If the next character uses  
the same number key, you  
must press #/> to move the  
cursor over. Otherwise the  
next time you press the  
number key, it changes the  
character that was  
6. Press 6 six times.  
7. Press 8 six times.  
8. Press 4 six times.  
9. Press 3 five times.  
previously set.  
10. Press 7 eight times.  
11. When finished, press MEM or SELECT.  
To continue to store the telephone number,  
proceed to step 7 on “Storing Phone  
Numbers and Names” on page 20.  
If you make a mistake while  
entering a name  
Use /TONE/< or #/> to move the cursor to  
the incorrect character.  
Press CH/DELETE to erase the wrong  
character. Then enter the correct character.  
To delete all characters, press and hold CH/  
DELETE.  
22  
 
 
MAKING CALLS WITH  
MEMORY DIALING  
Ô NOTES Ô  
Memory Dialing from  
Standby Mode  
Memory Dialing from Standby  
Mode  
If you press SELECT  
before TALK/FLASH,  
you can confirm the  
name and the number  
stored in the selected  
memory location.  
1. Press MEM. The handset displays your  
programmed memory locations.  
2. Press  
VOL or  
VOL keys, or enter  
the number (0 - 9) to select the memory  
location you would like to dial. Ô  
To exit the memory  
function without dialing,  
press END. The  
handset returns to the  
standby mode.  
3. Press TALK/FLASH. ¨Talk¨ and the  
volume setting appear on the display.  
Then the displayed number is dialed. Ô  
Whenever you are  
using a memory menu  
screen, you must press  
a key within 30 seconds  
or the phone will return  
to the standby mode.  
Memory Dialing from Talk Mode  
1. Press TALK/FLASH. ¨Talk¨ and the  
volume setting appears.  
2. Press MEM.  
Memory Dialing from  
Talk Mode  
If you select a memory  
3. Press  
VOL or  
VOL keys or enter a  
number (0 - 9) to select the memory  
location of the desired phone number.  
The selected name is displayed. Ô  
location that does not have  
a stored number, the  
phone will not dial.  
4. The phone number in the memory will  
be dialed when SELECT is pressed.  
5. To hang up, press END.  
CHAIN DIALING  
The memory locations on the handset are  
not limited to phone numbers. You can also  
store a group of numbers (up to 20 digits)  
that you need to enter once your call  
connects. This is referred to as Chain  
Dialing.  
23  
 
       
An example of this is a bank account  
number. Once you have called your bank,  
and are prompted to enter the account  
number, press MEM and select the location  
number where the special number has been  
stored. Then press SELECT.  
Store your special number with an  
identifying name. (Refer to “Memory  
Dialing” on page 19.)  
EDITING A STORED NAME  
AND/OR PHONE NUMBER  
1. Press MEM, ¨Select Memory¨ is  
displayed.  
2. Press  
VOL or  
VOL keys, or enter a  
number (0 - 9) to select the memory  
location you would like to edit, and  
press MEM or SELECT.  
The screen appears with the memory  
location number that you have selected  
in the display.  
3. Press MEM or SELECT.  
4. Press  
VOL or  
VOL keys to select  
¨Edit MemoryXX¨. Then press MEM  
or SELECT. Store Nameis displayed.  
The cursor flashes indicating that the  
display is ready for the name to be  
edited. When a name has not been  
stored, the cursor appears at the  
beginning of the second line.  
5. Use the number keys, /TONE/<, #/>, or  
CH/DELETE to edit the name. (See  
“Storing Phone Numbers and Names”  
on page 19.) To edit only the phone  
number, skip this step.  
24  
 
 
6. Press MEM or SELECT. The cursor  
flashes indicating that the display is  
ready for the number to be edited.  
7. Use the number key, /TONE/<, #/>,  
PAUSE/REDIAL or CH/DELETE to edit  
the phone number. The phone number  
cannot exceed 20 digits.  
If you don’t want to change the phone  
number, skip this step.  
8. Press MEM or SELECT. If you changed  
either name or phone number, a  
confirmation display shows up. If it is  
correct, press  
VOL key to select  
Yes” and press SELECT. You hear a  
confirmation tone. The memory storage  
is complete.  
For example, if you store a name and  
number into memory location number  
01, the display shows ¨Memory01  
Stored¨. After about two seconds,  
Select Memory screen is displayed.  
9. Press END to return to the standby  
mode.  
ERASING A STORED NAME  
AND PHONE NUMBER  
1. Press MEM, ¨Select Memory¨ is  
displayed.  
2. Press  
VOL or  
VOL keys, or enter a  
number (0 - 9) to select the memory  
location you would like to erase.  
3. Press MEM or SELECT.  
The screen appears with the memory  
location number that you have selected  
in the display.  
25  
 
 
4. Press MEM or SELECT.  
5. Press VOL key to move the pointer  
down to ¨Delete MemoryXX¨.  
6. Press MEM or SELECT. The  
confirmation screen appears.  
7. Press VOL key to move the pointer to  
¨Yes¨.  
8. Press SELECT or CH/DELETE.  
You hear a confirmation tone.  
9. After about two seconds, the display  
returns to the Select Memory screen.  
You may delete the information in  
another memory location (return to step  
2) or press END to return to the standby  
mode.  
TESTING STORED EMERGENCY  
NUMBERS  
If you store an emergency service’s number  
(police department, fire department,  
ambulance) and you choose to test the  
stored number, make the test call during the  
late evening or early morning hours to avoid  
peak demand periods. Also, remain on the  
line to explain the reason for your call.  
ONE-TOUCH SPEED DIAL  
You can store your most frequently dialed  
number in the SPEED DIAL location. The  
One-touch speed dial allows you to dial a  
number with one key press. (There is no  
need to press TALK/FLASH. The phone will  
automatically dial the number stored.)  
26  
 
   
STORING AND EDITING THE  
Ô NOTES Ô  
Storing and Editing the  
Speed Dial  
Number stored in SPEED  
SPEED DIAL  
1. When the phone is in the standby  
mode, press and hold SPEED DIAL. Ô  
DIAL is independent from  
the numbers stored in  
Memory Dial locations.  
If “Edit Number” appears, there is a  
number already stored. Press  
or VOL keys to select ¨Edit  
Number¨. Then press SELECT.  
VOL   
Making Calls with the  
Speed Dial  
If the SPEED DIAL does  
not have a stored number,  
the handset will beep  
rapidly and the phone will  
not dial.  
2. Store the number by following step 7  
under “Storing Phone Numbers and  
Names” on page 20.  
3. Press SELECT.  
You hear a confirmation tone. Memory  
storage is complete.  
MAKING CALLS WITH THE  
SPEED DIAL  
When the phone is in the standby mode,  
simply press SPEED DIAL. The number  
stored in the SPEED DIAL memory location  
is instantly dialed. Ô  
DELETING THE SPEED DIAL  
1. When the phone is in the standby  
mode, press and hold SPEED DIAL.  
2. Press  
VOL or  
VOL keys to select  
¨Delete Number¨.  
3. Press SELECT.  
4. Press VOL key to move the pointer to  
¨Yes¨.  
5. Press SELECT or CH/DELETE.  
You hear a confirmation tone. After  
about two seconds, the handset returns  
to the standby mode.  
27  
 
     
CALLER ID  
You must subscribe to Caller ID service  
to use this feature.  
Ô NOTES Ô  
When the telephone rings, the Caller ID  
feature allows you to view the caller´s name  
and phone number on the display before  
you answer the phone. The handset  
displays the phone number of the incoming  
call, the name, and time. Additionally, you  
can dial the displayed number and store the  
information for memory dialing. Make sure  
you have turned on the Caller ID on Call  
Waiting feature. (See “changing the Auto  
Talk and CIDCW” on page 17.)  
If you answer a call  
before the Caller ID  
message is received  
(Example: before the  
second ring), the Caller  
ID message will not  
appear.  
When the call is  
received via a  
telephone company that  
does not offer Caller ID  
service, the caller´s  
phone number and  
name do not appear.  
(This includes  
WHEN THE TELEPHONE RINGS  
1. When the Caller ID message is  
received, the display shows the caller´s  
phone number along with the date and  
time. The incoming call information is  
stored in the Caller ID record. If the  
Caller ID service includes the caller´s  
name, the caller´s name appears on  
the display (up to 15 letters). Ô  
international calls.)  
When the call is via a  
private branch  
exchange (PBX), the  
caller´s phone number  
and name may not  
appear.  
Data errors appear as  
¨
¨.  
You may receive any one of the  
following messages:  
Message  
Display  
When invalid data is “Incomplete Data”  
received  
When a private name “Private Name”  
is received  
When a private  
number is received  
“Private Number”  
“Unknown Name”  
“Unknown Number”  
When an unknown  
name is received  
When an unknown  
number is received  
28  
 
   
2. When you pick up the phone, the  
display changes to ¨Talk¨. (Auto Talk  
feature is set to on.)  
VIEWING THE CALLER ID  
Ô NOTES Ô  
Viewing the Caller ID  
Message List  
MESSAGE LIST  
The Caller ID list stores information for up to  
30 incoming calls - even unanswered calls.  
Ô
In Caller ID operation, if  
no key is pressed for  
more than 30 seconds,  
an error tone sounds  
and the telephone  
returns to the standby  
mode.  
1. Press CID/MENU.  
The summary screen appears. The  
screen shows the number of new  
messages and total messages.  
If a call comes in via a  
telephone system that  
does not offer Caller ID  
service, no information  
is stored.  
2. Press  
VOL key to display the latest  
Caller ID message.  
3. Press  
VOL key to see the next  
message. Or press  
the previous message.  
VOL key to see  
Each message can be  
up to 15 characters for  
the phone number and  
the name.  
4. Press END to return to the standby  
mode.  
The number of calls  
from the same Caller ID  
appears next to the  
received time. Once you  
view the new message,  
the number will  
DELETING INFORMATION  
FROM THE CALLER ID LIST  
The cordless phone stores up to 30  
messages. If the phone receives the 31st  
message, the oldest one in the list is  
automatically deleted and the newest is  
stored. Caller ID data can also be deleted  
manually. Ô  
disappear.  
Deleting Information  
from the Caller ID List  
While using the ¨Delete  
All?¨ or ¨Delete  
Message?¨ screen if no  
key is pressed for more  
than 30 seconds, an error  
tone sounds and the  
telephone returns to the  
standby mode.  
Deleting a Caller ID Message  
1. Press CID/MENU. Display the message  
to be deleted from the Caller ID list by  
pressing  
VOL or  
VOL keys.  
2. Press CH/DELETE.  
29  
 
     
3. Press  
VOL or  
VOL keys to select  
¨Yes¨ or ¨No¨.  
4. Press SELECT or CH/DELETE.  
When the pointer is at ¨Yes¨: Ô  
A tone sounds and the Caller ID  
message is deleted. The next Caller ID  
message is then displayed.  
Ô NOTES Ô  
Deleting a Caller ID  
Message  
If you get an incoming call  
or page, the deleting  
operation is canceled and  
you can answer the call or  
page.  
When the pointer is at ¨No¨:  
The display returns to the Caller ID  
message.  
Deleting all Caller ID Names/  
Numbers  
Calling a Party from the  
Caller ID List  
1. Press CID/MENU.  
You cannot make a call  
from the Caller ID list if  
your cordless telephone  
is connected to a  
private branch  
exchange (PBX).  
2. Press CH/DELETE.  
3. Press  
VOL or  
VOL keys to select  
¨Yes¨ or ¨No¨.  
You can place a call  
from talk mode. Press  
TALK/FLASH. Then  
press CID/MENU.  
Select the phone  
number that you want to  
dial by pressing the  
4. Press SELECT or CH/DELETE.  
When the pointer is at ¨Yes¨:  
A tone sounds and all stored Caller ID  
messages are deleted.  
When the pointer is at ¨No¨:  
The display returns to the summary  
screen.  
VOL or  
VOL key.  
Press SELECT.  
The displayed phone  
number will be dialed.  
USING THE CALLER ID LIST  
Calling a Party from the Caller  
ID List  
You can place a call from the Caller ID list.  
The cordless phone stores up to 30  
messages.Ô  
30  
 
     
1. Press CID/MENU. Select the phone  
number that you want to dial by  
pressing  
VOL or  
VOL keys.  
2. Press TALK/FLASH. The displayed  
phone number dials automatically.  
Long Distance Calls and Area  
Code Setting/Cancellation  
Pressing 1 while the incoming Caller ID  
information is displayed will place or remove  
the prefix 1in the display to set up for a long  
distance call or cancel. Pressing 3 will set or  
cancel an area code setting. Ô  
Ô NOTES Ô  
Long Distance Calls and  
Area Code Setting/  
Cancellation  
When a long distance call  
has been set, ¨1¨ appears  
Storing Caller ID Messages in  
Memory Dialing  
in the display.  
Storing Caller ID  
Messages in Memory  
Dialing  
Messages shown in the Caller ID list can be  
stored in memory dialing. Using the  
incoming call information (i.e., Caller ID list),  
the phone number of the party on the Caller  
ID list can be stored in memory.Ô  
You cannot store a  
Caller ID message if no  
phone number appears  
in the message.  
1. Press CID/MENU.  
If a message has  
already been stored in  
the selected memory  
number location, a  
confirmation screen is  
displayed.  
Select the phone number to be stored  
from the Caller ID list by pressing  
VOL or  
2. Press MEM.  
3. Press VOL or  
VOL keys.  
Press  
VOL key to  
select ¨Yes¨. Press  
SELECT to overwrite.  
The display returns to  
the Caller ID list.  
VOL keys or enter a  
number (0 - 9) to select the memory  
location to be stored.  
4. Press SELECT. Ô  
You hear a confirmation tone, and the  
number is stored in memory. The  
display returns to the Caller ID list.  
31  
 
   
ADDITIONAL  
INFORMATION  
INSTALLING THE BELTCLIP  
To attach the beltclip  
Insert the beltclip into the holes on each  
side of the handset. Press down until it  
clicks.  
To remove the beltclip  
Pull both sides of the beltclip to release the  
tabs from the holes.  
HEADSET INSTALLATION  
You can connect an optional headset with a  
3/32-inch (2.5-mm) plug. Contact  
RadioShack for a suitable headset.  
To connect the headset, open the rubber  
cover on the side of the handset. Then  
insert the headset’s plug into the jack.Ô  
Ô NOTES Ô  
If you place the handset  
on the base to recharge  
it while the headset is  
connected, be sure the  
handset seats properly.  
When you finish using the headset,  
disconnect it from the handset and close the  
rubber cover to protect the jack.  
You can use a handset  
holder (available from  
your local RadioShack  
store) to hang the  
handset on your belt for  
greater convenience  
when using a headset.  
32  
 
           
TROUBLESHOOTING  
If your phone is not performing to your expectations, please try these  
simple steps first  
Problem  
Solution  
• Make sure the AC adapter is plugged into the  
base and wall outlet.  
• Make sure the handset is properly seated on the  
base.  
• Make sure the charging contacts on the handset  
are clean.  
The CHARGE/IN USE  
indicator won’t illuminate  
when the handset is placed  
on the base.  
• Move the handset and/or base to a different  
location away from metal objects or appliances  
and try again.  
• Press CH/DELETE to help eliminate  
background noise.  
The audio sounds weak  
and/or scratchy.  
• Make sure that the handset is not too far from  
the base.  
• Check both ends of the base telephone line cord.  
• Make sure the AC adapter is plugged into the  
base and wall outlet.  
Can’t make or receive calls. • Disconnect the AC adapter for a few minutes.  
Then reconnect it.  
• Make sure that the handset is not too far from  
the base.  
• The battery pack may be weak. Charge the  
battery for 15-20 hours.  
The handset doesn’t ring or • The handset may be too far away from the base  
receive a page.  
unit.  
• Place the base unit away from appliances or  
metal objects.  
• Keep the handset away from microwave ovens,  
computers, remote control toys, wireless  
microphones, alarm systems, intercoms, room  
monitors, fluorescent lights, and electrical  
appliances.  
Severe noise interference.  
• Move the base to another location or turn off the  
source of interference.  
33  
 
 
Problem  
Solution  
• The handset was picked up before the second  
ring.  
The Caller ID does not  
display.  
• The call was placed through a switchboard.  
• Call your local telephone company to verify your  
Caller ID service is current.  
• Charge the handset.  
• Contact your local telephone company to make  
sure that your telephone receives FSK message  
signaling.  
Voice Message Indication  
does not work.  
If you still have problems, disconnect the phone. If other phones on the  
same line work properly, the fault is in this phone or its installation. If you  
cannot find the problem, take the phone to your local RadioShack store  
for assistance.  
CARE  
Keep the phone dry; if it gets wet, wipe it dry immediately. Use and store  
the phone only in normal temperature environments. Handle the phone  
carefully; do not drop it. Keep the phone away from dust and dirt, and  
wipe it with a damp cloth occasionally to keep it looking new.  
SERVICE AND REPAIR  
If your phone is not performing as it should, take it to your local  
RadioShack store for assistance. To locate your nearest RadioShack,  
use the store locator feature on RadioShack’s website  
the menu options. Modifying or tampering with the phone’s internal  
components can cause a malfunction and might invalidate its warranty  
and void your FCC authorization to operate it.  
34  
 
   
NOTE  
35  
 
Limited One-Year Warranty  
This product is warranted by RadioShack against manufacturing defects in material and  
workmanship under normal use for one (1) year from the date of purchase from RadioShack  
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS  
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IM-  
PLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE  
WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED  
HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER  
OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR  
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE  
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT  
NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF  
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCI-  
DENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or  
limitation of incidental or consequential damages, so the above limitations or exclusions may  
not apply to you.  
In the event of a product defect during the warranty period, take the product and the Ra-  
dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will,  
at its option, unless otherwise provided by law: (a) correct the defect by product repair with-  
out charge for parts and labor; (b) replace the product with one of the same or similar design;  
or (c) refund the purchase price. All replaced parts and products, and products on which a re-  
fund is made, become the property of RadioShack. New or reconditioned parts and products  
may be used in the performance of warranty service. Repaired or replaced parts and prod-  
ucts are warranted for the remainder of the original warranty period. You will be charged for  
repair or replacement of the product made after the expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,  
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper  
installation or maintenance, alteration, lightning or other incidence of excess voltage or cur-  
rent; (b) any repairs other than those provided by a RadioShack Authorized Service Facility;  
(c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, ship-  
ping or insurance costs; or (f) costs of product removal, installation, set-up service adjust-  
ment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary  
from state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102  
12/99  
43-3557/43-3558  
UPZZ01040BA  
01A04  
Printed in China  
RadioShack Corporation  
Fort Worth, Texas 76102  
 

QSC Audio Speaker GP218 sw User Guide
Q See Speaker System NS BT007 User Guide
Radio Shack Cordless Telephone 43 3534 User Guide
Radio Shack Two Way Radio 05A03 User Guide
Ramsey Electronics Satellite Radio FT146 User Guide
Raypak Water Heater 992BD 2342BD User Guide
Ryobi Pole Saw RY43160 User Guide
Ryobi Trimmer P2601 User Guide
Samsung CRT Television TXJ1366 User Guide
Samsung Home Theater System HT C5200 User Guide