Radio Shack Cordless Telephone 43 1122 User Guide

900MHz Cordless Telephone  
with Call Waiting/Caller ID  
 
you can take the necessary steps to prevent  
interruption of your telephone service.  
7. Do not fix the AC power supply cord to  
building surfaces with metal fittings (if  
the product has an AC power cord).  
LIGHTNING  
8. Unplug this product from the wall outlet  
before cleaning. Do not use liquid  
cleaners or aerosol cleaners. Use a  
damp cloth for cleaning.  
Your telephone has built-in protection circuits  
to reduce the risk of damage from surges in  
telephone line and power line current. These  
protection circuits meet or exceed the FCC  
requirements. However, lightning striking the  
telephone or power lines can damage your  
telephone.  
9. Do not use this product near water, for  
example, near a bathtub, wash bowl,  
kitchen sink, or laundry tub, in a wet  
basement, or near a swimming pool.  
Lightning damage is not common.  
10. Do not place this product on an unstable  
cart, stand, or table. The product may  
fall, causing serious damage to the  
product.  
Nevertheless, if you live in an area that has  
severe electrical storms, we suggest that you  
unplug your phone when storms approach to  
reduce the possibility of damage.  
11. Slots and openings in the cabinet and  
the back or bottom are provided for  
ventilation. To protect it from  
IMPORTANT SAFETY  
INSTRUCTIONS  
overheating, these openings must not  
be blocked or covered. The openings  
should never be blocked by placing the  
product on a bed, sofa, rug, or other  
similar surface. This product should  
never be placed near or over a radiator  
or heat register. This product should not  
be placed in a built-in installation unless  
proper ventilation is provided.  
When using your telephone equipment,  
basic safety precautions should always be  
followed to reduce the risk of fire, electric  
shock and injury to persons, including the  
following:  
1. Read and understand all instructions.  
2. Follow all warnings and instructions  
marked on the product.  
12. This product should be operated only  
from the type of power source indicated  
on the marking label. If you are not sure  
of the type of power supply to your  
home, consult your local power  
company.  
3. Never install telephone wiring during a  
lightning storm.  
4. Never install telephone jacks in wet  
locations unless the jack is specifically  
designed for wet locations.  
13. Do not allow anything to rest on the  
power cord. Do not locate this product  
where the cord will be stepped on.  
5. Never touch uninstalled telephone wires  
or terminals unless the telephone line  
has been disconnected at the network  
interface.  
14. Do not overload wall outlets and  
extension cords as this can result in a  
risk of fire or electric shock.  
6. Use caution when installing or modifying  
telephone lines.  
15. Never push objects of any kind into this  
product through cabinet slots as they  
3
Important Information  
 
may touch dangerous voltage points or  
short out parts that could result in a risk  
of fire or electric shock. Never spill liquid  
of any kind on the product.  
19. Do not use the telephone to report a gas  
leak in the vicinity of the leak.  
Battery Safety Instructions  
16. To reduce the risk of electric shock, do  
not disassemble this product. Take it to  
a qualified service technician when  
service or repair work is required.  
Opening or removing covers may  
expose you to dangerous voltage or  
other risks. Incorrect reassembly can  
cause electric shock when the product is  
subsequently used.  
Caution:  
read and follow these instructions.  
To reduce the risk of fire or injury,  
1. Use only the appropriate type and size  
battery pack specified in the instruction  
manual provided for this product.  
2. Do not dispose of the battery pack in a  
fire. The cell may explode. Check with  
local codes for possible special disposal  
instructions.  
17. Unplug this product from the wall outlet  
and refer servicing to qualified service  
personnel under the following  
conditions:  
3. Do not open or mutilate the battery  
pack. Released electrolyte is corrosive  
and may cause damage to the eyes or  
skin. It may be toxic if swallowed.  
• When the power cord plug is  
damaged or frayed.  
4. Exercise care in handling the battery  
pack in order not to short it with  
conducting materials such as rings,  
bracelets, and keys. The battery or  
conductor may overheat and cause  
burns.  
• If liquid has been spilled, into the  
product.  
• If the product has been exposed to  
rain or water.  
• If the product does not operate  
normally by following the operating  
instructions. Adjust only those  
controls that are covered by the  
operating instructions because  
improper adjustment of other controls  
may result in damage and will often  
require extensive work by a qualified  
technician to restore the product to  
normal operation.  
5. Charge the battery pack provided or  
identified for use with this product only in  
accordance with the instructions and  
limitations specified in the instruction  
manual provided for this product.  
6. Observe proper polarity orientation  
between the battery pack and battery  
charger.  
SAVE THESE INSTRUCTIONS  
• If the product has been dropped or  
the cabinet has been damaged.  
• If the product exhibits a distinct  
change in performance.  
18. Avoid using a telephone (other than a  
cordless type) during an electrical storm.  
There may be a remote risk of electric  
shock from lightning.  
4
Important Information  
 
ˆ Contents  
Important Information ........................................................................................................... 2  
Features .................................................................................................................................. 6  
Installation .............................................................................................................................. 7  
Selecting a Location ......................................................................................................... 7  
On a Desk Top .......................................................................................................... 7  
On a Wall Plate ......................................................................................................... 7  
Connecting and Charging the Battery Pack ..................................................................... 8  
Setting the Dialing Mode .................................................................................................. 9  
Setting the Ringer Tone and Volume .............................................................................. 10  
Turning Auto Talk On/Off ................................................................................................ 10  
Turning Caller ID/Call Waiting On/Off ............................................................................. 10  
Storing Your Area Code .................................................................................................. 10  
Selecting the Language ................................................................................................... 11  
Operation .............................................................................................................................. 11  
Making and Receiving Calls ............................................................................................ 11  
Selecting the Channel ..................................................................................................... 11  
Adjusting the Handset’s Volume ..................................................................................... 12  
Using Redial ................................................................................................................... 12  
Using Flash ..................................................................................................................... 12  
Using Tone Services on a Pulse Line ............................................................................. 12  
Paging ............................................................................................................................ 12  
Using a Headset ............................................................................................................. 12  
Memory Dialing ............................................................................................................... 13  
Storing a Number and Name in Memory ................................................................. 13  
Entering a Pause ..................................................................................................... 14  
Editing or Deleting a Number in Memory ................................................................ 14  
Reviewing Memory Numbers .................................................................................. 14  
Dialing a Memory Number ....................................................................................... 14  
Chain-Dialing Service Numbers .............................................................................. 15  
Testing Stored Emergency Numbers ....................................................................... 15  
Caller ID Operation .............................................................................................................. 15  
Important Caller ID Information ...................................................................................... 15  
Reviewing Caller ID Records .......................................................................................... 15  
Caller ID Messages ................................................................................................. 16  
Adding/Deleting the Area Code ...................................................................................... 16  
Dialing Numbers from a Caller ID Record ...................................................................... 16  
Storing a Caller ID Record in Memory ............................................................................ 16  
Deleting Caller ID Records ............................................................................................. 17  
Deleting a Single Caller ID Record .......................................................................... 17  
Deleting All Caller ID Records ................................................................................. 17  
Troubleshooting ................................................................................................................... 18  
Care ................................................................................................................................ 19  
5
Contents  
 
ˆ Features  
Bilingual Display  
either English or French.  
Thank you for purchasing the RadioShack  
900 MHz Cordless Telephone. Your phone  
uses advanced technology to give you  
superior audio quality and extended range.  
The phone’s Caller ID unit records each  
caller’s telephone number (and name, if  
available in your area) and the date and time  
of the call, as provided by your local phone  
company to Caller ID service subscribers. If  
you subscribe to Call Waiting with Caller ID,  
the phone shows you the incoming caller  
information, even when you are already  
talking on the phone.  
—displays the message in  
Ample Talk and Standby Time  
— the  
supplied battery (when fully charged)  
provides about 7 hours of talk time or 14  
days of standby time.  
Security Access-Protection Code  
automatically prevents other cordless phone  
users from using your phone line while the  
handset is off the base.  
Auto Talk  
— lets you set the phone to  
answer a call by simply lifting the handset  
from the base.  
Your phone’s other features include:  
10-Number Memory Dialing  
store up to 10 numbers in memory for easy  
dialing.  
— lets you  
Important:  
• Cordless phones such as this one  
require AC power to operate. When the  
power is off, you cannot make or receive  
calls using your phone. To be safe, you  
should also have a phone that does not  
need AC power to operate (not a  
cordless phone), so you can still make  
and receive calls if there is an AC power  
failure.  
Headset Jack  
optional headset for hands-free  
convenience.  
— lets you connect an  
Hearing-Aid Compatibility  
the phone with hearing aids that have a T  
(telephone) switch.  
— lets you use  
30-Record CID Capacity  
call records in Caller ID.  
— stores up to 30  
• When AC power is lost, the phone loses  
the security access-protection code  
connection between the base and the  
handset. When power is restored, put  
the handset on the base briefly to  
restore this connection so you can use  
the handset.  
Volume Control  
— lets you adjust the  
volume you hear through the handset.  
Page  
— lets you send a signal from the base  
to the handset to page someone or to help  
you locate the handset.  
Your phone operates on standard radio  
frequencies as allocated by the FCC. It  
is possible for other radio units operating  
nearby on similar frequencies to  
unintentionally intercept your  
conversation or cause interference. This  
possible lack of privacy can occur with  
any cordless phone.  
Adjustable Ringer/Tone Volume  
you choose between two volumes and tones  
for the phone’s ringer.  
— lets  
Facedown or Faceup Handset Charging  
— you can place the handset on the base  
facedown or faceup to show the Caller ID  
display.  
6
Features  
 
ˆ Installation  
using jacks and adapters (available at your  
local RadioShack store), or have the  
telephone company update the wiring for  
you. You must use compatible modular jacks  
that are compliant with Part 68 of FCC Rules.  
SELECTING A LOCATION  
You can place the phone’s base on a desk or  
table, or mount it on a standard wall plate or  
directly on a wall. Select a location that is:  
• near an accessible AC outlet  
• near a telephone line jack  
Note:  
The USOC number of the jack to be  
installed is RJ11C (or RJ11W for a wall plate  
jack).  
• out of the way of normal activities  
On a Desk Top  
• away from electrical machinery,  
electrical appliances, metal walls or  
filing cabinets, wireless intercoms,  
alarms, and room monitors  
Follow these steps to place the base on a  
desk, shelf, or table.  
1. Plug one end of the supplied long  
TEL LINE  
modular cord into the  
the back of the base.  
jack on  
• away from other cordless phones  
The base’s location affects the handset’s  
range. If you have a choice of several  
locations, try each to see which provides the  
best performance.  
2. Plug the modular cord’s other end into a  
modular phone line jack.  
3. Insert the supplied AC adapter’s barrel  
DC IN 9V  
plug into the  
the base.  
jack on the back of  
Cautions:  
You must use a Class 2 power  
source that supplies 9V DC  
and delivers at least 210 mA.  
4. Route the adapter’s cord through the  
strain relief slot on the base.  
!
Its center tip must be set to positive and  
5. Plug the adapter into a standard AC  
outlet.  
DC IN 9V  
its plug must fit the phone's  
jack. The supplied adapter meets these  
specifications. Using an adapter that  
does not meet these specifications  
could damage the phone or the adapter.  
6. Lift the base’s antenna to a vertical  
position.  
On a Wall Plate  
• Always connect the AC adapter to the  
phone before you connect it to AC  
power. When you finish, disconnect the  
adapter from AC power before you  
disconnect it from the phone.  
1. Plug one end of the supplied short  
TEL LINE  
modular cord into the  
the back of the base.  
jack on  
2. Insert the supplied AC adapter’s barrel  
Your telephone connects directly to a  
modular telephone line jack. If your  
telephone wiring does not have a modular  
jack, you can update the wiring yourself  
DC IN 9V  
plug into the  
the base.  
jack on the back of  
7
Installation  
 
3. Route the adapter and modular cords  
through the grooves on the bottom of  
the base.  
6. Plug the modular cord’s other end into  
the phone jack, and plug the adapter  
into a standard AC outlet.  
4. Plug the short modular cord into the wall  
plate jack, then align the base’s keyhole  
slots with the wall plate studs and slide  
the base down to secure it.  
CONNECTING AND  
CHARGING THE BATTERY  
PACK  
The phone comes with a rechargeable  
nickel-cadmium battery pack in the handset,  
but not connected. Before using your phone,  
you must connect the battery pack, then  
charge it for about 24 hours.  
5. Plug the adapter into a standard AC  
outlet.  
6. Push up on the handset holder, then lift  
and remove it. Turn it over and rotate it  
so that the oval-shaped indention is at  
the bottom, then slide it down into its  
slot. Snap it back into place so that it  
holds the handset.  
1. Press down and slide off the battery  
compartment cover.  
2. Lift the battery pack out of the  
compartment.  
On a Wall  
3. Plug the battery pack’s connector into  
the socket in the compartment (the  
connector fits only one way), then place  
the battery pack in the compartment.  
To mount the phone directly on a wall, you  
need two screws (not supplied) with heads  
that fit into the keyhole slots on the bottom of  
the base.  
4. Replace the cover.  
1. Drill two holes 315/16 inches (100 mm)  
apart. Then thread a screw into each  
hole, letting the heads extend about 1/8  
inch (3 mm) from the wall.  
To charge the battery pack, place the  
handset either faceup or facedown on the  
base. The CHARGE/IN USE indicator on the  
base lights and JejWb0&& appears on the  
handset display.  
2. Plug one end of the supplied long  
TEL LINE  
modular cord into the  
the back of the base.  
jack on  
Recharge the battery pack when Bem 8Wjj[ho  
flashes on the display.  
3. Insert the supplied AC adapter’s barrel  
DC IN 9V  
plug into the  
the base.  
jack on the back of  
Important:  
Be sure the battery pack is  
properly connected before you try to charge  
it. The CHARGE/IN USE indicator lights  
when the handset is on the base, even if the  
battery pack is not connected.  
4. Route the adapter and modular cords  
through the grooves on the bottom of  
the base.  
Notes:  
5. Align the base’s keyhole slots with the  
mounting screws and slide the base  
downward to secure it.  
• When you first use the phone after  
charging or recharging the battery pack,  
the phone might not work and you might  
hear an error tone when you press  
TALK  
. Return the handset to the base for  
8
Installation  
 
about 5 seconds to reset the security  
access-protection code.  
a replacement battery pack through your  
local RadioShack store. Install the new  
battery pack and charge it for about 24  
hours.  
• If the base loses power for about an  
hour while the handset is away from it,  
the security access-protection code  
might be lost. To reset the code, return  
the handset to the base for about 5  
seconds.  
Warning:  
Dispose of the old battery pack  
promptly and properly. Do not burn or bury it.  
See “Battery Safety Instructions” on Page 4  
for additional information on proper battery  
handling.  
The handset does lose its security  
access-protection code if the battery  
pack is completely discharged. Place  
the handset on the base to recharge the  
battery pack and reset the code.  
If you have trouble replacing the battery  
pack, take the phone to your local  
RadioShack for assistance.  
Important:  
The EPA certified  
• Using a pencil eraser, clean the  
charging contacts on the handset and  
base about once a month.  
RBRC® Battery Recycling Seal  
on the nickel-cadmium (Ni-Cd)  
battery indicates RadioShack  
is voluntarily participating in an  
• If the battery pack becomes weak during  
a call, the handset beeps every 3  
seconds and Bem 8Wjj[ho flashes. When  
this happens, you cannot make a call  
until you recharge the battery pack.  
industry program to collect and recycle these  
batteries at the end of their useful life, when  
taken out of service in the United States or  
Canada. The RBRC program provides a  
convenient alternative to placing used Ni-Cd  
batteries into the trash or the municipal  
waste stream, which may be illegal in your  
area. Please call 1-800-THE-SHACK (1-  
800-843-7422) for information on Ni-Cd  
battery recycling and disposal bans/  
restrictions in your area. RadioShack’s  
involvement in this program is part of the  
company’s commitment to preserving our  
environment and conserving our natural  
resources.  
• About once a month, fully discharge the  
battery by keeping the handset off the  
base until Bem 8Wjj[ho flashes on the  
display. Otherwise, the battery pack  
loses its ability to fully recharge.  
• If the display is blank and the phone  
does not work, recharge the battery  
pack. (The battery power might be too  
low to light the display.)  
• If you are not going to use your phone  
for an extended period, disconnect the  
battery pack. This increases the battery  
pack’s usable life.  
SETTING THE DIALING  
MODE  
Your phone is set for tone dialing. If you have  
pulse service, change the dialing mode. If  
you are not sure which type of service you  
have, do this test.  
• The supplied battery pack should last for  
about a year. If the battery pack does  
not hold a charge for more than 2 hours  
after an overnight charge, replace it with  
a new 3.6-volt, 600 mAh battery pack  
with a connector that fits the socket in  
the battery compartment. You can order  
TALK  
1. Lift the handset, press  
for a dial tone.  
, and listen  
0
2. Press any number other than .  
9
Installation  
 
Note:  
CALL ID  
1. Lift the handset and hold down  
If your phone system requires that  
you dial an access code (9, for example)  
before you dial an outside number, do  
not dial the access code either.  
until the menu appears with 7kje JWba  
selected.  
SELECT  
2. Press  
to change the Auto Talk  
If the dial tone stops, you have touch-  
tone service. If the dial tone continues,  
you have pulse service.  
setting. Ed or E\\ appears indicating the  
selected setting.  
3. Return the handset to the base (or press  
TALK  
CALL ID  
) to store the new setting.  
3. Press  
.
FLASH  
To set the dialing mode, hold down  
TURNING CALLER ID/CALL  
WAITING ON/OFF  
until the phone beeps and the current dialing  
mode appears. Press /7 to set pulse mode  
#
/TONE/  
or ∗  
6 to set tone mode. Fkbi[ :_Wb_d]  
If you subscribe to Call Waiting with Caller ID  
service, you can set the phone to show  
Caller ID information for an incoming call  
even while you are using the phone.  
or Jed[ :_Wb_d] appears.  
Note:  
The phone exits the setting mode if a  
TALK  
call or page is received, or if you press  
.
Follow these steps to turn the Caller ID/Call  
Waiting feature on or off.  
SETTING THE RINGER TONE  
AND VOLUME  
CALL ID  
1. Lift the handset and hold down  
You can select one of four different ringer  
tone/volume settings on the handset. Lift the  
handset and repeatedly press 8 or 9 to  
select the desired ringer setting. Each time  
you press the button, the phone rings at the  
selected setting and the display shows H_d]ý  
Jof[ý7ý>_]^, H_d]ýJof[ý7ýBem, H_d]ýJof[ý8ý>_]^,  
or H_d]ýJof[ý8ýBem.  
until the menu appears with 7kje JWba  
selected.  
2
2. Press or 9 to move the cursor to  
9?:9M0 (Caller ID/Call Waiting).  
SELECT  
3. Press  
to turn the Caller ID/Call  
Waiting setting on or off. Ed or E\\  
appears indicating the selected setting.  
TURNING AUTO TALK ON/  
OFF  
4. Return the handset to the base to store  
the new setting.  
Your phone is preset so you must press  
STORING YOUR AREA  
CODE  
TALK  
when you lift the handset from the base  
to answer a call. With Auto Talk turned on,  
you can answer a call by just lifting the  
handset from the base. If the handset is  
away from the base, you can answer by  
pressing any key.  
You can store your local area code in the  
phone’s memory so it will not show the area  
code if you receive a local call. If you need to  
add or store the area code for a local  
number, you can add it afterwards (see  
“Adding/Deleting the Area Code” on  
Page 16).  
Follow these steps to turn Auto Talk on or  
off.  
Important:  
In some areas, the area code is  
necessary even for a local call. If you live in  
10  
Installation  
 
SELECT  
to store the area code,  
such an area, do not store the area code.  
Follow these steps to store your area code.  
4. Press  
CALL ID  
then press  
or return the handset  
to the base to clear the display.  
CALL ID  
1. Lift the handset and hold down  
until the menu appears with 7kje JWba  
selected.  
SELECTING THE  
LANGUAGE  
3
2. Press or 9 to move the cursor to 7h[Wý  
You can select the language on the display,  
either English or French.  
9eZ[0.  
SELECT  
3. Press  
, then enter your three-  
Follow these steps to select the language.  
digit area code. If you make a mistake,  
/TONE/  
#
repeatedly press ∗  
6 or /7 to  
CALL ID  
1. Lift the handset and hold down  
move the cursor over the incorrect digit,  
then enter the correct number.  
until the menu appears with 7kje JWba  
selected.  
Note:  
If an area code is already stored,  
4
2. Press or 9 to move the cursor to  
it appears on the display after you hold  
down  
BWd]kW][.  
CALL ID  
DELETE  
three  
. Press  
times to delete the area code. Then  
enter your area code.  
SELECT  
3. Press  
to select ;d] (English) or  
<h$ (French).  
4. Return the handset to the base or press  
CALL ID  
to store the new setting.  
ˆ Operation  
The handset window has plastic film on it to  
protect it during shipment. Carefully peel off  
the film before using your phone.  
then enter the correct number. To delete the  
DELETE  
entire number, hold down  
.
When you receive a call, ?dYec_d] 9Wbb  
appears. To answer the call, lift the handset  
MAKING AND RECEIVING  
CALLS  
TALK  
and press  
. If Auto Talk is on, just lift the  
handset. If the handset is away from the  
base, press any key. JWba appears on the  
handset’s display. To end a call, place the  
To make a call, lift the handset and press  
TALK  
. JWba and the current volume setting  
TALK  
handset on the base or press  
.
appear on the handset’s display, and the  
CHARGE/IN USE indicator on the base  
lights. Dial the number. The number appears  
on the handset as you dial, then the call’s  
elapsed time appears. To end a call, place  
SELECTING THE CHANNEL  
The phone has 40 channels. If the call  
disconnects or you experience difficulty  
hearing the conversation during a call, press  
TALK  
the handset on the base or press  
.
CH  
on the handset to select a different  
You can also dial the number before you  
channel. IYWdd_d] appears as your phone  
searches for a clear channel.  
TALK  
press  
. If you make a mistake, press  
DELETE  
until the incorrect entry is erased,  
11  
Operation  
 
Note:  
services, pressing  
the current call.  
If you do not have any special phone  
ADJUSTING THE  
HANDSET’S VOLUME  
FLASH  
might disconnect  
To adjust the volume of the sound you hear  
through the handset during a call, press 8  
or 9 on the handset until you obtain the  
desired volume level. Lebkc[ CWn_ckc,  
Lebkc[ >_]^, Lebkc[ C[Z_kc, or Lebkc[ Bem  
appears on the handset display. Once you  
set the volume level, the setting is  
maintained even after you hang up the  
phone.  
USING TONE SERVICES ON  
A PULSE LINE  
Some special services require tone signals  
(such as bank-by-phone). If you have pulse  
dialing, you can still use these special tone  
services.  
Dial the service’s main number. When the  
Note:  
When you press 8 while the volume  
/TONE/  
service answers, press ∗  
6. Any  
is maximum or 9 while the volume is low,  
the setting does not change. The phone  
sounds three short beeps.  
additional numbers you dial are sent as tone  
signals.  
The phone’s dial mode resets to pulse when  
you make or receive a call.  
USING REDIAL  
You can quickly dial the last number you  
PAGING  
REDIAL/  
dialed. Lift the handset and press  
PAUSE  
TALK  
. The phone dials the  
, then  
To send a page from the base to the handset  
or to locate the handset when the phone is  
number.  
PAGE/FIND  
not in use, press  
on the base.  
Notes:  
The handset beeps for about 1 minute.  
REDIAL/PAUSE  
You can also press  
after  
FW]_d] appears on the handset while the  
page sounds.  
TALK  
pressing  
.
• The redial memory holds up to 32 digits,  
so you can redial long-distance as well  
as local numbers.  
To stop the page, press any key on the  
handset, place the handset on the base, or  
PAGE/FIND  
press  
on the base again.  
• The redial memory also holds pause  
entries (see “Entering a Pause” on  
Page 14).  
Note:  
The phone rings when a call comes in  
while you are using the page feature.  
USING A HEADSET  
USING FLASH  
You can make or answer calls with hands-  
free convenience using an optional headset  
that has a 3/32-inch (2.5-mm) plug. Your local  
RadioShack store has a variety of headsets  
available.  
FLASH  
performs the electronic equivalent of  
a switchhook operation for special services,  
such as Call Waiting. For example, if you  
have Call Waiting, press  
FLASH  
to answer an  
incoming call without disconnecting the  
FLASH  
current call. Press  
the first call.  
again to return to  
To connect the headset, gently flip open the  
rubber headset jack cover on the side of the  
handset, then insert the headset’s plug into  
the jack.  
12  
Operation  
 
Notes:  
• Connecting a headset disconnects the  
SELECT  
. Ijeh[ DWc[ appears. If  
you do not want to enter a name, skip to  
Step 6.  
4. Press  
handset’s earpiece and microphone.  
5. To enter a name, use the number keys.  
8 or 9 on the handset also controls  
the headset’s volume.  
Refer to the letters on the number keys  
to select the desired letter. Press the key  
once for the first letter in the upper case,  
press twice for second letter in the upper  
case, and so on. To enter the lower case  
letter, press four times (or five times) to  
display the first letter in lower case, five  
or six times for second letter, and so on.  
• If you place the handset on the base to  
recharge it while the headset is  
connected, be sure the handset seats  
properly.  
• With a headset connected, you can  
make or answer calls as usual using the  
keys on the handset.  
5
For example, to enter John: press  
once; upper case @ appears. Then press  
You can use a handset holder (available  
from your local RadioShack store) to  
hang the handset on your belt for  
greater convenience when using a  
headset.  
6
4
six times; lower case e appears. Press  
five times; lower case ^ appears.  
6
Finally, press five times; lower case d  
appears.  
To enter two letters from the same key in  
• When you finish using the headset,  
disconnect it from the handset and close  
the rubber cover to protect the jack.  
#
a row, press /7 to move the cursor to  
the next position. For example to enter  
#
AB, press 2; 7 appears. Then press /  
7, the cursor moves to next position,  
then press 2 twice so 8 appears.  
MEMORY DIALING  
You can store up to 10 phone numbers and  
names in memory, then dial a stored number  
by entering its memory location number.  
Each number can be up to 20 digits, and  
each name can be up to 14 characters.  
#
To enter a space, press /7 twice  
without entering any character.  
To enter a number, repeatedly press the  
corresponding number key until the  
number appears.  
Storing a Number and Name in  
Memory  
0
To enter a special character, press .  
0
Each time you press , the following  
characters appear in this order:  
1. Lift the handset.  
#
&
¶ âýá (space) &  
MEM  
2. Hold down  
until C[ceho Ijeh[ and a  
list of memory location numbers  
appears.  
/TONE/  
If you make a mistake, use ∗  
6
#
or /7 to move the cursor over the  
error, then enter the correct character, or  
3. Select an empty memory location (or the  
one you want to replace) by entering the  
DELETE  
press  
to delete a character. To  
DELETE  
delete all characters, hold down  
for at least 1 second.  
1 0  
location number ( – ) or using 8 or 9  
to scroll through the list.  
SELECT  
6. Press  
. Ijeh[ DkcX[h appears.  
13  
Operation  
 
7. Enter the number and any tone and  
pause entries (see “Using Tone Services  
on a Pulse Line” on Page 12 and  
“Entering a Pause”).  
;
                                                       
Z
                                                        
_
                                                        
j
                                                         
C
                                                          
[
                                                           
c
                                                            
e
                                                             
h
                                                              
o
                                                              
d
                                                               
— edit the record as  
described in Steps 5 through 8 of  
“Storing a Number and Name in  
Memory” on Page 13.  
Note:  
one digit of memory.  
Each tone or pause entry uses  
:[b[j[ C[ceho d — the display prompts  
you to confirm the deletion. Press 8 or  
9 to move the cursor to O[i, then press  
SELECT  
8. Press  
. The phone beeps and  
SELECT  
DELETE  
. The phone beeps,  
or  
C[ceho d Ijeh[Z appears (d = number).  
After a few seconds, C[ceho Ijeh[  
appears, and you can repeat Steps 3–8  
to store more numbers.  
and C[ceho d :[b[j[Z appears.  
=e 8WYa — returns you to the list of  
memory numbers.  
To replace a stored number, simply store a  
new one in its place.  
Reviewing Memory Numbers  
To review your memory numbers, press  
MEM  
Entering a Pause  
. The list of memory location numbers  
('&) appears with the name stored with each  
number (or 2C[ceho d4 if you did not store a  
name).  
In some telephone systems, you must dial an  
access code (9, for example) and wait for a  
second dial tone before you can dial an  
outside number. You can store the access  
code with the phone number. However, you  
should also store a pause after the access  
code to allow the outside line time to  
connect.  
#
To see the stored phone numbers, press /  
7. Only the first 13 characters/numbers  
appear for number. To see the rest of the  
#
number, press /7 when the number is on  
/TONE/  
the display. Press ∗  
6 to return to the  
name display.  
REDIAL/  
To enter a 2-second pause, press  
PAUSE  
MEM  
.
. You can add more pause entries for  
To exit the memory number list, press  
a longer pause.  
Note:  
To view the name and number at the  
SELECT  
same time, press  
when the cursor is  
Editing or Deleting a Number in  
Memory  
by a memory location number. To exit this  
DELETE  
display, hold down  
clears.  
until the display  
1. Lift the handset.  
MEM  
2. Hold down  
until C[ceho Ijeh[ and a  
Dialing a Memory Number  
list of memory location numbers appear  
on the handset display.  
To dial a number stored in memory, lift the  
MEM  
handset and press  
. The list of memory  
3. Choose a memory location ('&) by  
pressing a number or by repeatedly  
pressing 8 or 9.  
location numbers appears. Choose a  
memory location ('&) by pressing a number  
or by repeatedly pressing 8 or 9, then  
TALK  
press  
.
SELECT  
4. Press  
. Three options (;Z_j  
C[ceho d, :[b[j[ C[ceho d and =e 8WYa)  
You can also dial a memory number after  
TALK  
MEM  
(the display does  
appear. Press 8 or 9 to choose the  
pressing  
. Press  
SELECT  
option then press  
to choose it.  
not change but the phone’s memory recall  
14  
Operation  
 
activates), then press the desired memory  
location number.  
and enter the number for the location where  
the additional information is stored.  
Chain-Dialing Service Numbers  
Testing Stored Emergency Num-  
bers  
For quick recall of numbers for special  
services (such as bank-by-phone), store  
each group of numbers in its own memory  
location.  
If you store an emergency service’s number  
(police department, fire department,  
ambulance) and you choose to test the  
stored number, make the test call during the  
late evening or early morning hours to avoid  
peak demand periods. Also, remain on the  
line to explain the reason for your call.  
Dial the service’s main number first. Then, at  
MEM  
the appropriate place in the call, press  
ˆ Caller ID Operation  
If you subscribe to Caller ID service from  
your phone company, the phone company  
sends information about the call, as well as  
the time and date, between the first and  
second rings of every call you receive. The  
phone displays this information after the  
second ring, and it stores up to 30 Caller ID  
records for later review. It also shows if the  
caller information is unavailable or if the  
name and number were blocked by the caller  
(see “Caller ID Messages”).  
Where Caller ID is offered, one or more  
options are generally available:  
• caller’s number only  
• caller’s name only  
• caller’s name and number  
REVIEWING CALLER ID  
RECORDS  
If the handset is face-up on the base, it  
shows the number of new and total Caller ID  
records and lets you view the display for any  
new records.  
If you subscribe to Call Waiting with Caller  
ID, you hear a tone through the handset  
when a call comes in, then the Caller ID  
record appears.  
To review the Caller ID records, lift the  
If the phone’s Caller ID memory becomes  
full, any new call replaces the oldest call’s  
record.  
CALL ID  
handset and press  
. The number of  
new Caller ID records, if any, and the total  
number of records appears. Repeatedly  
press 9 to scroll through the Caller ID  
records from the newest to the oldest, or 8  
to scroll back through the records. To scroll  
quickly through the records, hold down 8 or  
9.  
IMPORTANT CALLER ID  
INFORMATION  
To use the phone’s Caller ID and Caller ID  
with Call Waiting features, you must be in an  
area where those services are available and  
you must subscribe to those services  
through your local phone company.  
The top line of each record shows the date,  
time and the number of calls from that  
number. The second line shows the caller’s  
15  
Caller ID Operation  
 
name (if available), and the third line shows  
the caller’s phone number.  
ADDING/DELETING THE  
AREA CODE  
The display shows the area code of an  
incoming call, unless the call comes from the  
area code you stored (see “Storing Your  
Area Code” on Page 10). You can add the  
area code to the display or delete it. With the  
Caller ID Messages  
Display  
English  
French  
Description  
3
record displayed, press to add or delete the  
area code.  
Shows the number of  
new Caller ID records  
(records you have not  
reviewed) and the  
total number of  
D[m0ýNN  
JejWb0ýNN  
Dekl$0ýNN  
JejWb0ýNN  
Numbers are stored in memory as they  
appear on the display, with or without the  
area code. Numbers in Caller ID records  
remain the same, even if you add or delete  
the area code.  
records.  
Fh_lWj[ DWc[ýor  
Fh_lWj[ DkcX[h  
Dec Yed\_Z[dj_[býor  
De Yed\_Z[dj_[b  
The caller has  
blocked the caller ID  
information.  
DIALING NUMBERS FROM A  
CALLER ID RECORD  
Kdademd DWc[ or  
Kdademd DkcX[h  
Decý_dYeddk  
The caller is not within  
a Caller ID service  
area.  
To dial a local number stored in a Caller ID  
record, recall the record, then press  
TALK  
.
orýDeý_dYeddk  
3
To add or delete the area code, press  
?dYecfb[j[ :WjW  
:edd[[i _dYec$  
Appears if there was  
an error during the  
transmission of Caller  
ID information. Occa-  
sional errors are nor-  
mal. If the phone  
TALK  
before you press  
.
1
If the call is long distance, press (' appears  
before the displayed number) before you  
TALK  
press  
.
frequently displays  
Incomplete Data, con-  
tact your local tele-  
phone company or  
your local RadioShack  
store.  
Note:  
If a Caller ID record does not contain a  
phone number (if it was blocked by the caller,  
for example) you cannot dial from that  
record.  
STORING A CALLER ID  
RECORD IN MEMORY  
Follow these steps to store the name and  
number from a Caller ID record into a  
memory location.  
CALL ID  
1. Press  
then 9 to recall the  
record you want to store. To add or  
3
delete the area code, press . If it is a  
1
long distance number, press .  
MEM  
2. Press  
. I[b[Yj BeYWj_ed appears.  
16  
Caller ID Operation  
 
1 0  
3. Choose a memory location ( – ) by  
3. Press 8 to move the cursor to O[i, then  
SELECT  
DELETE  
. The phone  
pressing a number or by repeatedly  
press  
or  
SELECT  
pressing 8 or 9, then press  
.
beeps once and JEJ7B0&& appears,  
indicating that all Caller ID records were  
deleted.  
If the selected location is empty, the  
phone beeps to confirm that it stored the  
number, then the Caller ID record  
appears.  
If a record exists in the selected  
location, H[fbWY[ C[ceho5 appears,  
prompting you to confirm the  
replacement. Press 8 or 9 to move  
the cursor to O[i or De, then press  
SELECT  
.
DELETING CALLER ID  
RECORDS  
You can delete Caller ID records individually  
or all at once.  
Deleting a Single Caller ID Record  
Follow these steps to delete a single Caller  
ID record.  
CALL ID  
1. Press  
then 9 to recall the  
record you want to delete.  
DELETE  
2. Press  
. :[b[j[ C[iiW][5 appears,  
prompting you to confirm the deletion.  
3. Press 8 to move the cursor to O[i, then  
SELECT  
DELETE  
. The phone  
press  
or  
beeps once, indicating that the record  
was deleted.  
Deleting All Caller ID Records  
Follow these steps to delete all Caller ID  
records.  
CALL ID  
1. Press  
so the record totals  
appear.  
DELETE  
2. Press  
. :[b[j[ 7bb5 appears,  
prompting you to confirm the deletion.  
17  
Caller ID Operation  
 
ˆ Troubleshooting  
We do not expect you to have any problems with your phone, but if you do, these suggestions  
might help.  
Problem  
Suggestions  
The phone does not  
work or works poorly.  
Be sure the base’s phone line cord and AC adapter are correctly and securely  
connected.  
Be sure the battery pack in the handset is connected and charged.  
Return the handset to the base for about 5 seconds to reset the security  
access-protection code.  
The display flashes  
slowly when the hand-  
set is faceup on the  
base.  
Make sure the battery pack in the handset is properly connected.  
The handset stops  
working or works  
poorly during a call.  
Move the handset closer to the base.  
Lift the base’s antenna to a fully vertical position.  
Be sure the handset’s battery pack is charged. (If the battery pack power is too  
low, the handset cannot display Bem 8Wjj[ho.)  
Low volume or  
unusual sounds.  
Someone has picked up another phone on the same line. Hang up the other  
phone.  
Your conversation is  
difficult to hear due to  
dropout or muting.  
Keep the handset away from computers, remote control toys, wireless micro-  
phones, alarm systems, intercoms, room monitors, fluorescent lights, and elec-  
trical appliances.  
Move to another location or turn off the source of interference.  
CH  
Press  
to change the channel.  
Hang up and redial the number.  
The phone cannot be  
operated at a useful  
distance from the base  
because the signal  
becomes weak or  
Lift the base’s antenna to a vertical position.  
Be sure neither the handset’s nor base’s antenna is touching a metal surface.  
Return the handset to the base and recharge the battery pack.  
noisy (handset’s range  
has decreased).  
The handset battery  
Check the charging contacts on the handset and base. If they are dirty, clean  
pack does not charge. them with a pencil eraser.  
Be sure the battery pack is connected correctly.  
Be sure the handset is properly seated on the base.  
Replace the battery pack.  
18  
Troubleshooting  
 
Problem  
Suggestions  
The handset does not Move the handset closer to the base.  
ring or receive a page.  
Lift base’s antenna to a vertical position.  
Be sure the battery pack in the handset is connected and charged.  
Move the base away from other electrical devices.  
You have an incoming Let the phone ring twice before you answer so the system has time to record  
call, but do not receive the Caller ID information.  
any Caller ID informa-  
tion.  
Check that the system is correctly and securely connected.  
Check with your phone company to verify that your Caller ID service is active.  
If you still have problems, disconnect the phone. If other phones on the same line work  
properly, the fault is in this phone or its installation. If you cannot find the problem, take the  
phone to your local RadioShack store for assistance.  
CARE  
Keep the phone dry; if it gets wet, wipe it dry  
immediately. Use and store the phone only in  
normal temperature environments. Handle  
the phone carefully; do not drop it. Keep the  
phone away from dust and dirt, and wipe it  
with a damp cloth occasionally to keep it  
looking new.  
Modifying or tampering with the telephone’s  
internal components can cause a  
malfunction and might invalidate its warranty  
and void your FCC authorization to operate  
it. If your telephone is not performing as it  
should, take it to your local RadioShack store  
for assistance. If the trouble is affecting the  
telephone lines, the phone company can ask  
you to disconnect your telephone until you  
have resolved the problem.  
19  
Troubleshooting  
 
Limited One-Year Warranty  
This product is warranted by RadioShack against manufacturing defects in material and workman-  
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned  
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING  
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED  
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED  
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-  
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY  
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-  
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-  
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS  
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-  
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-  
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to  
you.  
In the event of a product defect during the warranty period, take the product and the RadioShack  
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-  
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and  
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase  
price. All replaced parts and products, and products on which a refund is made, become the prop-  
erty of RadioShack. New or reconditioned parts and products may be used in the performance of  
warranty service. Repaired or replaced parts and products are warranted for the remainder of the  
original warranty period. You will be charged for repair or replacement of the product made after the  
expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,  
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or  
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs  
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as  
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs  
of product removal, installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102  
12/99  
D
43-1122  
UCZZ01346BZ  
10A01  
Printed in China  
RadioShack Corporation  
Fort Worth, Texas 76102  
 

Ricoh Photo Scanner IS450 User Guide
Rockford Fosgate Speaker RFB3081 User Guide
Rockford Fosgate Stereo Amplifier PUNCH100 User Guide
Rosen Entertainment Systems DVR RVR 2000 User Guide
Royal Leisure Camping Equipment WINDSOR 390 User Guide
Samsung Air Conditioner MH026FNCA User Guide
Samsung Bluetooth Headset WEP301 User Guide
Samsung Refrigerator GI6FARXXQ User Guide
Sanitaire Sander SC6010A User Guide
SECO LARM USA Door SD 997B User Guide